mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-21 02:33:07 +00:00
d1998a9fde
This name is far too long. Rename it to remove the 'data' bits. This makes it consistent with the platdata->plat rename. Signed-off-by: Simon Glass <sjg@chromium.org>
231 lines
6.1 KiB
C
231 lines
6.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2009
|
|
* Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
|
|
*/
|
|
|
|
#ifndef __DW_I2C_H_
|
|
#define __DW_I2C_H_
|
|
|
|
#include <clk.h>
|
|
#include <i2c.h>
|
|
#include <reset.h>
|
|
#include <linux/bitops.h>
|
|
|
|
struct i2c_regs {
|
|
u32 ic_con; /* 0x00 */
|
|
u32 ic_tar; /* 0x04 */
|
|
u32 ic_sar; /* 0x08 */
|
|
u32 ic_hs_maddr; /* 0x0c */
|
|
u32 ic_cmd_data; /* 0x10 */
|
|
u32 ic_ss_scl_hcnt; /* 0x14 */
|
|
u32 ic_ss_scl_lcnt; /* 0x18 */
|
|
u32 ic_fs_scl_hcnt; /* 0x1c */
|
|
u32 ic_fs_scl_lcnt; /* 0x20 */
|
|
u32 ic_hs_scl_hcnt; /* 0x24 */
|
|
u32 ic_hs_scl_lcnt; /* 0x28 */
|
|
u32 ic_intr_stat; /* 0x2c */
|
|
u32 ic_intr_mask; /* 0x30 */
|
|
u32 ic_raw_intr_stat; /* 0x34 */
|
|
u32 ic_rx_tl; /* 0x38 */
|
|
u32 ic_tx_tl; /* 0x3c */
|
|
u32 ic_clr_intr; /* 0x40 */
|
|
u32 ic_clr_rx_under; /* 0x44 */
|
|
u32 ic_clr_rx_over; /* 0x48 */
|
|
u32 ic_clr_tx_over; /* 0x4c */
|
|
u32 ic_clr_rd_req; /* 0x50 */
|
|
u32 ic_clr_tx_abrt; /* 0x54 */
|
|
u32 ic_clr_rx_done; /* 0x58 */
|
|
u32 ic_clr_activity; /* 0x5c */
|
|
u32 ic_clr_stop_det; /* 0x60 */
|
|
u32 ic_clr_start_det; /* 0x64 */
|
|
u32 ic_clr_gen_call; /* 0x68 */
|
|
u32 ic_enable; /* 0x6c */
|
|
u32 ic_status; /* 0x70 */
|
|
u32 ic_txflr; /* 0x74 */
|
|
u32 ic_rxflr; /* 0x78 */
|
|
u32 ic_sda_hold; /* 0x7c */
|
|
u32 ic_tx_abrt_source; /* 0x80 */
|
|
u32 slv_data_nak_only;
|
|
u32 dma_cr;
|
|
u32 dma_tdlr;
|
|
u32 dma_rdlr;
|
|
u32 sda_setup;
|
|
u32 ack_general_call;
|
|
u32 ic_enable_status; /* 0x9c */
|
|
u32 fs_spklen;
|
|
u32 hs_spklen;
|
|
u32 clr_restart_det;
|
|
u8 reserved[0xf4 - 0xac];
|
|
u32 comp_param1; /* 0xf4 */
|
|
u32 comp_version;
|
|
u32 comp_type;
|
|
};
|
|
|
|
#define IC_CLK 166666666
|
|
#define NANO_TO_KILO 1000000
|
|
|
|
/* High and low times in different speed modes (in ns) */
|
|
#define MIN_SS_SCL_HIGHTIME 4000
|
|
#define MIN_SS_SCL_LOWTIME 4700
|
|
#define MIN_FS_SCL_HIGHTIME 600
|
|
#define MIN_FS_SCL_LOWTIME 1300
|
|
#define MIN_FP_SCL_HIGHTIME 260
|
|
#define MIN_FP_SCL_LOWTIME 500
|
|
#define MIN_HS_SCL_HIGHTIME 60
|
|
#define MIN_HS_SCL_LOWTIME 160
|
|
|
|
/* Worst case timeout for 1 byte is kept as 2ms */
|
|
#define I2C_BYTE_TO (CONFIG_SYS_HZ/500)
|
|
#define I2C_STOPDET_TO (CONFIG_SYS_HZ/500)
|
|
#define I2C_BYTE_TO_BB (I2C_BYTE_TO * 16)
|
|
|
|
/* i2c control register definitions */
|
|
#define IC_CON_SD 0x0040
|
|
#define IC_CON_RE 0x0020
|
|
#define IC_CON_10BITADDRMASTER 0x0010
|
|
#define IC_CON_10BITADDR_SLAVE 0x0008
|
|
#define IC_CON_SPD_MSK 0x0006
|
|
#define IC_CON_SPD_SS 0x0002
|
|
#define IC_CON_SPD_FS 0x0004
|
|
#define IC_CON_SPD_HS 0x0006
|
|
#define IC_CON_MM 0x0001
|
|
|
|
/* i2c target address register definitions */
|
|
#define TAR_ADDR 0x0050
|
|
|
|
/* i2c slave address register definitions */
|
|
#define IC_SLAVE_ADDR 0x0002
|
|
|
|
/* i2c data buffer and command register definitions */
|
|
#define IC_CMD 0x0100
|
|
#define IC_STOP 0x0200
|
|
|
|
/* i2c interrupt status register definitions */
|
|
#define IC_GEN_CALL 0x0800
|
|
#define IC_START_DET 0x0400
|
|
#define IC_STOP_DET 0x0200
|
|
#define IC_ACTIVITY 0x0100
|
|
#define IC_RX_DONE 0x0080
|
|
#define IC_TX_ABRT 0x0040
|
|
#define IC_RD_REQ 0x0020
|
|
#define IC_TX_EMPTY 0x0010
|
|
#define IC_TX_OVER 0x0008
|
|
