Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-21 02:33:07 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/myir/mys_6ulx
History
Simon Glass 401d1c4f5d common: Drop asm/global_data.h from common header 
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
..
Kconfig imx: Add MYiR Tech MYS-6ULX support 2020-08-03 17:03:57 +02:00
MAINTAINERS imx: Add MYiR Tech MYS-6ULX support 2020-08-03 17:03:57 +02:00
Makefile imx: Add MYiR Tech MYS-6ULX support 2020-08-03 17:03:57 +02:00
mys_6ulx.c common: Drop asm/global_data.h from common header 2021-02-02 15:33:42 -05:00
README imx: Add MYiR Tech MYS-6ULX support 2020-08-03 17:03:57 +02:00
spl.c imx: Add MYiR Tech MYS-6ULX support 2020-08-03 17:03:57 +02:00

README 

How to use U-Boot on MYiR MYS-6ULX Single Board Computer
--------------------------------------------------------

- Configure and build U-Boot for MYS-6ULX iMX6ULL:

    $ make mrproper
    $ make myir_mys_6ulx_defconfig
    $ make

  This will generate SPL and u-boot-dtb.img images.

Boot from MMC/SD:
- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:

    $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync

- Boot mode settings:

  Boot switch position: SW1 -> 0
			SW2 -> 1
			SW3 -> 0
			SW4 -> 1

Boot from NAND:
- Boot the board using SD/MMC or Serial download and load the SPL into memory
either from SD/MMC or TFTP.

Default MTD layout is 512k(spl),1m(uboot),1m(uboot-dup),-(ubi)

Flash SPL to NAND from SD/MMC,

    $ ext4load mmc 0:2 $loadaddr SPL
    $ nand erase.part spl
    $ nandbcb init $loadaddr 0x0 $filesize

Flash u-boot proper to NAND from SD/MMC,

    $ ext4load mmc 0:2 $loadaddr u-boot-dtb.img
    $ nand erase.part uboot
    $ nand write $loadaddr uboot $filesize

- Boot mode settings:

  Boot switch position: SW1 -> 1
			SW2 -> 0
			SW3 -> 0
			SW4 -> 1

- Connect the Serial cable to UART0 and the PC for the console.

- Reset the board using and U-Boot should boot from NAND.