mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
d126e01649
This patch moves the following config options to Kconfig: CONFIG_AUTOBOOT_KEYED CONFIG_AUTOBOOT_PROMPT CONFIG_AUTOBOOT_DELAY_STR CONFIG_AUTOBOOT_STOP_STR AUTOBOOT_KEYED_CTRLC Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> [trini: Drop ip04 and pm9263 configs/ additions, those boards previously set CONFIG_AUTOBOOT_PROMPT but never used it, re-run savedefconfig over all boards that did change. Make digsy_mtc_* string include seconds to match others and not warn. ] Signed-off-by: Tom Rini <trini@konsulko.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
392 lines
11 KiB
C
392 lines
11 KiB
C
/*
|
|
* (C) Copyright 2003-2007
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* Based on Motion-PRO board config file by Robert McCullough, rob@promessinc.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
|
|
/* CPU and board */
|
|
#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
|
|
#define CONFIG_MOTIONPRO 1 /* ... on Promess Motion-PRO board */
|
|
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xfff00000
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_BEDBUG
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_DTT
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_IDE
|
|
#define CONFIG_CMD_IMMAP
|
|
#define CONFIG_CMD_JFFS2
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_REGINFO
|
|
|
|
/*
|
|
* Serial console configuration
|
|
*/
|
|
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
|
|
#define CONFIG_NETCONSOLE 1 /* network console */
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
|
|
|
|
/*
|
|
* Ethernet configuration
|
|
*/
|
|
#define CONFIG_MPC5xxx_FEC 1
|
|
#define CONFIG_MPC5xxx_FEC_MII100
|
|
#define CONFIG_PHY_ADDR 0x2
|
|
#define CONFIG_PHY_TYPE 0x79c874
|
|
#define CONFIG_RESET_PHY_R 1
|
|
|
|
/*
|
|
* Autobooting
|
|
*/
|
|
#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
|
|
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
|
|
|
|
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
|
|
|
|
/*
|
|
* Default environment settings
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"hostname=motionpro\0" \
|
|
"netmask=255.255.255.0\0" \
|
|
"ipaddr=192.168.1.106\0" \
|
|
"serverip=192.168.1.100\0" \
|
|
"gatewayip=192.168.1.100\0" \
|
|
"console=ttyPSC0,115200\0" \
|
|
"u-boot_addr=400000\0" \
|
|
"kernel_addr=400000\0" \
|
|
"fdt_addr=700000\0" \
|
|
"ramdisk_addr=800000\0" \
|
|
"multi_image_addr=800000\0" \
|
|
"rootpath=/opt/eldk-4.2/ppc_6xx\0" \
|
|
"u-boot=/tftpboot/motionpro/u-boot.bin\0" \
|
|
"bootfile=/tftpboot/motionpro/uImage\0" \
|
|
"fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \
|
|
"ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \
|
|
"multi_image_file=kernel+initrd+dtb.img\0" \
|
|
"load=tftp ${u-boot_addr} ${u-boot}\0" \
|
|
"update=prot off fff00000 +${filesize};" \
|
|
"era fff00000 +${filesize}; " \
|
|
"cp.b ${u-boot_addr} fff00000 ${filesize};" \
|
|
"prot on fff00000 +${filesize}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"fat_args=setenv bootargs root=/dev/sda rw\0" \
|
|
"mtdids=nor0=ff000000.flash\0" \
|
|
"mtdparts=ff000000.flash:13m(fs),2m(kernel),384k(uboot)," \
|
|
"128k(env),128k(redund_env)," \
|
|
"128k(dtb),128k(user_data)\0" \
|
|
"addcons=setenv bootargs ${bootargs} console=${console}\0" \
|
|
"addmtd=setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:" \
|
|
"${netmask}:${hostname}:${netdev}:off panic=1 " \
|
|
"console=${console}\0" \
|
|
"net_nfs=tftp ${kernel_addr} ${bootfile}; " \
|
|
"tftp ${fdt_addr} ${fdt_file}; " \
|
|
"run nfsargs addip addmtd; " \
|
|
"bootm ${kernel_addr} - ${fdt_addr}\0" \
|
|
"net_self=tftp ${kernel_addr} ${bootfile}; " \
|
|
"tftp ${fdt_addr} ${fdt_file}; " \
|
|
"tftp ${ramdisk_addr} ${ramdisk_file}; " \
|
|
"nfs ${ramdisk_addr} ${serverip}:${rootpath}/images/uRamdisk; " \
|
|
"run ramargs addip addcons addmtd; " \
|
|
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
|
"fat_multi=run fat_args addip addmtd; fatload ide 0:1 " \
|
|
"${multi_image_addr} ${multi_image_file}; " \
|
|
"bootm ${multi_image_addr}\0" \
|
|
""
|
|
#define CONFIG_BOOTCOMMAND "run fat_multi"
|
|
|
|
/*
|
|
* do board-specific init
|
|
*/
|
|
#define CONFIG_BOARD_EARLY_INIT_R 1
|
|
|
|
/*
|
|
* Low level configuration
|
|
*/
|
|
|
|
/*
|
|
* Clock configuration: SYS_XTALIN = 33MHz
|
|
*/
|
|
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
|
|
|
|
/*
|
|
* Set IPB speed to 100MHz
|
|
*/
|
|
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK
|
|
|
|
/*
|
|
* Memory map
|
|
*/
|
|
/*
|
|
* Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000.
