mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-03 09:59:44 +00:00
09f3ca3dd5
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
188 lines
7 KiB
C
188 lines
7 KiB
C
/*
|
|
* bur_am335x_common.h
|
|
*
|
|
* common parts used by B&R AM335x based boards
|
|
*
|
|
* Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at> -
|
|
* Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __BUR_AM335X_COMMON_H__
|
|
#define __BUR_AM335X_COMMON_H__
|
|
/* ------------------------------------------------------------------------- */
|
|
#define BUR_COMMON_ENV \
|
|
"usbscript=usb start && fatload usb 0 0x80000000 usbscript.img && source\0" \
|
|
"brdefaultip=if test -r ${ipaddr}; then; else" \
|
|
" setenv ipaddr 192.168.60.1; setenv serverip 192.168.60.254;" \
|
|
" setenv gatewayip 192.168.60.254; setenv netmask 255.255.255.0; fi;\0" \
|
|
"netconsole=echo switching to network console ...; " \
|
|
"if dhcp; then; else run brdefaultip; fi; setenv ncip ${serverip}; " \
|
|
"setcurs 1 9; lcdputs myip; setcurs 10 9; lcdputs ${ipaddr};" \
|
|
"setcurs 1 10;lcdputs serverip; setcurs 10 10; lcdputs ${serverip};" \
|
|
"setenv stdout nc;setenv stdin nc;setenv stderr nc\0"
|
|
|
|
#define CONFIG_PREBOOT "run brdefaultip"
|
|
#define CONFIG_CMD_TIME
|
|
|
|
|
|
#define CONFIG_AM33XX
|
|
#define CONFIG_OMAP
|
|
#define CONFIG_OMAP_COMMON
|
|
#define CONFIG_BOARD_LATE_INIT
|
|
#define CONFIG_SYS_CACHELINE_SIZE 64
|
|
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
|
|
|
|
/* Timer information */
|
|
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
|
|
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
|
|
#define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC /* enable 32kHz OSC at bootime */
|
|
#define CONFIG_SPL_POWER_SUPPORT
|
|
#define CONFIG_POWER_TPS65217
|
|
|
|
#define CONFIG_SYS_NO_FLASH /* have no NOR-flash */
|
|
|
|
#include <asm/arch/omap.h>
|
|
|
|
/* NS16550 Configuration */
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
|
|
#define CONFIG_SYS_NS16550_CLK 48000000
|
|
#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
/* Network defines */
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */
|
|
#define CONFIG_BOOTP_SEND_HOSTNAME
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_NET_RETRY_COUNT 2
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */
|
|
#define CONFIG_MII /* Required in net/eth.c */
|
|
#define CONFIG_SPL_ETH_SUPPORT
|
|
#define CONFIG_PHYLIB
|
|
#define CONFIG_PHY_NATSEMI
|
|
#define CONFIG_SPL_NET_SUPPORT
|
|
#define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */
|
|
#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL"
|
|
/* Network console */
|
|
#define CONFIG_NETCONSOLE 1
|
|
#define CONFIG_BOOTP_MAY_FAIL /* if we don't have DHCP environment */
|
|
/*
|
|
* SPL related defines. The Public RAM memory map the ROM defines the
|
|
* area between 0x402F0400 and 0x4030B800 as a download area and
|
|
* 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also
|
|
* supports X-MODEM loading via UART, and we leverage this and then use
|
|
* Y-MODEM to load u-boot.img, when booted over UART.
|
|
*/
|
|
#define CONFIG_SPL_TEXT_BASE 0x402F0400
|
|
#define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE)
|
|
|
|
/*
|
|
* Since SPL did pll and ddr initialization for us,
|
|
* we don't need to do it twice.
|
|
*/
|
|
#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT)
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT
|
|
#endif /* !CONFIG_SPL_BUILD, ... */
|
|
/*
|
|
* Our DDR memory always starts at 0x80000000 and U-Boot shall have
|
|
* relocated itself to higher in memory by the time this value is used.
