mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 17:07:38 +00:00
c72a23701b
If PMIC is not probed successfully, it is still OK to boot with default configuration although power is not optimized. Default voltage of SW1A/SW1B is 1.1V/1.0V for PC32PF3000A1EP on pico according to table 42 of spec of PF3000 ver 9.0. Default mode of SW1A/SW1B is APS as expected(table 47). Signed-off-by: Jun Nie <jun.nie@linaro.org>
342 lines
9.5 KiB
C
342 lines
9.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2017 NXP Semiconductors
|
|
*/
|
|
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/mx7-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <asm/io.h>
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <usb.h>
|
|
#include <power/pmic.h>
|
|
#include <power/pfuze3000_pmic.h>
|
|
#include "../../freescale/common/pfuze.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \
|
|
PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
|
|
#define ENET_PAD_CTRL_MII (PAD_CTL_DSE_3P3V_32OHM)
|
|
|
|
#define ENET_RX_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
|
|
PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
|
|
|
|
|
|
#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
|
|
PAD_CTL_DSE_3P3V_49OHM)
|
|
|
|
#define LCD_SYNC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
|
|
PAD_CTL_DSE_3P3V_196OHM)
|
|
|
|
#ifdef CONFIG_SYS_I2C_MXC
|
|
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
|
|
|
|
/* I2C4 for PMIC */
|
|
static struct i2c_pads_info i2c_pad_info4 = {
|
|
.scl = {
|
|
.i2c_mode = MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL | PC,
|
|
.gpio_mode = MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 | PC,
|
|
.gp = IMX_GPIO_NR(6, 16),
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA | PC,
|
|
.gpio_mode = MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17 | PC,
|
|
.gp = IMX_GPIO_NR(6, 17),
|
|
},
|
|
};
|
|
#endif
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
/* Subtract the defined OPTEE runtime firmware length */
|
|
#ifdef CONFIG_OPTEE_TZDRAM_SIZE
|
|
gd->ram_size -= CONFIG_OPTEE_TZDRAM_SIZE;
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_POWER
|
|
#define I2C_PMIC 3
|
|
int power_init_board(void)
|
|
{
|
|
struct pmic *p;
|
|
int ret;
|
|
unsigned int reg, rev_id;
|
|
|
|
ret = power_pfuze3000_init(I2C_PMIC);
|
|
if (ret)
|
|
return ret;
|
|
|
|
p = pmic_get("PFUZE3000");
|
|
ret = pmic_probe(p);
|
|
if (ret) {
|
|
printf("Warning: Cannot find PMIC PFUZE3000\n");
|
|
printf("\tPower consumption is not optimized.\n");
|
|
return 0;
|
|
}
|
|
|
|
pmic_reg_read(p, PFUZE3000_DEVICEID, ®);
|
|
pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
|
|
printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
|
|
|
|
/* disable Low Power Mode during standby mode */
|
|
pmic_reg_read(p, PFUZE3000_LDOGCTL, ®);
|
|
reg |= 0x1;
|
|
pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
|
|
|
|
/* SW1A/1B mode set to APS/APS */
|
|
reg = 0x8;
|
|
pmic_reg_write(p, PFUZE3000_SW1AMODE, reg);
|
|
pmic_reg_write(p, PFUZE3000_SW1BMODE, reg);
|
|
|
|
/* SW1A/1B standby voltage set to 1.025V */
|
|
reg = 0xd;
|
|
pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
|
|
pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
|
|
|
|
/* decrease SW1B normal voltage to 0.975V */
|
|
pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®);
|
|
reg &= ~0x1f;
|
|
reg |= PFUZE3000_SW1AB_SETP(975);
|
|
pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static iomux_v3_cfg_t const wdog_pads[] = {
|
|
MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const uart5_pads[] = {
|
|
MX7D_PAD_I2C4_SCL__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX7D_PAD_I2C4_SDA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
static iomux_v3_cfg_t const fec1_pads[] = {
|
|
MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
|
|
MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
|
|
MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
|
|
MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
|
|
MX7D_PAD_SD3_STROBE__GPIO6_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
#define FEC1_RST_GPIO IMX_GPIO_NR(6, 11)
|
|
|
|
static void setup_iomux_fec(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
|
|
gpio_request(FEC1_RST_GPIO, "phy_rst");
|
|
gpio_direction_output(FEC1_RST_GPIO, 0);
|
|
udelay(500);
|
|
gpio_set_value(FEC1_RST_GPIO, 1);
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
setup_iomux_fec();
|
|
|
|
return fecmxc_initialize_multi(bis, 0,
|
|
CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
|
|
}
|
|
|
|
static int setup_fec(void)
