mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 02:08:38 +00:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
286 lines
7.2 KiB
ArmAsm
286 lines
7.2 KiB
ArmAsm
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
*
|
|
* (C) Copyright 2009
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include "asm/arch/orion5x.h"
|
|
|
|
/*
|
|
* Configuration values for SDRAM access setup
|
|
*/
|
|
|
|
#define SDRAM_CONFIG 0x3148400
|
|
#define SDRAM_MODE 0x62
|
|
#define SDRAM_CONTROL 0x4041000
|
|
#define SDRAM_TIME_CTRL_LOW 0x11602220
|
|
#define SDRAM_TIME_CTRL_HI 0x40c
|
|
#define SDRAM_OPEN_PAGE_EN 0x0
|
|
/* DDR 1 2x 32M NANYA NT5DS16M16CS-6K ==> 64MB */
|
|
#define SDRAM_BANK0_SIZE 0x3ff0001
|
|
#define SDRAM_ADDR_CTRL 0x10
|
|
|
|
#define SDRAM_OP_NOP 0x05
|
|
#define SDRAM_OP_SETMODE 0x03
|
|
|
|
#define SDRAM_PAD_CTRL_WR_EN 0x80000000
|
|
#define SDRAM_PAD_CTRL_TUNE_EN 0x00010000
|
|
#define SDRAM_PAD_CTRL_DRVN_MASK 0x0000003f
|
|
#define SDRAM_PAD_CTRL_DRVP_MASK 0x00000fc0
|
|
|
|
/*
|
|
* For Guideline MEM-3 - Drive Strength value
|
|
*/
|
|
|
|
#define DDR1_PAD_STRENGTH_DEFAULT 0x00001000
|
|
#define SDRAM_PAD_CTRL_DRV_STR_MASK 0x00003000
|
|
|
|
/*
|
|
* For Guideline MEM-4 - DQS Reference Delay Tuning
|
|
*/
|
|
|
|
#define MSAR_ARMDDRCLCK_MASK 0x000000f0
|
|
#define MSAR_ARMDDRCLCK_H_MASK 0x00000100
|
|
|
|
#define MSAR_ARMDDRCLCK_333_167 0x00000000
|
|
#define MSAR_ARMDDRCLCK_500_167 0x00000030
|
|
#define MSAR_ARMDDRCLCK_667_167 0x00000060
|
|
#define MSAR_ARMDDRCLCK_400_200_1 0x000001E0
|
|
#define MSAR_ARMDDRCLCK_400_200 0x00000010
|
|
#define MSAR_ARMDDRCLCK_600_200 0x00000050
|
|
#define MSAR_ARMDDRCLCK_800_200 0x00000070
|
|
|
|
#define FTDLL_DDR1_166MHZ 0x0047F001
|
|
|
|
#define FTDLL_DDR1_200MHZ 0x0044D001
|
|
|
|
/*
|
|
* Low-level init happens right after start.S has switched to SVC32,
|
|
* flushed and disabled caches and disabled MMU. We're still running
|
|
* from the boot chip select, so the first thing SPL should do is to
|
|
* set up the RAM to copy U-Boot into.
