mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-13 14:53:06 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
219 lines
5.6 KiB
C
219 lines
5.6 KiB
C
/*
|
|
* (C) Copyright 2010
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/ppc440.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <i2c.h>
|
|
#include <mtd/cfi_flash.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <asm/mmu.h>
|
|
#include <asm/4xx_pcie.h>
|
|
#include <asm/ppc4xx-gpio.h>
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* Setup the interrupt controller polarities, triggers, etc.
|
|
*/
|
|
mtdcr(UIC0SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC0ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
|
|
mtdcr(UIC0PR, 0xffffffff); /* per ref-board manual */
|
|
mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */
|
|
mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC0SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr(UIC1SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC1ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC1CR, 0x00000000); /* all non-critical */
|
|
mtdcr(UIC1PR, 0x7fffffff); /* per ref-board manual */
|
|
mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */
|
|
mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC1SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr(UIC2SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC2ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC2CR, 0x00000000); /* all non-critical */
|
|
mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */
|
|
mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */
|
|
mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC2SR, 0xffffffff); /* clear all */
|
|
|
|
mtdcr(UIC3SR, 0xffffffff); /* clear all */
|
|
mtdcr(UIC3ER, 0x00000000); /* disable all */
|
|
mtdcr(UIC3CR, 0x00000000); /* all non-critical */
|
|
mtdcr(UIC3PR, 0xffffffff); /* per ref-board manual */
|
|
mtdcr(UIC3TR, 0x00000000); /* per ref-board manual */
|
|
mtdcr(UIC3VR, 0x00000000); /* int31 highest, base=0x000 */
|
|
mtdcr(UIC3SR, 0xffffffff); /* clear all */
|
|
|
|
/*
|
|
* Configure PFC (Pin Function Control) registers
|
|
* enable GPIO 49-63
|
|
* UART0: 4 pins
|
|
*/
|
|
mtsdr(SDR0_PFC0, 0x00007fff);
|
|
mtsdr(SDR0_PFC1, 0x00040000);
|
|
|
|
/* Enable PCI host functionality in SDR0_PCI0 */
|
|
mtsdr(SDR0_PCI0, 0xe0000000);
|
|
|
|
mtsdr(SDR0_SRST1, 0); /* Pull AHB out of reset default=1 */
|
|
|
|
/* Setup PLB4-AHB bridge based on the system address map */
|
|
mtdcr(AHB_TOP, 0x8000004B);
|
|
mtdcr(AHB_BOT, 0x8000004B);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char buf[64];
|
|
int i = getenv_f("serial#", buf, sizeof(buf));
|
|
|
|
printf("Board: T3CORP");
|
|
|
|
if (i > 0) {
|
|
puts(", serial# ");
|
|
puts(buf);
|
|
}
|
|
putc('\n');
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_early_init_r(void)
|
|
{
|
|
/*
|
|
* T3CORP has 64MBytes of NOR flash (Spansion 29GL512), but the
|
|
* boot EBC mapping only supports a maximum of 16MBytes
|
|
* (4.ff00.0000 - 4.ffff.ffff).
|
|
* To solve this problem, the flash has to get remapped to another
|
|
* EBC address which accepts bigger regions:
|
|
*
|
|
* 0xfn00.0000 -> 4.cn00.0000
|
|
*/
|
|
|
|
/* Remap the NOR flash to 0xcn00.0000 ... 0xcfff.ffff */
|
|
mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L | EBC_BXCR_BS_64MB |
|
|
EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
|
|
|
|
/* Remove TLB entry of boot EBC mapping */
|
|
remove_tlb(CONFIG_SYS_BOOT_BASE_ADDR, 16 << 20);
|
|
|
|
/* Add TLB entry for 0xfn00.0000 -> 0x4.cn00.0000 */
|
|
program_tlb(CONFIG_SYS_FLASH_BASE_PHYS, CONFIG_SYS_FLASH_BASE,
|
|
CONFIG_SYS_FLASH_SIZE, TLB_WORD2_I_ENABLE);
|
|
|
|
/*
|
|
* Now accessing of the whole 64Mbytes of NOR flash at virtual address
|
|
* 0xfc00.0000 is possible
|
|
*/
|
|
|
|
/*
|
|
* Clear potential errors resulting from auto-calibration.
