mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-08 22:24:32 +00:00
90526e9fba
Move this header out of the common header. Network support is used in quite a few places but it still does not warrant blanket inclusion. Note that this net.h header itself has quite a lot in it. It could be split into the driver-mode support, functions, structures, checksumming, etc. Signed-off-by: Simon Glass <sjg@chromium.org>
118 lines
3.1 KiB
C
118 lines
3.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define ETH_PHY_CTRL_REG 0
|
|
#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
|
|
#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT)
|
|
|
|
/*
|
|
* Those values and defines are taken from the Marvell U-Boot version
|
|
* "u-boot-2011.12-2014_T1.0" for the board rd78460gp aka
|
|
* "RD-AXP-GP rev 1.0".
|
|
*
|
|
* GPPs
|
|
* MPP# NAME IN/OUT
|
|
* ----------------------------------------------
|
|
* 21 SW_Reset_ OUT
|
|
* 25 Phy_Int# IN
|
|
* 28 SDI_WP IN
|
|
* 29 SDI_Status IN
|
|
* 54-61 On GPP Connector ?
|
|
* 62 Switch Interrupt IN
|
|
* 63-65 Reserved from SW Board ?
|
|
* 66 SW_BRD connected IN
|
|
*/
|
|
#define RD_78460_GP_GPP_OUT_ENA_LOW (~(BIT(21) | BIT(20)))
|
|
#define RD_78460_GP_GPP_OUT_ENA_MID (~(BIT(26) | BIT(27)))
|
|
#define RD_78460_GP_GPP_OUT_ENA_HIGH (~(0x0))
|
|
|
|
#define RD_78460_GP_GPP_OUT_VAL_LOW (BIT(21) | BIT(20))
|
|
#define RD_78460_GP_GPP_OUT_VAL_MID (BIT(26) | BIT(27))
|
|
#define RD_78460_GP_GPP_OUT_VAL_HIGH 0x0
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* Configure MPP */
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x00);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x04);
|
|
writel(0x33000000, MVEBU_MPP_BASE + 0x08);
|
|
writel(0x11000000, MVEBU_MPP_BASE + 0x0c);
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x10);
|
|
writel(0x00221100, MVEBU_MPP_BASE + 0x14);
|
|
writel(0x00000003, MVEBU_MPP_BASE + 0x18);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x1c);
|
|
writel(0x00000000, MVEBU_MPP_BASE + 0x20);
|
|
|
|
/* Configure GPIO */
|
|
writel(RD_78460_GP_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
|
|
writel(RD_78460_GP_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
|
|
writel(RD_78460_GP_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
|
|
writel(RD_78460_GP_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
|
|
writel(RD_78460_GP_GPP_OUT_VAL_HIGH, MVEBU_GPIO2_BASE + 0x00);
|
|
writel(RD_78460_GP_GPP_OUT_ENA_HIGH, MVEBU_GPIO2_BASE + 0x04);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: Marvell DB-MV784MP-GP\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
cpu_eth_init(bis); /* Built in controller(s) come first */
|
|
return pci_eth_init(bis);
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
u16 reg;
|
|
|
|
/* Enable QSGMII AN */
|
|
/* Set page to 4 */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 4);
|
|
/* Enable AN */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x0, 0x1140);
|
|
/* Set page to 0 */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x16, 0);
|
|
|
|
/* Phy C_ANEG */
|
|
reg = phy_read(phydev, MDIO_DEVAD_NONE, 0x4);
|
|
reg |= 0x1E0;
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x4, reg);
|
|
|
|
/* Soft-Reset */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0, 0x9140);
|
|
|
|
/* Power up the phy */
|
|
reg = phy_read(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG);
|
|
reg &= ~(ETH_PHY_CTRL_POWER_DOWN_MASK);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, ETH_PHY_CTRL_REG, reg);
|
|
|
|
printf("88E1545 Initialized\n");
|
|
return 0;
|
|
}
|