u-boot/configs/at91sam9g10ek_dataflash_cs3_defconfig
Tom Rini a542e4307d Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_MAY_FAIL
   CONFIG_BOOTP_VENDOREX
   CONFIG_BOOTP_BOOTFILESIZE
   CONFIG_BOOTP_NISDOMAIN
   CONFIG_BOOTP_TIMEOFFSET

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-03 16:51:20 -05:00

60 lines
1.6 KiB
Text

CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x21f00000
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_ENV_SECT_SIZE=0x210
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9261ek"
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_BASE=0xfffff200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G10,SYS_USE_DATAFLASH_CS3"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="sf probe 0:3; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_PROMPT="U-Boot> "
# CONFIG_CMD_BDI is not set
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
# CONFIG_CMD_SOURCE is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_BOOTP_BOOTFILESIZE=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_GPIO=y
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_DATAFLASH=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_USB=y