u-boot/include/configs/bf533-stamp.h
Mike Frysinger f7ce12cb65 Blackfin: convert BFIN_CPU to CONFIG_BFIN_CPU
Stop tying things to the processor that should be tied to other defines and
change BFIN_CPU to CONFIG_BFIN_CPU so that it can be used in the build
system to select the -mcpu option.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15 22:14:14 -04:00

452 lines
13 KiB
C

/*
* U-boot - Configuration file for BF533 STAMP board
*/
#ifndef __CONFIG_STAMP_H__
#define __CONFIG_STAMP_H__
#include <asm/blackfin-config-pre.h>
#define CONFIG_STAMP 1
#define CONFIG_RTC_BFIN 1
#define CONFIG_BF533 1
/*
* Boot Mode Set
* Blackfin can support several boot modes
*/
#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
/* Define the boot mode */
#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
#define CONFIG_PANIC_HANG 1
#define CONFIG_BFIN_CPU bf533-0.3
/* This sets the default state of the cache on U-Boot's boot */
#define CONFIG_ICACHE_ON
#define CONFIG_DCACHE_ON
/* Define where the uboot will be loaded by on-chip boot rom */
#define APP_ENTRY 0x00001000
/*
* Stringize definitions - needed for environmental settings
*/
#define STRINGIZE2(x) #x
#define STRINGIZE(x) STRINGIZE2(x)
/*
* Board settings
*/
#define CONFIG_DRIVER_SMC91111 1
#define CONFIG_SMC91111_BASE 0x20300300
/* FLASH/ETHERNET uses the same address range */
#define SHARED_RESOURCES 1
/* Is I2C bit-banged? */
#define CONFIG_SOFT_I2C 1
/*
* Software (bit-bang) I2C driver configuration
*/
#define PF_SCL PF3
#define PF_SDA PF2
/*
* Video splash screen support
*/
#define CONFIG_VIDEO 0
#define CONFIG_VDSP 1
/*
* Clock settings
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 11059200
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
/* 1=CLKIN/2 */
#define CONFIG_CLKIN_HALF 0
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
/* 1=bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
/* Values can range from 1-64 */
#define CONFIG_VCO_MULT 36
/* CONFIG_CCLK_DIV controls what the core clock divider is */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
/* Values can range from 2-65535 */
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
#define CONFIG_SPI_BAUD 2
#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#define CONFIG_SPI_BAUD_INITBLOCK 4
#endif
/*
* Network settings
*/
#if (CONFIG_DRIVER_SMC91111)
#if 0
#define CONFIG_MII
#endif
/* network support */
#define CONFIG_IPADDR 192.168.0.15
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_SERVERIP 192.168.0.2
#define CONFIG_HOSTNAME STAMP
#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
/* To remove hardcoding and enable MAC storage in EEPROM */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
#endif /* CONFIG_DRIVER_SMC91111 */
/*
* Flash settings
*/
#define CFG_FLASH_CFI /* The flash is CFI compatible */
#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_CFI_AMD_RESET
#define CFG_FLASH_BASE 0x20000000
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR 0x20004000
#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#define CFG_ENV_IS_IN_EEPROM 1
#define CFG_ENV_OFFSET 0x4000
#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
#endif
#define CFG_ENV_SIZE 0x2000
#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
#define ENV_IS_EMBEDDED
#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
/* JFFS Partition offset set */
#define CFG_JFFS2_FIRST_BANK 0
#define CFG_JFFS2_NUM_BANKS 1
/* 512k reserved for u-boot */
#define CFG_JFFS2_FIRST_SECTOR 11
/*
* following timeouts shall be used once the
* Flash real protection is enabled
*/
#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
/*
* SDRAM settings & memory map
*/
#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#endif
#define CFG_SDRAM_BASE 0x00000000
#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
#define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1)
#define CONFIG_LOADADDR 0x01000000
#define CFG_LOAD_ADDR CONFIG_LOADADDR
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000)
#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
/* Check to make sure everything fits in SDRAM */
#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE)
#error Memory Map does not fit into configuration