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x80000000
|
|
/*
|
|
* ----------------------------------------------------------------------------
|
|
* DDR information. We say (for simplicity) that we have 1 bank,
|
|
* always, even when we have more. We always start at 0x80000000,
|
|
* and we place the initial stack pointer in our SRAM.
|
|
*/
|
|
#define CONFIG_NR_DRAM_BANKS 1
|
|
#define CONFIG_SYS_SDRAM_BASE 0x80000000
|
|
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
|
|
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
|
|
#define CONFIG_SYS_I2C_OMAP24XX
|
|
#define CONFIG_CMD_I2C
|
|
/* GPIO */
|
|
#define CONFIG_OMAP_GPIO
|
|
#define CONFIG_CMD_GPIO
|
|
/*
|
|
* ----------------------------------------------------------------------------
|
|
* The following are general good-enough settings for U-Boot. We set a
|
|
* large malloc pool as we generally have a lot of DDR, and we opt for
|
|
* function over binary size in the main portion of U-Boot as this is
|
|
* generally easily constrained later if needed. We enable the config
|
|
* options that give us information in the environment about what board
|
|
* we are on so we do not need to rely on the command prompt. We set a
|
|
* console baudrate of 115200 and use the default baud rate table.
|
|
*/
|
|
#define CONFIG_SYS_MALLOC_LEN (5120 << 10)
|
|
#define CONFIG_SYS_HUSH_PARSER
|
|
#define CONFIG_SYS_CONSOLE_INFO_QUIET
|
|
#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
|
|
|
|
/* As stated above, the following choices are optional. */
|
|
#define CONFIG_SYS_LONGHELP
|
|
#define CONFIG_AUTO_COMPLETE
|
|
#define CONFIG_CMDLINE_EDITING
|
|
#define CONFIG_VERSION_VARIABLE
|
|
|
|
/* We set the max number of command args high to avoid HUSH bugs. */
|
|
#define CONFIG_SYS_MAXARGS 64
|
|
|
|
/* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_CBSIZE 512
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\
|
|
sizeof(CONFIG_SYS_PROMPT) + 16)
|
|
/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
/*
|
|
* Our platforms make use of SPL to initalize the hardware (primarily
|
|
* memory) enough for full U-Boot to be loaded. We also support Falcon
|
|
* Mode so that the Linux kernel can be booted directly from SPL
|
|
* instead, if desired. We make use of the general SPL framework found
|
|
* under common/spl/. Given our generally common memory map, we set a
|
|
* number of related defaults and sizes here.
|
|
*/
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
/*
|
|
* Place the image at the start of the ROM defined image space.
|
|
* We limit our size to the ROM-defined downloaded image area, and use the
|
|
* rest of the space for stack. We load U-Boot itself into memory at
|
|
* 0x80800000 for legacy reasons (to not conflict with older SPLs). We
|
|
* have our BSS be placed 1MiB after this, to allow for the default
|
|
* Linux kernel address of 0x80008000 to work, in the Falcon Mode case.
|
|
* We have the SPL malloc pool at the end of the BSS area.
|
|
*
|
|
* ----------------------------------------------------------------------------
|
|
*/
|
|
#undef CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_TEXT_BASE 0x80800000
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x80A00000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
|
|
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
|
|
CONFIG_SPL_BSS_MAX_SIZE)
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
|
|
|
|
/* General parts of the framework, required. */
|
|
#define CONFIG_SPL_I2C_SUPPORT
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
|
#define CONFIG_SPL_SERIAL_SUPPORT
|
|
#define CONFIG_SPL_BOARD_INIT
|
|
#define CONFIG_SPL_YMODEM_SUPPORT
|
|
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
|
|
|
|
#endif /* ! __BUR_AM335X_COMMON_H__ */
|