|
|
* If not done, then we could get an interrupt later on when
|
|
* exceptions are enabled.
|
|
*/
|
|
set_mcsr(get_mcsr());
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r(void)
|
|
{
|
|
u32 sdr0_srst1 = 0;
|
|
u32 eth_cfg;
|
|
|
|
/*
|
|
* Set EMAC mode/configuration (GMII, SGMII, RGMII...).
|
|
* This is board specific, so let's do it here.
|
|
*/
|
|
mfsdr(SDR0_ETH_CFG, eth_cfg);
|
|
/* disable SGMII mode */
|
|
eth_cfg &= ~(SDR0_ETH_CFG_SGMII2_ENABLE |
|
|
SDR0_ETH_CFG_SGMII1_ENABLE |
|
|
SDR0_ETH_CFG_SGMII0_ENABLE);
|
|
/* Set the for 2 RGMII mode */
|
|
/* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */
|
|
eth_cfg &= ~SDR0_ETH_CFG_GMC0_BRIDGE_SEL;
|
|
eth_cfg &= ~SDR0_ETH_CFG_GMC1_BRIDGE_SEL;
|
|
mtsdr(SDR0_ETH_CFG, eth_cfg);
|
|
|
|
/*
|
|
* The AHB Bridge core is held in reset after power-on or reset
|
|
* so enable it now
|
|
*/
|
|
mfsdr(SDR0_SRST1, sdr0_srst1);
|
|
sdr0_srst1 &= ~SDR0_SRST1_AHB;
|
|
mtsdr(SDR0_SRST1, sdr0_srst1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_pcie_last(void)
|
|
{
|
|
/*
|
|
* Only PCIe0 for now, PCIe1 hangs on this board
|
|
*/
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Board specific WRDTR and CLKTR values used by the auto-
|
|
* calibration code (4xx_ibm_ddr2_autocalib.c).
|
|
*/
|
|
static struct sdram_timing board_scan_options[] = {
|
|
{1, 2},
|
|
{-1, -1}
|
|
};
|
|
|
|
struct sdram_timing *ddr_scan_option(struct sdram_timing *default_val)
|
|
{
|
|
return board_scan_options;
|
|
}
|
|
|
|
/*
|
|
* Accessor functions replacing the "weak" functions in
|
|
* drivers/mtd/cfi_flash.c
|
|
*
|
|
* The NOR flash devices "behind" the FPGA's (Xilinx DS617)
|
|
* can only be read correctly in 16bit mode. We need to emulate
|
|
* 8bit and 32bit reads here in the board specific code.
|
|
*/
|
|
u8 flash_read8(void *addr)
|
|
{
|
|
u16 val = __raw_readw((void *)((u32)addr & ~1));
|
|
|
|
if ((u32)addr & 1)
|
|
return val;
|
|
|
|
return val >> 8;
|
|
}
|
|
|
|
u32 flash_read32(void *addr)
|
|
{
|
|
return (__raw_readw(addr) << 16) | __raw_readw((void *)((u32)addr + 2));
|
|
}
|
|
|
|
void flash_cmd_reset(flash_info_t *info)
|
|
{
|
|
/*
|
|
* FLASH at address CONFIG_SYS_FLASH_BASE is a Spansion chip and
|
|
* needs the Spansion type reset commands. The other flash chip
|
|
* is located behind a FPGA (Xilinx DS617) and needs the Intel type
|
|
* reset command.
|
|
*/
|
|
if (info->start[0] == CONFIG_SYS_FLASH_BASE)
|
|
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
|
|
else
|
|
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
|
|
}
|