mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
0f9595b9fa
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries to defconfigs. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> [trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
110 lines
2.7 KiB
Text
110 lines
2.7 KiB
Text
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_SPL_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_TARGET_LS1021AQDS=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x1002000
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_SYS_MEMTEST_START=0x80000000
|
|
CONFIG_SYS_MEMTEST_END=0x9fffffff
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x140000
|
|
CONFIG_SYS_I2C_MXC_I2C1=y
|
|
CONFIG_SYS_I2C_MXC_I2C2=y
|
|
CONFIG_SYS_I2C_MXC_I2C3=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-qds-duart"
|
|
CONFIG_SPL_TEXT_BASE=0x10000000
|
|
CONFIG_FSL_USE_PCA9547_MUX=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_AHCI=y
|
|
CONFIG_SYS_LOAD_ADDR=0x82000000
|
|
CONFIG_FIT=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="NAND_BOOT"
|
|
CONFIG_DYNAMIC_SYS_CLK_FREQ=y
|
|
CONFIG_RAMBOOT_PBL=y
|
|
CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1021aqds/ls102xa_pbi.cfg"
|
|
CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1021aqds/ls102xa_rcw_nand.cfg"
|
|
CONFIG_NAND_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_SILENT_CONSOLE=y
|
|
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_ID_EEPROM=y
|
|
CONFIG_SPL_FSL_PBL=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xe8
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_MPC8XXX_INIT_DDR=y
|
|
CONFIG_SPL_NAND_SUPPORT=y
|
|
CONFIG_SPL_WATCHDOG=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_BOOTZ=y
|
|
CONFIG_CMD_IMLS=y
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_MEMINFO=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_EXT2=y
|
|
CONFIG_CMD_FAT=y
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_NAND=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
|
|
CONFIG_SYS_FSL_DDR3=y
|
|
CONFIG_DDR_ECC=y
|
|
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
|
|
CONFIG_MPC8XXX_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SPL_SYS_I2C_LEGACY=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x57
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_NOR_FLASH=y
|
|
CONFIG_FLASH_CFI_DRIVER=y
|
|
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
|
CONFIG_SYS_FLASH_CFI=y
|
|
CONFIG_SYS_MAX_FLASH_BANKS=2
|
|
CONFIG_NAND_FSL_IFC=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
|
|
CONFIG_SYS_NAND_U_BOOT_OFFS=0x1c000
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_TSEC_ENET=y
|
|
CONFIG_NVME=y
|
|
CONFIG_PCI=y
|
|
CONFIG_DM_PCI_COMPAT=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_USB_STORAGE=y
|