mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 09:30:10 +00:00
32e7a6baef
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream. the twin-die combined memory device should be treatened as X8 device and not as X16 one Signed-off-by: Moti Buskila <motib@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com> [ - the default value for twin_die_combined is set to NOT_COMBINED for all boards, as this was default behaviour prior this change ] Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
262 lines
7.4 KiB
C
262 lines
7.4 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015 Stefan Roese <sr@denx.de>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <env.h>
|
|
#include <i2c.h>
|
|
#include <init.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/delay.h>
|
|
#include "../common/tlv_data.h"
|
|
|
|
#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
|
|
#include <../serdes/a38x/high_speed_env_spec.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* Those values and defines are taken from the Marvell U-Boot version
|
|
* "u-boot-2013.01-15t1-clearfog"
|
|
*/
|
|
#define BOARD_GPP_OUT_ENA_LOW 0xffffffff
|
|
#define BOARD_GPP_OUT_ENA_MID 0xffffffff
|
|
|
|
#define BOARD_GPP_OUT_VAL_LOW 0x0
|
|
#define BOARD_GPP_OUT_VAL_MID 0x0
|
|
#define BOARD_GPP_POL_LOW 0x0
|
|
#define BOARD_GPP_POL_MID 0x0
|
|
|
|
static struct tlv_data cf_tlv_data;
|
|
|
|
static void cf_read_tlv_data(void)
|
|
{
|
|
static bool read_once;
|
|
|
|
if (read_once)
|
|
return;
|
|
read_once = true;
|
|
|
|
read_tlv_data(&cf_tlv_data);
|
|
}
|
|
|
|
/* The starting board_serdes_map reflects original Clearfog Pro usage */
|
|
static struct serdes_map board_serdes_map[] = {
|
|
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
|
|
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
|
|
{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
|
|
};
|
|
|
|
void config_cfbase_serdes_map(void)
|
|
{
|
|
board_serdes_map[4].serdes_type = USB3_HOST0;
|
|
board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS;
|
|
board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
|
|
}
|
|
|
|
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
|
|
{
|
|
cf_read_tlv_data();
|
|
|
|
/* Apply build configuration options before runtime configuration */
|
|
if (IS_ENABLED(CONFIG_CLEARFOG_SFP_25GB))
|
|
board_serdes_map[5].serdes_speed = SERDES_SPEED_3_125_GBPS;
|
|
|
|
if (IS_ENABLED(CONFIG_CLEARFOG_CON2_SATA)) {
|
|
board_serdes_map[4].serdes_type = SATA2;
|
|
board_serdes_map[4].serdes_speed = SERDES_SPEED_3_GBPS;
|
|
board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE;
|
|
board_serdes_map[4].swap_rx = 1;
|
|
}
|
|
|
|
if (IS_ENABLED(CONFIG_CLEARFOG_CON3_SATA)) {
|
|
board_serdes_map[2].serdes_type = SATA1;
|
|
board_serdes_map[2].serdes_speed = SERDES_SPEED_3_GBPS;
|
|
board_serdes_map[2].serdes_mode = SERDES_DEFAULT_MODE;
|
|
board_serdes_map[2].swap_rx = 1;
|
|
}
|
|
|
|
/* Apply runtime detection changes */
|
|
if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) {
|
|
board_serdes_map[0].serdes_type = PEX0;
|
|
board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS;
|
|
board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
|
|
} else if (sr_product_is(&cf_tlv_data, "Clearfog Pro")) {
|
|
/* handle recognized product as noop, no adjustment required */
|
|
} else if (sr_product_is(&cf_tlv_data, "Clearfog Base")) {
|
|
config_cfbase_serdes_map();
|
|
} else {
|
|
/*
|
|
* Fallback to static default. EEPROM TLV support is not
|
|
* enabled, runtime detection failed, hardware support is not
|
|
* present, EEPROM is corrupt, or an unrecognized product name
|
|
* is present.
|
|
*/
|
|
if (IS_ENABLED(CONFIG_SPL_CMD_TLV_EEPROM))
|
|
puts("EEPROM TLV detection failed: ");
|
|
puts("Using static config for ");
|
|
if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE)) {
|
|
puts("Clearfog Base.\n");
|
|
config_cfbase_serdes_map();
|
|
} else {
|
|
puts("Clearfog Pro.\n");
|
|
}
|
|
}
|
|
|
|
*serdes_map_array = board_serdes_map;
|
|
*count = ARRAY_SIZE(board_serdes_map);
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Define the DDR layout / topology here in the board file. This will
|
|
* be used by the DDR3 init code in the SPL U-Boot version to configure
|
|
* the DDR3 controller.
