mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 04:23:46 +00:00
a430fa06a4
NAND flavors, like serial and parallel, have a lot in common and would benefit to share code. Let's move raw (parallel) NAND specific code in a raw/ subdirectory, to ease the addition of a core file in nand/ and the introduction of a spi/ subdirectory specific to SPI NANDs. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
240 lines
6.2 KiB
C
240 lines
6.2 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2006-2008
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <nand.h>
|
|
#include <asm/io.h>
|
|
#include <linux/mtd/nand_ecc.h>
|
|
|
|
static int nand_ecc_pos[] = CONFIG_SYS_NAND_ECCPOS;
|
|
static struct mtd_info *mtd;
|
|
static struct nand_chip nand_chip;
|
|
|
|
#define ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
|
|
CONFIG_SYS_NAND_ECCSIZE)
|
|
#define ECCTOTAL (ECCSTEPS * CONFIG_SYS_NAND_ECCBYTES)
|
|
|
|
|
|
#if (CONFIG_SYS_NAND_PAGE_SIZE <= 512)
|
|
/*
|
|
* NAND command for small page NAND devices (512)
|
|
*/
|
|
static int nand_command(int block, int page, uint32_t offs,
|
|
u8 cmd)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
int page_addr = page + block * CONFIG_SYS_NAND_PAGE_COUNT;
|
|
|
|
while (!this->dev_ready(mtd))
|
|
;
|
|
|
|
/* Begin command latch cycle */
|
|
this->cmd_ctrl(mtd, cmd, NAND_CTRL_CLE | NAND_CTRL_CHANGE);
|
|
/* Set ALE and clear CLE to start address cycle */
|
|
/* Column address */
|
|
this->cmd_ctrl(mtd, offs, NAND_CTRL_ALE | NAND_CTRL_CHANGE);
|
|
this->cmd_ctrl(mtd, page_addr & 0xff, NAND_CTRL_ALE); /* A[16:9] */
|
|
this->cmd_ctrl(mtd, (page_addr >> 8) & 0xff,
|
|
NAND_CTRL_ALE); /* A[24:17] */
|
|
#ifdef CONFIG_SYS_NAND_4_ADDR_CYCLE
|
|
/* One more address cycle for devices > 32MiB */
|
|
this->cmd_ctrl(mtd, (page_addr >> 16) & 0x0f,
|
|
NAND_CTRL_ALE); /* A[28:25] */
|
|
#endif
|
|
/* Latch in address */
|
|
this->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
|
|
|
|
/*
|
|
* Wait a while for the data to be ready
|
|
*/
|
|
while (!this->dev_ready(mtd))
|
|
;
|
|
|
|
return 0;
|
|
}
|
|
#else
|
|
/*
|
|
* NAND command for large page NAND devices (2k)
|
|
*/
|
|
static int nand_command(int block, int page, uint32_t offs,
|
|
u8 cmd)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
int page_addr = page + block * CONFIG_SYS_NAND_PAGE_COUNT;
|
|
void (*hwctrl)(struct mtd_info *mtd, int cmd,
|
|
unsigned int ctrl) = this->cmd_ctrl;
|
|
|
|
while (!this->dev_ready(mtd))
|
|
;
|
|
|
|
/* Emulate NAND_CMD_READOOB */
|
|
if (cmd == NAND_CMD_READOOB) {
|
|
offs += CONFIG_SYS_NAND_PAGE_SIZE;
|
|
cmd = NAND_CMD_READ0;
|
|
}
|
|
|
|
/* Shift the offset from byte addressing to word addressing. */
|
|
if ((this->options & NAND_BUSWIDTH_16) && !nand_opcode_8bits(cmd))
|
|
offs >>= 1;
|
|
|
|
/* Begin command latch cycle */
|
|
hwctrl(mtd, cmd, NAND_CTRL_CLE | NAND_CTRL_CHANGE);
|
|
/* Set ALE and clear CLE to start address cycle */
|
|
/* Column address */
|
|
hwctrl(mtd, offs & 0xff,
|
|
NAND_CTRL_ALE | NAND_CTRL_CHANGE); /* A[7:0] */
|
|
hwctrl(mtd, (offs >> 8) & 0xff, NAND_CTRL_ALE); /* A[11:9] */
|
|
/* Row address */
|
|
hwctrl(mtd, (page_addr & 0xff), NAND_CTRL_ALE); /* A[19:12] */
|
|
hwctrl(mtd, ((page_addr >> 8) & 0xff),
|
|
NAND_CTRL_ALE); /* A[27:20] */
|
|
#ifdef CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
/* One more address cycle for devices > 128MiB */
|
|
hwctrl(mtd, (page_addr >> 16) & 0x0f,
|
|
NAND_CTRL_ALE); /* A[31:28] */
|
|
#endif
|
|
/* Latch in address */
|
|
hwctrl(mtd, NAND_CMD_READSTART,
|
|
NAND_CTRL_CLE | NAND_CTRL_CHANGE);
|
|
hwctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
|
|
|
|
/*
|
|
* Wait a while for the data to be ready
|
|
*/
|
|
while (!this->dev_ready(mtd))
|
|
;
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static int nand_is_bad_block(int block)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
u_char bb_data[2];
|
|
|
|
nand_command(block, 0, CONFIG_SYS_NAND_BAD_BLOCK_POS,
|
|
NAND_CMD_READOOB);
|
|
|
|
/*
|
|
* Read one byte (or two if it's a 16 bit chip).