|
|
{
|
|
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
|
|
= (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
|
|
|
|
/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17] */
|
|
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
|
|
(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
|
|
IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
|
|
|
|
return set_clk_enet(ENET_125MHZ);
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
unsigned short val;
|
|
|
|
/* To enable AR8035 ouput a 125MHz clk from CLK_25M */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
|
|
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
|
|
val &= 0xffe7;
|
|
val |= 0x18;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
|
|
|
|
/* introduce tx clock delay */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
|
|
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
|
|
val |= 0x0100;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
|
|
#ifdef CONFIG_SYS_I2C_MXC
|
|
setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_VIDEO_MXS
|
|
static iomux_v3_cfg_t const lcd_pads[] = {
|
|
MX7D_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_ENABLE__LCD_ENABLE | MUX_PAD_CTRL(LCD_SYNC_PAD_CTRL),
|
|
MX7D_PAD_LCD_HSYNC__LCD_HSYNC | MUX_PAD_CTRL(LCD_SYNC_PAD_CTRL),
|
|
MX7D_PAD_LCD_VSYNC__LCD_VSYNC | MUX_PAD_CTRL(LCD_SYNC_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA00__LCD_DATA0 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA01__LCD_DATA1 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA02__LCD_DATA2 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA03__LCD_DATA3 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA04__LCD_DATA4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA05__LCD_DATA5 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA06__LCD_DATA6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA07__LCD_DATA7 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA08__LCD_DATA8 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA09__LCD_DATA9 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA10__LCD_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA11__LCD_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA12__LCD_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA13__LCD_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA14__LCD_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA15__LCD_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA16__LCD_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA17__LCD_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA18__LCD_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA19__LCD_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA20__LCD_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA21__LCD_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA22__LCD_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_LCD_DATA23__LCD_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_GPIO1_IO06__GPIO1_IO6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
|
|
MX7D_PAD_GPIO1_IO11__GPIO1_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
void setup_lcd(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
|
|
gpio_request(IMX_GPIO_NR(1, 11), "lcd_brightness");
|
|
gpio_request(IMX_GPIO_NR(1, 6), "lcd_enable");
|
|
/* Set Brightness to high */
|
|
gpio_direction_output(IMX_GPIO_NR(1, 11) , 1);
|
|
/* Set LCD enable to high */
|
|
gpio_direction_output(IMX_GPIO_NR(1, 6) , 1);
|
|
}
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
#ifdef CONFIG_VIDEO_MXS
|
|
setup_lcd();
|
|
#endif
|
|
#ifdef CONFIG_FEC_MXC
|
|
setup_fec();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
|
|
|
|
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
|
|
|
|
set_wdog_reset(wdog);
|
|
|
|
/*
|
|
* Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
|
|
* since we use PMIC_PWRON to reset the board.
|
|
*/
|
|
clrsetbits_le16(&wdog->wcr, 0, 0x10);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: i.MX7D PICOSOM\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static iomux_v3_cfg_t const usb_otg2_pads[] = {
|
|
MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
int board_ehci_hcd_init(int port)
|
|
{
|
|
switch (port) {
|
|
case 0:
|
|
break;
|
|
case 1:
|
|
imx_iomux_v3_setup_multiple_pads(usb_otg2_pads,
|
|
ARRAY_SIZE(usb_otg2_pads));
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
int board_usb_phy_mode(int port)
|
|
{
|
|
switch (port) {
|
|
case 0:
|
|
return USB_INIT_DEVICE;
|
|
case 1:
|
|
return USB_INIT_HOST;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|