mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-06 21:24:29 +00:00
02ee7a4aa5
Convert imx6sabresd ethernet to driver model to fix the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> |
||
---|---|---|
.. | ||
Kconfig | ||
MAINTAINERS | ||
Makefile | ||
mx6sabresd.c | ||
README |
How to use and build U-Boot on mx6sabresd ----------------------------------------- The following methods can be used for booting mx6sabresd boards: 1. Booting from SD card 2. Booting from eMMC 3. Booting via Falcon mode (SPL launches the kernel directly) 1. Booting from SD card via SPL ------------------------------- mx6sabresd_defconfig target supports mx6q/mx6dl/mx6qp sabresd variants. In order to build it: $ make mx6sabresd_defconfig $ make This will generate the SPL and u-boot-dtb.img binaries. - Flash the SPL binary into the SD card: $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync - Flash the u-boot-dtb.img binary into the SD card: $ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync 2. Booting from eMMC -------------------- $ make mx6sabresd_defconfig $ make This will generate the SPL and u-boot-dtb.img binaries. - Boot first from SD card as shown in the previous section In U-boot change the eMMC partition config: => mmc partconf 2 1 0 0 Mount the eMMC in the host PC: => ums 0 mmc 2 - Flash SPL and u-boot-dtb.img binaries into the eMMC: $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync $ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync Set SW6 to eMMC 8-bit boot: 11010110 3. Booting via Falcon mode -------------------------- $ make mx6sabresd_defconfig $ make This will generate the SPL image called SPL and the u-boot-dtb.img. - Flash the SPL image into the SD card: $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync - Flash the u-boot-dtb.img image into the SD card: $ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync Create a partition for root file system and extract it there: $ sudo tar xvf rootfs.tar.gz -C /media/root The SD card must have enough space for raw "args" and "kernel". To configure Falcon mode for the first time, on U-Boot do the following commands: - Setup the IP server: # setenv serverip <server_ip_address> - Download dtb file: # dhcp ${fdt_addr} imx6q-sabresd.dtb - Download kernel image: # dhcp ${loadaddr} uImage - Write kernel at 2MB offset: # mmc write ${loadaddr} 0x1000 0x4000 - Setup kernel bootargs: # setenv bootargs "console=ttymxc0,115200 root=/dev/mmcblk1p1 rootfstype=ext4 rootwait quiet rw" - Prepare args: # spl export fdt ${loadaddr} - ${fdt_addr} - Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors) # mmc write 18000000 0x800 0x800 - Press KEY_VOL_UP key, power up the board and then SPL binary will launch the kernel directly.