u-boot/board/mpc832xemds/mpc832xemds.c
Dave Liu 24c3aca3f1 mpc83xx: Add support for the MPC832XEMDS board
This patch supports DUART, ETH3/4 and PCI etc.

Signed-off-by: Dave Liu <daveliu@freescale.com>
2007-03-02 11:05:53 -06:00

176 lines
4.2 KiB
C

/*
* Copyright (C) 2006 Freescale Semiconductor, Inc.
*
* Dave Liu <daveliu@freescale.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*/
#include <common.h>
#include <ioports.h>
#include <mpc83xx.h>
#include <i2c.h>
#include <spd.h>
#include <miiphy.h>
#include <command.h>
#if defined(CONFIG_PCI)
#include <pci.h>
#endif
#if defined(CONFIG_SPD_EEPROM)
#include <spd_sdram.h>
#else
#include <asm/mmu.h>
#endif
#if defined(CONFIG_OF_FLAT_TREE)
#include <ft_build.h>
#endif
const qe_iop_conf_t qe_iop_conf_tab[] = {
/* ETH3 */
{1, 0, 1, 0, 1}, /* TxD0 */
{1, 1, 1, 0, 1}, /* TxD1 */
{1, 2, 1, 0, 1}, /* TxD2 */
{1, 3, 1, 0, 1}, /* TxD3 */
{1, 9, 1, 0, 1}, /* TxER */
{1, 12, 1, 0, 1}, /* TxEN */
{3, 24, 2, 0, 1}, /* TxCLK->CLK10 */
{1, 4, 2, 0, 1}, /* RxD0 */
{1, 5, 2, 0, 1}, /* RxD1 */
{1, 6, 2, 0, 1}, /* RxD2 */
{1, 7, 2, 0, 1}, /* RxD3 */
{1, 8, 2, 0, 1}, /* RxER */
{1, 10, 2, 0, 1}, /* RxDV */
{0, 13, 2, 0, 1}, /* RxCLK->CLK9 */
{1, 11, 2, 0, 1}, /* COL */
{1, 13, 2, 0, 1}, /* CRS */
/* ETH4 */
{1, 18, 1, 0, 1}, /* TxD0 */
{1, 19, 1, 0, 1}, /* TxD1 */
{1, 20, 1, 0, 1}, /* TxD2 */
{1, 21, 1, 0, 1}, /* TxD3 */
{1, 27, 1, 0, 1}, /* TxER */
{1, 30, 1, 0, 1}, /* TxEN */
{3, 6, 2, 0, 1}, /* TxCLK->CLK8 */
{1, 22, 2, 0, 1}, /* RxD0 */
{1, 23, 2, 0, 1}, /* RxD1 */
{1, 24, 2, 0, 1}, /* RxD2 */
{1, 25, 2, 0, 1}, /* RxD3 */
{1, 26, 1, 0, 1}, /* RxER */
{1, 28, 2, 0, 1}, /* Rx_DV */
{3, 31, 2, 0, 1}, /* RxCLK->CLK7 */
{1, 29, 2, 0, 1}, /* COL */
{1, 31, 2, 0, 1}, /* CRS */
{3, 4, 3, 0, 2}, /* MDIO */
{3, 5, 1, 0, 2}, /* MDC */
{0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */
};
int board_early_init_f(void)
{
volatile u8 *bcsr = (volatile u8 *)CFG_BCSR;
/* Enable flash write */
bcsr[9] &= ~0x08;
return 0;
}
int fixed_sdram(void);
long int initdram(int board_type)
{
volatile immap_t *im = (immap_t *) CFG_IMMR;
u32 msize = 0;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
return -1;
/* DDR SDRAM - Main SODIMM */
im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR;
msize = fixed_sdram();
puts("\n DDR RAM: ");
/* return total bus SDRAM size(bytes) -- DDR */
return (msize * 1024 * 1024);
}
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
************************************************************************/
int fixed_sdram(void)
{
volatile immap_t *im = (immap_t *) CFG_IMMR;
u32 msize = 0;
u32 ddr_size;
u32 ddr_size_log2;
msize = CFG_DDR_SIZE;
for (ddr_size = msize << 20, ddr_size_log2 = 0;
(ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) {
if (ddr_size & 1) {
return -1;
}
}
im->sysconf.ddrlaw[0].ar =
LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
#if (CFG_DDR_SIZE != 128)
#warning Currenly any ddr size other than 128 is not supported
#endif
im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL;
im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS;
im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG;
im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG;
im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2;
im->ddr.sdram_mode = CFG_DDR_MODE;
im->ddr.sdram_mode2 = CFG_DDR_MODE2;
im->ddr.sdram_interval = CFG_DDR_INTERVAL;
__asm__ __volatile__ ("sync");
udelay(200);
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
__asm__ __volatile__ ("sync");
return msize;
}
int checkboard(void)
{
puts("Board: Freescale MPC832XEMDS\n");
return 0;
}
#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
void
ft_board_setup(void *blob, bd_t *bd)
{
u32 *p;
int len;
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
#endif
ft_cpu_setup(blob, bd);
p = ft_get_prop(blob, "/memory/reg", &len);
if (p != NULL) {
*p++ = cpu_to_be32(bd->bi_memstart);
*p = cpu_to_be32(bd->bi_memsize);
}
}
#endif