|
|
*/
|
|
if (this->options & NAND_BUSWIDTH_16) {
|
|
this->read_buf(mtd, bb_data, 2);
|
|
if (bb_data[0] != 0xff || bb_data[1] != 0xff)
|
|
return 1;
|
|
} else {
|
|
this->read_buf(mtd, bb_data, 1);
|
|
if (bb_data[0] != 0xff)
|
|
return 1;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if defined(CONFIG_SYS_NAND_HW_ECC_OOBFIRST)
|
|
static int nand_read_page(int block, int page, uchar *dst)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
u_char ecc_calc[ECCTOTAL];
|
|
u_char ecc_code[ECCTOTAL];
|
|
u_char oob_data[CONFIG_SYS_NAND_OOBSIZE];
|
|
int i;
|
|
int eccsize = CONFIG_SYS_NAND_ECCSIZE;
|
|
int eccbytes = CONFIG_SYS_NAND_ECCBYTES;
|
|
int eccsteps = ECCSTEPS;
|
|
uint8_t *p = dst;
|
|
|
|
nand_command(block, page, 0, NAND_CMD_READOOB);
|
|
this->read_buf(mtd, oob_data, CONFIG_SYS_NAND_OOBSIZE);
|
|
nand_command(block, page, 0, NAND_CMD_READ0);
|
|
|
|
/* Pick the ECC bytes out of the oob data */
|
|
for (i = 0; i < ECCTOTAL; i++)
|
|
ecc_code[i] = oob_data[nand_ecc_pos[i]];
|
|
|
|
|
|
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
|
|
this->ecc.hwctl(mtd, NAND_ECC_READ);
|
|
this->read_buf(mtd, p, eccsize);
|
|
this->ecc.calculate(mtd, p, &ecc_calc[i]);
|
|
this->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#else
|
|
static int nand_read_page(int block, int page, void *dst)
|
|
{
|
|
struct nand_chip *this = mtd_to_nand(mtd);
|
|
u_char ecc_calc[ECCTOTAL];
|
|
u_char ecc_code[ECCTOTAL];
|
|
u_char oob_data[CONFIG_SYS_NAND_OOBSIZE];
|
|
int i;
|
|
int eccsize = CONFIG_SYS_NAND_ECCSIZE;
|
|
int eccbytes = CONFIG_SYS_NAND_ECCBYTES;
|
|
int eccsteps = ECCSTEPS;
|
|
uint8_t *p = dst;
|
|
|
|
nand_command(block, page, 0, NAND_CMD_READ0);
|
|
|
|
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
|
|
if (this->ecc.mode != NAND_ECC_SOFT)
|
|
this->ecc.hwctl(mtd, NAND_ECC_READ);
|
|
this->read_buf(mtd, p, eccsize);
|
|
this->ecc.calculate(mtd, p, &ecc_calc[i]);
|
|
}
|
|
this->read_buf(mtd, oob_data, CONFIG_SYS_NAND_OOBSIZE);
|
|
|
|
/* Pick the ECC bytes out of the oob data */
|
|
for (i = 0; i < ECCTOTAL; i++)
|
|
ecc_code[i] = oob_data[nand_ecc_pos[i]];
|
|
|
|
eccsteps = ECCSTEPS;
|
|
p = dst;
|
|
|
|
for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
|
|
/* No chance to do something with the possible error message
|
|
* from correct_data(). We just hope that all possible errors
|
|
* are corrected by this routine.
|
|
*/
|
|
this->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
/* nand_init() - initialize data to make nand usable by SPL */
|
|
void nand_init(void)
|
|
{
|
|
/*
|
|
* Init board specific nand support
|
|
*/
|
|
mtd = nand_to_mtd(&nand_chip);
|
|
nand_chip.IO_ADDR_R = nand_chip.IO_ADDR_W =
|
|
(void __iomem *)CONFIG_SYS_NAND_BASE;
|
|
board_nand_init(&nand_chip);
|
|
|
|
#ifdef CONFIG_SPL_NAND_SOFTECC
|
|
if (nand_chip.ecc.mode == NAND_ECC_SOFT) {
|
|
nand_chip.ecc.calculate = nand_calculate_ecc;
|
|
nand_chip.ecc.correct = nand_correct_data;
|
|
}
|
|
#endif
|
|
|
|
if (nand_chip.select_chip)
|
|
nand_chip.select_chip(mtd, 0);
|
|
}
|
|
|
|
/* Unselect after operation */
|
|
void nand_deselect(void)
|
|
{
|
|
if (nand_chip.select_chip)
|
|
nand_chip.select_chip(mtd, -1);
|
|
}
|
|
|
|
#include "nand_spl_loaders.c"
|