|
|
* Setting MBAR to otherwise will cause system hang when using SmartDMA such
|
|
* as network commands.
|
|
*/
|
|
#define CONFIG_SYS_MBAR 0xf0000000
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
|
|
/*
|
|
* If building for running out of SDRAM, then MBAR has been set up beforehand
|
|
* (e.g., by the BDI). Otherwise we must specify the default boot-up value of
|
|
* MBAR, as given in the doccumentation.
|
|
*/
|
|
#if CONFIG_SYS_TEXT_BASE == 0x00100000
|
|
#define CONFIG_SYS_DEFAULT_MBAR 0xf0000000
|
|
#else /* CONFIG_SYS_TEXT_BASE != 0x00100000 */
|
|
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
|
|
#define CONFIG_SYS_LOWBOOT 1
|
|
#endif /* CONFIG_SYS_TEXT_BASE == 0x00100000 */
|
|
|
|
/* Use SRAM until RAM will be available */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
|
|
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_SYS_RAMBOOT 1
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* 384 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* 1 MiB for malloc() */
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */
|
|
|
|
/*
|
|
* Chip selects configuration
|
|
*/
|
|
/* Boot Chipselect */
|
|
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
|
|
#define CONFIG_SYS_BOOTCS_CFG 0x00045D00
|
|
|
|
/* Flash memory addressing */
|
|
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
|
|
#define CONFIG_SYS_CS0_CFG CONFIG_SYS_BOOTCS_CFG
|
|
|
|
/* Dual Port SRAM -- Kollmorgen Drive memory addressing */
|
|
#define CONFIG_SYS_CS1_START 0x50000000
|
|
#define CONFIG_SYS_CS1_SIZE 0x10000
|
|
#define CONFIG_SYS_CS1_CFG 0x05055800
|
|
|
|
/* Local register access */
|
|
#define CONFIG_SYS_CS2_START 0x50010000
|
|
#define CONFIG_SYS_CS2_SIZE 0x10000
|
|
#define CONFIG_SYS_CS2_CFG 0x05055800
|
|
|
|
/* Anybus CompactCom Module memory addressing */
|
|
#define CONFIG_SYS_CS3_START 0x50020000
|
|
#define CONFIG_SYS_CS3_SIZE 0x10000
|
|
#define CONFIG_SYS_CS3_CFG 0x05055800
|
|
|
|
/* No burst and dead cycle = 2 for all CSs */
|
|
#define CONFIG_SYS_CS_BURST 0x00000000
|
|
#define CONFIG_SYS_CS_DEADCYCLE 0x22222222
|
|
|
|
/*
|
|
* SDRAM configuration
|
|
*/
|
|
/* 2 x MT48LC16M16A2BG-75 IT:D, CASL 3, 32 bit data bus */
|
|
#define SDRAM_CONFIG1 0x62322900
|
|
#define SDRAM_CONFIG2 0x88c70000
|
|
#define SDRAM_CONTROL 0x504f0000
|
|
#define SDRAM_MODE 0x00cd0000
|
|
|
|
/*
|
|
* Flash configuration
|
|
*/
|
|
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
|
|
#define CONFIG_FLASH_CFI_DRIVER 1
|
|
#define CONFIG_SYS_FLASH_BASE 0xff000000
|
|
#define CONFIG_SYS_FLASH_SIZE 0x01000000
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
|
|
#define CONFIG_FLASH_16BIT /* Flash is 16-bit */
|
|
|
|
/*
|
|
* MTD configuration
|
|
*/
|
|
#define CONFIG_CMD_MTDPARTS
|
|
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
|
|
#define CONFIG_FLASH_CFI_MTD
|
|
#define MTDIDS_DEFAULT "nor0=motionpro-0"
|
|
#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \
|
|
"13m(fs),2m(kernel),384k(uboot)," \
|
|
"128k(env),128k(redund_env)," \
|
|
"128k(dtb),-(user_data)"
|
|
|
|
/*
|
|
* IDE/ATA configuration
|
|
*/
|
|