#endif
#if ( CONFIG_CLKIN_HALF == 0 )
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
#else
#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
#endif
#if (CONFIG_PLL_BYPASS == 0)
#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
#else
#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
#endif
#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
#else
#undef CONFIG_SPI_FLASH_FAST_READ
#endif
#endif
/*
* Command settings
*/
#define CFG_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
#endif
/* configuration lookup from the BOOTP/DHCP server, */
/* but not try to load any image using TFTP */
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CONFIG_BOOTCOMMAND "run ramboot"
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
#endif
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#if (CONFIG_DRIVER_SMC91111)
#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
"$(rootpath) console=ttyBF0,57600\0" \
"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
"ramboot=tftpboot $(loadaddr) linux; " \
"run ramargs;run addip;bootelf\0" \
"nfsboot=tftpboot $(loadaddr) linux; " \
"run nfsargs;run addip;bootelf\0" \
"flashboot=bootm 0x20100000\0" \
"update=tftpboot $(loadaddr) u-boot.bin; " \
"protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
""
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
"flashboot=bootm 0x20100000\0" \
"
#endif
#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
"$(rootpath) console=ttyBF0,57600\0" \
"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
"ramboot=tftpboot $(loadaddr) linux; " \
"run ramargs;run addip;bootelf\0" \
"nfsboot=tftpboot $(loadaddr) linux; " \
"run nfsargs;run addip;bootelf\0" \
"flashboot=bootm 0x20100000\0" \
"update=tftpboot $(loadaddr) u-boot.ldr;" \
"eeprom write $(loadaddr) 0x0 $(filesize);\0"\
""
#endif
#ifdef CONFIG_SOFT_I2C
#if (!CONFIG_SOFT_I2C)
#undef CONFIG_SOFT_I2C
#endif
#endif
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ELF
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_DATE
#if (CONFIG_DRIVER_SMC91111)
#define CONFIG_CMD_PING
#endif
#if (CONFIG_SOFT_I2C)
#define CONFIG_CMD_I2C
#endif
#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CONFIG_CMD_DHCP
#endif
/*
* Console settings
*/
#define CONFIG_BAUDRATE 57600
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CFG_PROMPT "bfin> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_LOADS_ECHO 1
/*
* I2C settings
* By default PF2 is used as SDA and PF3 as SCL on the Stamp board
*/
#if (CONFIG_SOFT_I2C)
#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
#define I2C_SDA(bit) if(bit) { \
*pFIO_FLAG_S = PF_SDA; \
asm("ssync;"); \
} \
else { \
*pFIO_FLAG_C = PF_SDA; \
asm("ssync;"); \
}
#define I2C_SCL(bit) if(bit) { \
*pFIO_FLAG_S = PF_SCL; \
asm("ssync;"); \
} \
else { \
*pFIO_FLAG_C = PF_SCL; \
asm("ssync;"); \
}
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CFG_I2C_SPEED 50000
#define CFG_I2C_SLAVE 0xFE
#endif /* CONFIG_SOFT_I2C */
/*
* Compact Flash settings
*/
/* Enabled below option for CF support */
/* #define CONFIG_STAMP_CF 1 */
#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE)
#define CONFIG_MISC_INIT_R 1
#define CONFIG_DOS_PARTITION 1
/*
* IDE/ATA stuff
*/
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
#define CFG_ATA_BASE_ADDR 0x20200000
#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
#define CFG_ATA_STRIDE 2
#endif
/*
* Miscellaneous configurable options
*/
#define CFG_HZ 1000 /* 1ms time tick */
#define CFG_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */
#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
#define CONFIG_SPI
#ifdef CONFIG_VIDEO
#if (CONFIG_VIDEO)
#define CONFIG_SPLASH_SCREEN 1
#define CONFIG_SILENT_CONSOLE 1
#else
#undef CONFIG_VIDEO
#endif
#endif
/*
* FLASH organization and environment definitions
*/
#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */
/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
*/
#define AMGCTLVAL 0xFF
#define AMBCTL0VAL 0xBBC3BBC3
#define AMBCTL1VAL 0x99B39983
#define CF_AMBCTL1VAL 0x99B3ffc2
#ifdef CONFIG_VDSP
#define ET_EXEC_VDSP 0x8
#define SHT_STRTAB_VDSP 0x1
#define ELFSHDRSIZE_VDSP 0x2C
#define VDSP_ENTRY_ADDR 0xFFA00000
#endif
#endif