u-boot/configs/display5_defconfig
Lukasz Majewski 3201e5b444 imx: defconfig: Enable CONFIG_SPL_FORCE_MMC_BOOT on display5
After the following commit:
commit 772b55723b ("imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC
boot on falcon mode")
it is possible to set the CONFIG_SPL_FORCE_MMC_BOOT flag, which allows
using MMC device as boot device regardless of the device used by Boot ROM
(FBL) as the first boot medium.

Display5 board needs this flag set to allow falcon boot from eMMC device.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03 17:04:16 +01:00

116 lines
2.9 KiB
Text

CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_SYS_TEXT_BASE=0x17800000
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x1000
CONFIG_MX6_DDRCAL=y
CONFIG_TARGET_DISPLAY5=y
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y
CONFIG_SYS_BOOTCOUNT_ADDR=0x020CC068
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_SPL_TEXT_BASE=0x00908000
CONFIG_FIT=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_MISC_INIT_R=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_SPL_BOOTCOUNT_LIMIT=y
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_DMA_SUPPORT=y
CONFIG_SPL_ENV_SUPPORT=y
CONFIG_SPL_SAVEENV=y
CONFIG_SPL_I2C_SUPPORT=y
CONFIG_SPL_FORCE_MMC_BOOT=y
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x20000
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="display5 > "
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_ELF is not set
CONFIG_CMD_ASKENV=y
CONFIG_CRC32_VERIFY=y
CONFIG_CMD_EEPROM=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
CONFIG_CMD_WDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_PMIC=y
CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nor0=02008000.spi.1"
CONFIG_MTDPARTS_DEFAULT="mtdparts=02008000.spi.1:128k(SPL),1m(u-boot),64k(env1),64k(env2),4m(swu-kernel),16m(swu-initramfs),1m(factory),-(reserved)"
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="imx6q-display5"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_I2C_DEFAULT_BUS_NUMBER=0x2
CONFIG_SYS_I2C_MXC=y
CONFIG_SYS_I2C_MXC_I2C1=y
CONFIG_SYS_I2C_MXC_I2C2=y
CONFIG_SYS_I2C_MXC_I2C3=y
CONFIG_MISC=y
CONFIG_I2C_EEPROM=y
CONFIG_SYS_I2C_EEPROM_ADDR=0x50
CONFIG_SYS_I2C_EEPROM_BUS=2
CONFIG_SYS_EEPROM_SIZE=32768
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_USDHC=y
CONFIG_MTD_DEVICE=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=50000000
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHYLIB=y
CONFIG_PHY_MARVELL=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_MXC_UART=y
CONFIG_SPI=y
CONFIG_MXC_SPI=y
CONFIG_WATCHDOG_TIMEOUT_MSECS=15000
CONFIG_SYSRESET=y
CONFIG_SYSRESET_WATCHDOG=y
CONFIG_I2C_EDID=y
CONFIG_IMX_WATCHDOG=y