u-boot/board/prodrive/p3p440/p3p440.c
Wolfgang Denk 3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00

177 lines
4.5 KiB
C

/*
* (C) Copyright 2005
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/processor.h>
#include <command.h>
#include "p3p440.h"
DECLARE_GLOBAL_DATA_PTR;
void set_led(int color)
{
switch (color) {
case LED_OFF:
out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_LED_GREEN & ~CONFIG_SYS_LED_RED);
break;
case LED_GREEN:
out32(GPIO0_OR, (in32(GPIO0_OR) | CONFIG_SYS_LED_GREEN) & ~CONFIG_SYS_LED_RED);
break;
case LED_RED:
out32(GPIO0_OR, (in32(GPIO0_OR) | CONFIG_SYS_LED_RED) & ~CONFIG_SYS_LED_GREEN);
break;
case LED_ORANGE:
out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_LED_GREEN | CONFIG_SYS_LED_RED);
break;
}
}
static int is_monarch(void)
{
out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_GPIO_RDY);
udelay(1000);
if (in32(GPIO0_IR) & CONFIG_SYS_MONARCH_IO)
return 0;
else
return 1;
}
static void wait_for_pci_ready(void)
{
/*
* Configure EREADY_IO as input
*/
out32(GPIO0_TCR, in32(GPIO0_TCR) & ~CONFIG_SYS_EREADY_IO);
udelay(1000);
for (;;) {
if (in32(GPIO0_IR) & CONFIG_SYS_EREADY_IO)
return;
}
}
int board_early_init_f(void)
{
uint reg;
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
mtdcr(EBC0_CFGADDR, EBC0_CFG);
reg = mfdcr(EBC0_CFGDATA);
mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* Setup pin multiplexing (GPIO/IRQ...)
*-------------------------------------------------------------------*/
mtdcr(CPC0_GPIO, 0x03F01F80);
out32(GPIO0_ODR, 0x00000000); /* no open drain pins */
out32(GPIO0_TCR, CONFIG_SYS_GPIO_RDY | CONFIG_SYS_EREADY_IO | CONFIG_SYS_LED_RED | CONFIG_SYS_LED_GREEN);
out32(GPIO0_OR, CONFIG_SYS_GPIO_RDY);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
mtdcr(UIC0SR, 0xffffffff); /* clear all */
mtdcr(UIC0ER, 0x00000000); /* disable all */
mtdcr(UIC0CR, 0x00000001); /* UIC1 crit is critical */
mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
mtdcr(UIC0SR, 0xffffffff); /* clear all */
mtdcr(UIC1SR, 0xffffffff); /* clear all */
mtdcr(UIC1ER, 0x00000000); /* disable all */
mtdcr(UIC1CR, 0x00000000); /* all non-critical */
mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
mtdcr(UIC1SR, 0xffffffff); /* clear all */
return 0;
}
int checkboard(void)
{
char buf[64];
int i = getenv_f("serial#", buf, sizeof(buf));
printf("Board: P3P440");
if (i > 0) {
puts(", serial# ");
puts(buf);
}
if (is_monarch()) {
puts(", Monarch");
} else {
puts(", None-Monarch");
}
putc('\n');
return (0);
}
int misc_init_r (void)
{
/*
* Adjust flash start and offset to detected values
*/
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
/*
* Check if only one FLASH bank is available
*/
if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
mtebc(PB1CR, 0); /* disable cs */
mtebc(PB1AP, 0);
mtebc(PB2CR, 0); /* disable cs */
mtebc(PB2AP, 0);
mtebc(PB3CR, 0); /* disable cs */
mtebc(PB3AP, 0);
}
return 0;
}
/*************************************************************************
* Override weak is_pci_host()
*
* This routine is called to determine if a pci scan should be
* performed. With various hardware environments (especially cPCI and
* PPMC) it's insufficient to depend on the state of the arbiter enable
* bit in the strap register, or generic host/adapter assumptions.
*
* Rather than hard-code a bad assumption in the general 440 code, the
* 440 pci code requires the board to decide at runtime.
*
* Return 0 for adapter mode, non-zero for host (monarch) mode.
*
*
************************************************************************/
#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
if (is_monarch()) {
wait_for_pci_ready();
return 1; /* return 1 for host controller */
} else {
return 0; /* return 0 for adapter controller */
}
}
#endif /* defined(CONFIG_PCI) */