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
|
|
#define CONFIG_SYS_IDE_MAXBUS 1
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 1
|
|
#define CONFIG_IDE_PREINIT
|
|
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060
|
|
#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
|
|
#define CONFIG_SYS_ATA_STRIDE 4
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
/*
|
|
* I2C configuration
|
|
*/
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
|
|
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
/*
|
|
* EEPROM configuration
|
|
*/
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
|
|
#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */
|
|
|
|
/*
|
|
* RTC configuration
|
|
*/
|
|
#define CONFIG_RTC_DS1337 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
|
|
/*
|
|
* Status LED configuration
|
|
*/
|
|
#define CONFIG_STATUS_LED /* Status LED enabled */
|
|
#define CONFIG_BOARD_SPECIFIC_LED
|
|
|
|
#define ENABLE_GPIO_OUT 0x00000024
|
|
#define LED_ON 0x00000010
|
|
|
|
#ifndef __ASSEMBLY__
|
|
/*
|
|
* In case of Motion-PRO, a LED is identified by its corresponding
|
|
* GPT Enable and Mode Select Register.
|
|
*/
|
|
typedef volatile unsigned long * led_id_t;
|
|
|
|
extern void __led_init(led_id_t id, int state);
|
|
extern void __led_toggle(led_id_t id);
|
|
extern void __led_set(led_id_t id, int state);
|
|
#endif /* __ASSEMBLY__ */
|
|
|
|
/*
|
|
* Temperature sensor
|
|
*/
|
|
#define CONFIG_DTT_LM75 1
|
|
#define CONFIG_DTT_SENSORS { 0x49 }
|
|
|
|
/*
|
|
* Environment settings
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
/* This has to be a multiple of the Flash sector size */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_ENV_SIZE 0x1000
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
|
|
/* Configuration of redundant environment */
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
|
|
/*
|
|
* Pin multiplexing configuration
|
|
*/
|
|
|
|
/* PSC1: UART1
|
|
* PSC2: GPIO (default)
|
|
* PSC3: GPIO (default)
|
|
* USB: 2xUART4/5
|
|
* Ethernet: Ethernet 100Mbit with MD
|
|
* Timer: CAN2/GPIO
|
|
* PSC6/IRDA: GPIO (default)
|
|
*/
|
|
#define CONFIG_SYS_GPS_PORT_CONFIG 0x1105a004
|
|
|
|
/*
|
|
* Motion-PRO's CPLD revision control register
|
|
*/
|
|
#define CPLD_REV_REGISTER (CONFIG_SYS_CS2_START + 0x06)
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x03e00000 /* 1 ... 62 MiB in DRAM */
|
|
#define CONFIG_SYS_ALT_MEMTEST
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default kernel load addr */
|
|
|
|
/*
|
|
* Various low-level settings
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
|
|
#define CONFIG_SYS_HID0_FINAL HID0_ICE
|
|
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
|
|
|
|
/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
|
|
|
|
/* pass open firmware flat tree */
|
|
#define CONFIG_OF_LIBFDT 1
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
|
|
#define OF_CPU "PowerPC,5200@0"
|
|
#define OF_SOC "soc5200@f0000000"
|
|
#define OF_TBCLK (bd->bi_busfreq / 4)
|
|
#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
|
|
|
|
#endif /* __CONFIG_H */
|