|
|
*/
|
|
|
|
.globl lowlevel_init
|
|
|
|
lowlevel_init:
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
|
|
/* Use 'r4 as the base for internal register accesses */
|
|
ldr r4, =ORION5X_REGS_PHY_BASE
|
|
|
|
/* move internal registers from the default 0xD0000000
|
|
* to their intended location, defined by SoC */
|
|
ldr r3, =0xD0000000
|
|
add r3, r3, #0x20000
|
|
str r4, [r3, #0x80]
|
|
|
|
/* Use R3 as the base for DRAM registers */
|
|
add r3, r4, #0x01000
|
|
|
|
/*DDR SDRAM Initialization Control */
|
|
ldr r6, =0x00000001
|
|
str r6, [r3, #0x480]
|
|
|
|
/* Use R3 as the base for PCI registers */
|
|
add r3, r4, #0x31000
|
|
|
|
/* Disable arbiter */
|
|
ldr r6, =0x00000030
|
|
str r6, [r3, #0xd00]
|
|
|
|
/* Use R3 as the base for DRAM registers */
|
|
add r3, r4, #0x01000
|
|
|
|
/* set all dram windows to 0 */
|
|
mov r6, #0
|
|
str r6, [r3, #0x504]
|
|
str r6, [r3, #0x50C]
|
|
str r6, [r3, #0x514]
|
|
str r6, [r3, #0x51C]
|
|
|
|
/* 1) Configure SDRAM */
|
|
ldr r6, =SDRAM_CONFIG
|
|
str r6, [r3, #0x400]
|
|
|
|
/* 2) Set SDRAM Control reg */
|
|
ldr r6, =SDRAM_CONTROL
|
|
str r6, [r3, #0x404]
|
|
|
|
/* 3) Write SDRAM address control register */
|
|
ldr r6, =SDRAM_ADDR_CTRL
|
|
str r6, [r3, #0x410]
|
|
|
|
/* 4) Write SDRAM bank 0 size register */
|
|
ldr r6, =SDRAM_BANK0_SIZE
|
|
str r6, [r3, #0x504]
|
|
/* keep other banks disabled */
|
|
|
|
/* 5) Write SDRAM open pages control register */
|
|
ldr r6, =SDRAM_OPEN_PAGE_EN
|
|
str r6, [r3, #0x414]
|
|
|
|
/* 6) Write SDRAM timing Low register */
|
|
ldr r6, =SDRAM_TIME_CTRL_LOW
|
|
str r6, [r3, #0x408]
|
|
|
|
/* 7) Write SDRAM timing High register */
|
|
ldr r6, =SDRAM_TIME_CTRL_HI
|
|
str r6, [r3, #0x40C]
|
|
|
|
/* 8) Write SDRAM mode register */
|
|
/* The CPU must not attempt to change the SDRAM Mode register setting */
|
|
/* prior to DRAM controller completion of the DRAM initialization */
|
|
/* sequence. To guarantee this restriction, it is recommended that */
|
|
/* the CPU sets the SDRAM Operation register to NOP command, performs */
|
|
/* read polling until the register is back in Normal operation value, */
|
|
/* and then sets SDRAM Mode register to its new value. */
|
|
|
|
/* 8.1 write 'nop' to SDRAM operation */
|
|
ldr r6, =SDRAM_OP_NOP
|
|
str r6, [r3, #0x418]
|
|
|
|
/* 8.2 poll SDRAM operation until back in 'normal' mode. */
|
|
1:
|
|
ldr r6, [r3, #0x418]
|
|
cmp r6, #0
|
|
bne 1b
|
|
|
|
/* 8.3 Now its safe to write new value to SDRAM Mode register */
|
|
ldr r6, =SDRAM_MODE
|
|
str r6, [r3, #0x41C]
|
|
|
|
/* 8.4 Set new mode */
|
|
ldr r6, =SDRAM_OP_SETMODE
|
|
str r6, [r3, #0x418]
|
|
|
|
/* 8.5 poll SDRAM operation until back in 'normal' mode. */
|
|
2:
|
|
ldr r6, [r3, #0x418]
|
|
cmp r6, #0
|
|
bne 2b
|
|
|
|
/* DDR SDRAM Address/Control Pads Calibration */
|
|
ldr r6, [r3, #0x4C0]
|
|
|
|
/* Set Bit [31] to make the register writable */
|
|
orr r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
str r6, [r3, #0x4C0]
|
|
|
|
bic r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
bic r6, r6, #SDRAM_PAD_CTRL_TUNE_EN
|
|
bic r6, r6, #SDRAM_PAD_CTRL_DRVN_MASK
|
|
bic r6, r6, #SDRAM_PAD_CTRL_DRVP_MASK