|
|
*/
|
|
static struct mv_ddr_topology_map board_topology_map = {
|
|
DEBUG_LEVEL_ERROR,
|
|
0x1, /* active interfaces */
|
|
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
|
|
{ { { {0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0},
|
|
{0x1, 0, 0, 0} },
|
|
SPEED_BIN_DDR_1600K, /* speed_bin */
|
|
MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
|
|
MV_DDR_DIE_CAP_4GBIT, /* mem_size */
|
|
MV_DDR_FREQ_800, /* frequency */
|
|
0, 0, /* cas_wl cas_l */
|
|
MV_DDR_TEMP_LOW, /* temperature */
|
|
MV_DDR_TIM_DEFAULT} }, /* timing */
|
|
BUS_MASK_32BIT, /* Busses mask */
|
|
MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
|
|
NOT_COMBINED, /* ddr twin-die combined */
|
|
{ {0} }, /* raw spd data */
|
|
{0}, /* timing parameters */
|
|
{ {0} }, /* electrical configuration */
|
|
{0,}, /* electrical parameters */
|
|
0x3, /* clock enable mask */
|
|
};
|
|
|
|
struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
|
|
{
|
|
struct if_params *ifp = &board_topology_map.interface_params[0];
|
|
|
|
cf_read_tlv_data();
|
|
|
|
switch (cf_tlv_data.ram_size) {
|
|
case 4:
|
|
default:
|
|
ifp->memory_size = MV_DDR_DIE_CAP_4GBIT;
|
|
break;
|
|
case 8:
|
|
ifp->memory_size = MV_DDR_DIE_CAP_8GBIT;
|
|
break;
|
|
}
|
|
|
|
/* Return the board topology as defined in the board code */
|
|
return &board_topology_map;
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* Configure MPP */
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x00);
|
|
writel(0x11111111, MVEBU_MPP_BASE + 0x04);
|
|
writel(0x10400011, MVEBU_MPP_BASE + 0x08);
|
|
writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
|
|
writel(0x44400002, MVEBU_MPP_BASE + 0x10);
|
|
writel(0x41144004, MVEBU_MPP_BASE + 0x14);
|
|
writel(0x40333333, MVEBU_MPP_BASE + 0x18);
|
|
writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
|
|
|
|
/* Set GPP Out value */
|
|
writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
|
|
writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
|
|
|
|
/* Set GPP Polarity */
|
|
writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
|
|
writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
|
|
|
|
/* Set GPP Out Enable */
|
|
writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
|
|
writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
/* Toggle GPIO41 to reset onboard switch and phy */
|
|
clrbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
|
|
clrbits_le32(MVEBU_GPIO1_BASE + 0x4, BIT(9));
|
|
/* GPIO 19 on ClearFog rev 2.1 controls the uSOM onboard phy reset */
|
|
clrbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
|
|
clrbits_le32(MVEBU_GPIO0_BASE + 0x4, BIT(19));
|
|
mdelay(1);
|
|
setbits_le32(MVEBU_GPIO1_BASE + 0x0, BIT(9));
|
|
setbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
|
|
mdelay(10);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
char *board = "Clearfog Pro";
|
|
if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
|
|
board = "Clearfog Base";
|
|
|
|
cf_read_tlv_data();
|
|
if (strlen(cf_tlv_data.tlv_product_name[0]) > 0)
|
|
board = cf_tlv_data.tlv_product_name[0];
|
|
|
|
printf("Board: SolidRun %s", board);
|
|
if (strlen(cf_tlv_data.tlv_product_name[1]) > 0)
|
|
printf(", %s", cf_tlv_data.tlv_product_name[1]);
|
|
puts("\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(struct bd_info *bis)
|
|
{
|
|
cpu_eth_init(bis); /* Built in controller(s) come first */
|
|
return pci_eth_init(bis);
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
if (env_get("fdtfile"))
|
|
return 0;
|
|
|
|
cf_read_tlv_data();
|
|
|
|
if (sr_product_is(&cf_tlv_data, "Clearfog Base"))
|
|
env_set("fdtfile", "armada-388-clearfog-base.dtb");
|
|
else if (sr_product_is(&cf_tlv_data, "Clearfog GTR S4"))
|
|
env_set("fdtfile", "armada-385-clearfog-gtr-s4.dtb");
|
|
else if (sr_product_is(&cf_tlv_data, "Clearfog GTR L8"))
|
|
env_set("fdtfile", "armada-385-clearfog-gtr-l8.dtb");
|
|
else if (IS_ENABLED(CONFIG_TARGET_CLEARFOG_BASE))
|
|
env_set("fdtfile", "armada-388-clearfog-base.dtb");
|
|
else
|
|
env_set("fdtfile", "armada-388-clearfog-pro.dtb");
|
|
|
|
return 0;
|
|
}
|