#define IC_RX_FULL 0x0004
|
|
#define IC_RX_OVER 0x0002
|
|
#define IC_RX_UNDER 0x0001
|
|
|
|
/* fifo threshold register definitions */
|
|
#define IC_TL0 0x00
|
|
#define IC_TL1 0x01
|
|
#define IC_TL2 0x02
|
|
#define IC_TL3 0x03
|
|
#define IC_TL4 0x04
|
|
#define IC_TL5 0x05
|
|
#define IC_TL6 0x06
|
|
#define IC_TL7 0x07
|
|
#define IC_RX_TL IC_TL0
|
|
#define IC_TX_TL IC_TL0
|
|
|
|
/* i2c enable register definitions */
|
|
#define IC_ENABLE_0B 0x0001
|
|
|
|
/* i2c status register definitions */
|
|
#define IC_STATUS_SA 0x0040
|
|
#define IC_STATUS_MA 0x0020
|
|
#define IC_STATUS_RFF 0x0010
|
|
#define IC_STATUS_RFNE 0x0008
|
|
#define IC_STATUS_TFE 0x0004
|
|
#define IC_STATUS_TFNF 0x0002
|
|
#define IC_STATUS_ACT 0x0001
|
|
|
|
#define DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH (BIT(2) | BIT(3))
|
|
#define DW_IC_COMP_PARAM_1_SPEED_MODE_MASK (BIT(2) | BIT(3))
|
|
|
|
/**
|
|
* struct dw_scl_sda_cfg - I2C timing configuration
|
|
*
|
|
* @ss_hcnt: Standard speed high time in ns
|
|
* @fs_hcnt: Fast speed high time in ns
|
|
* @hs_hcnt: High speed high time in ns
|
|
* @ss_lcnt: Standard speed low time in ns
|
|
* @fs_lcnt: Fast speed low time in ns
|
|
* @hs_lcnt: High speed low time in ns
|
|
* @sda_hold: SDA hold time
|
|
*/
|
|
struct dw_scl_sda_cfg {
|
|
u32 ss_hcnt;
|
|
u32 fs_hcnt;
|
|
u32 hs_hcnt;
|
|
u32 ss_lcnt;
|
|
u32 fs_lcnt;
|
|
u32 hs_lcnt;
|
|
u32 sda_hold;
|
|
};
|
|
|
|
/**
|
|
* struct dw_i2c_speed_config - timings to use for a particular speed
|
|
*
|
|
* This holds calculated values to be written to the I2C controller. Each value
|
|
* is represented as a number of IC clock cycles.
|
|
*
|
|
* @scl_lcnt: Low count value for SCL
|
|
* @scl_hcnt: High count value for SCL
|
|
* @sda_hold: Data hold count
|
|
* @speed_mode: Speed mode being used
|
|
*/
|
|
struct dw_i2c_speed_config {
|
|
/* SCL high and low period count */
|
|
u16 scl_lcnt;
|
|
u16 scl_hcnt;
|
|
u32 sda_hold;
|
|
enum i2c_speed_mode speed_mode;
|
|
};
|
|
|
|
/**
|
|
* struct dw_i2c - private information for the bus
|
|
*
|
|
* @regs: Registers pointer
|
|
* @scl_sda_cfg: Deprecated information for x86 (should move to device tree)
|
|
* @resets: Resets for the I2C controller
|
|
* @scl_rise_time_ns: Configured SCL rise time in nanoseconds
|
|
* @scl_fall_time_ns: Configured SCL fall time in nanoseconds
|
|
* @sda_hold_time_ns: Configured SDA hold time in nanoseconds
|
|
* @has_spk_cnt: true if the spike-count register is present
|
|
* @clk: Clock input to the I2C controller
|
|
*/
|
|
struct dw_i2c {
|
|
struct i2c_regs *regs;
|
|
struct dw_scl_sda_cfg *scl_sda_cfg;
|
|
struct reset_ctl_bulk resets;
|
|
u32 scl_rise_time_ns;
|
|
u32 scl_fall_time_ns;
|
|
u32 sda_hold_time_ns;
|
|
bool has_spk_cnt;
|
|
#if CONFIG_IS_ENABLED(CLK)
|
|
struct clk clk;
|
|
#endif
|
|
struct dw_i2c_speed_config config;
|
|
};
|
|
|
|
extern const struct dm_i2c_ops designware_i2c_ops;
|
|
|
|
int designware_i2c_probe(struct udevice *bus);
|
|
int designware_i2c_remove(struct udevice *dev);
|
|
int designware_i2c_of_to_plat(struct udevice *bus);
|
|
|
|
/**
|
|
* dw_i2c_gen_speed_config() - Calculate config info from requested speed
|
|
*
|
|
* Calculate the speed config from the given @speed_hz and return it so that
|
|
* it can be incorporated in ACPI tables
|
|
*
|
|
* @dev: I2C bus to check
|
|
* @speed_hz: Requested speed in Hz
|
|
* @config: Returns config to use for that speed
|
|
* @return 0 if OK, -ve on error
|
|
*/
|
|
int dw_i2c_gen_speed_config(const struct udevice *dev, int speed_hz,
|
|
struct dw_i2c_speed_config *config);
|
|
|
|
#endif /* __DW_I2C_H_ */
|