|
|
|
|
/* Get the final N locked value of driving strength [22:17] */
|
|
mov r1, r6
|
|
mov r1, r1, LSL #9
|
|
mov r1, r1, LSR #26 /* r1[5:0]<DrvN> = r3[22:17]<LockN> */
|
|
orr r1, r1, r1, LSL #6 /* r1[11:6]<DrvP> = r1[5:0]<DrvN> */
|
|
|
|
/* Write to both <DrvN> bits [5:0] and <DrvP> bits [11:6] */
|
|
orr r6, r6, r1
|
|
str r6, [r3, #0x4C0]
|
|
|
|
/* DDR SDRAM Data Pads Calibration */
|
|
ldr r6, [r3, #0x4C4]
|
|
|
|
/* Set Bit [31] to make the register writable */
|
|
orr r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
str r6, [r3, #0x4C4]
|
|
|
|
bic r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
bic r6, r6, #SDRAM_PAD_CTRL_TUNE_EN
|
|
bic r6, r6, #SDRAM_PAD_CTRL_DRVN_MASK
|
|
bic r6, r6, #SDRAM_PAD_CTRL_DRVP_MASK
|
|
|
|
/* Get the final N locked value of driving strength [22:17] */
|
|
mov r1, r6
|
|
mov r1, r1, LSL #9
|
|
mov r1, r1, LSR #26
|
|
orr r1, r1, r1, LSL #6 /* r1[5:0] = r3[22:17]<LockN> */
|
|
|
|
/* Write to both <DrvN> bits [5:0] and <DrvP> bits [11:6] */
|
|
orr r6, r6, r1
|
|
|
|
str r6, [r3, #0x4C4]
|
|
|
|
/* Implement Guideline (GL# MEM-3) Drive Strength Value */
|
|
/* Relevant for: 88F5181-A1/B0/B1 and 88F5281-A0/B0 */
|
|
|
|
ldr r1, =DDR1_PAD_STRENGTH_DEFAULT
|
|
|
|
/* Enable writes to DDR SDRAM Addr/Ctrl Pads Calibration register */
|
|
ldr r6, [r3, #0x4C0]
|
|
orr r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
str r6, [r3, #0x4C0]
|
|
|
|
/* Correct strength and disable writes again */
|
|
bic r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
bic r6, r6, #SDRAM_PAD_CTRL_DRV_STR_MASK
|
|
orr r6, r6, r1
|
|
str r6, [r3, #0x4C0]
|
|
|
|
/* Enable writes to DDR SDRAM Data Pads Calibration register */
|
|
ldr r6, [r3, #0x4C4]
|
|
orr r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
str r6, [r3, #0x4C4]
|
|
|
|
/* Correct strength and disable writes again */
|
|
bic r6, r6, #SDRAM_PAD_CTRL_DRV_STR_MASK
|
|
bic r6, r6, #SDRAM_PAD_CTRL_WR_EN
|
|
orr r6, r6, r1
|
|
str r6, [r3, #0x4C4]
|
|
|
|
/* Implement Guideline (GL# MEM-4) DQS Reference Delay Tuning */
|
|
/* Relevant for: 88F5181-A1/B0/B1 and 88F5281-A0/B0 */
|
|
|
|
/* Get the "sample on reset" register for the DDR frequancy */
|
|
ldr r3, =0x10000
|
|
ldr r6, [r3, #0x010]
|
|
ldr r1, =MSAR_ARMDDRCLCK_MASK
|
|
and r1, r6, r1
|
|
|
|
ldr r6, =FTDLL_DDR1_166MHZ
|
|
cmp r1, #MSAR_ARMDDRCLCK_333_167
|
|
beq 3f
|
|
cmp r1, #MSAR_ARMDDRCLCK_500_167
|
|
beq 3f
|
|
cmp r1, #MSAR_ARMDDRCLCK_667_167
|
|
beq 3f
|
|
|
|
ldr r6, =FTDLL_DDR1_200MHZ
|
|
cmp r1, #MSAR_ARMDDRCLCK_400_200_1
|
|
beq 3f
|
|
cmp r1, #MSAR_ARMDDRCLCK_400_200
|
|
beq 3f
|
|
cmp r1, #MSAR_ARMDDRCLCK_600_200
|
|
beq 3f
|
|
cmp r1, #MSAR_ARMDDRCLCK_800_200
|
|
beq 3f
|
|
|
|
ldr r6, =0
|
|
|
|
3:
|
|
/* Use R3 as the base for DRAM registers */
|
|
add r3, r4, #0x01000
|
|
|
|
ldr r2, [r3, #0x484]
|
|
orr r2, r2, r6
|
|
str r2, [r3, #0x484]
|
|
|
|
/* enable for 2 GB DDR; detection should find out real amount */
|
|
sub r6, r6, r6
|
|
str r6, [r3, #0x500]
|
|
ldr r6, =0x7fff0001
|
|
str r6, [r3, #0x504]
|
|
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
/* Return to U-Boot via saved link register */
|
|
mov pc, lr
|