mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 04:23:46 +00:00
1f55a93802
Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
216 lines
6.9 KiB
Text
216 lines
6.9 KiB
Text
Overview
|
|
--------
|
|
The LS2080A Development System (QDS) is a high-performance computing,
|
|
evaluation, and development platform that supports the QorIQ LS2080A
|
|
and LS2088A Layerscape Architecture processor. The LS2080AQDS provides
|
|
validation and SW development platform for the Freescale LS2080A, LS2088A
|
|
processor series, with a complete debugging environment.
|
|
|
|
LS2080A, LS2088A SoC Overview
|
|
--------------------
|
|
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A,
|
|
LS2088A SoC overview.
|
|
|
|
LS2080AQDS board Overview
|
|
-----------------------
|
|
- SERDES Connections, 16 lanes supporting:
|
|
- PCI Express - 3.0
|
|
- SGMII, SGMII 2.5
|
|
- QSGMII
|
|
- SATA 3.0
|
|
- XAUI
|
|
- XFI
|
|
- DDR Controller
|
|
- Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four
|
|
chip-selects and two DIMM connectors. Support is up to 2133MT/s.
|
|
- One port of 40-bits (8-bits ECC) DDR4 which supports four chip-selects
|
|
and two DIMM connectors. Support is up to 1600MT/s.
|
|
-IFC/Local Bus
|
|
- IFC rev. 2.0 implementation supporting Little Endian connection scheme.
|
|
- One in-socket 128 MB NOR flash 16-bit data bus
|
|
- One 512 MB NAND flash with ECC support
|
|
- IFC Test Port
|
|
- PromJet Port
|
|
- FPGA connection
|
|
- USB 3.0
|
|
- Two high speed USB 3.0 ports
|
|
- First USB 3.0 port configured as Host with Type-A connector
|
|
- Second USB 3.0 port configured as OTG with micro-AB connector
|
|
- SDHC: PCIe x1 Right Angle connector for supporting following cards
|
|
- 1/4-/8-bit SD/MMC Legacy CARD supporting 3.3V devices only
|
|
- 1-/4-/8-bit SD/MMC Card supporting 1.8V devices only
|
|
- 4-bit eMMC Card Rev 4.4 (1.8V only)
|
|
- 8-bit eMMC Card Rev 4.5 (1.8V only)
|
|
- SD Card Rev 2.0 and Rev 3.0
|
|
- DSPI: 3 high-speed flash Memory for storage
|
|
- 16 MB high-speed flash Memory for boot code and storage (up to 108MHz)
|
|
- 8 MB high-speed flash Memory (up to 104 MHz)
|
|
- 512 MB low-speed flash Memory (up to 40 MHz)
|
|
- QSPI: via NAND/QSPI Card
|
|
- 4 I2C controllers
|
|
- Two SATA onboard connectors
|
|
- UART
|
|
- Two 4-pin (HW control) or four 2-pin (SW control) serial ports at up to 115.2 Kbit/s
|
|
- Two DB9 D-Type connectors supporting one Serial port each
|
|
- ARM JTAG support
|
|
|
|
Memory map from core's view
|
|
----------------------------
|
|
0x00_0000_0000 .. 0x00_000F_FFFF Boot Rom
|
|
0x00_0100_0000 .. 0x00_0FFF_FFFF CCSR
|
|
0x00_1800_0000 .. 0x00_181F_FFFF OCRAM
|
|
0x00_3000_0000 .. 0x00_3FFF_FFFF IFC region #1
|
|
0x00_8000_0000 .. 0x00_FFFF_FFFF DDR region #1
|
|
0x05_1000_0000 .. 0x05_FFFF_FFFF IFC region #2
|
|
0x80_8000_0000 .. 0xFF_FFFF_FFFF DDR region #2
|
|
|
|
Other addresses are either reserved, or not used directly by U-Boot.
|
|
This list should be updated when more addresses are used.
|
|
|
|
IFC region map from core's view
|
|
-------------------------------
|
|
During boot i.e. IFC Region #1:-
|
|
0x30000000 - 0x37ffffff : 128MB : NOR flash
|
|
0x38000000 - 0x3BFFFFFF : 64MB : Promjet
|
|
0x3C000000 - 0x40000000 : 64MB : FPGA etc
|
|
|
|
After relocate to DDR i.e. IFC Region #2:-
|
|
0x5_1000_0000..0x5_1fff_ffff Memory Hole
|
|
0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
|
|
0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
|
|
0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
|
|
0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
|
|
|
|
Booting Options
|
|
---------------
|
|
a) Promjet Boot
|
|
b) NOR boot
|
|
c) NAND boot
|
|
d) SD boot
|
|
e) QSPI boot
|
|
|
|
Memory map for NOR boot
|
|
-------------------------
|
|
Image Flash Offset
|
|
RCW+PBI 0x00000000
|
|
Boot firmware (U-Boot) 0x00100000
|
|
Boot firmware Environment 0x00300000
|
|
PPA firmware 0x00400000
|
|
Secure Headers 0x00600000
|
|
DPAA2 MC 0x00A00000
|
|
DPAA2 DPL 0x00D00000
|
|
DPAA2 DPC 0x00E00000
|
|
Kernel.itb 0x01000000
|
|
|
|
Memory map for SD boot
|
|
-------------------------
|
|
Image Flash Offset SD Card
|
|
Start Block No.
|
|
RCW+PBI 0x00000000 0x00008
|
|
Boot firmware (U-Boot) 0x00100000 0x00800
|
|
Boot firmware Environment 0x00300000 0x01800
|
|
PPA firmware 0x00400000 0x02000
|
|
DPAA2 MC 0x00A00000 0x05000
|
|
DPAA2 DPL 0x00D00000 0x06800
|
|
DPAA2 DPC 0x00E00000 0x07000
|
|
Kernel.itb 0x01000000 0x08000
|
|
|
|
Environment Variables
|
|
---------------------
|
|
- mcboottimeout: MC boot timeout in milliseconds. If this variable is not defined
|
|
the value CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS will be assumed.
|
|
|
|
- mcmemsize: MC DRAM block size. If this variable is not defined
|
|
the value CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE will be assumed.
|
|
|
|
Booting Linux flavors which do not support 48-bit VA (< Linux 3.18)
|
|
-------------------------------------------------------------------
|
|
One needs to use appropriate bootargs to boot Linux flavors which do
|
|
not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown
|
|
below:
|
|
|
|
=> setenv bootargs 'console=ttyS1,115200 root=/dev/ram
|
|
earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m
|
|
hugepages=16 mem=2048M'
|
|
|
|
|
|
X-QSGMII-16PORT riser card
|
|
----------------------------
|
|
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
|
|
interfaces implemented in PCIe form factor board.
|
|
It supports following:
|
|
- Card can operate with up to 4 QSGMII lane simultaneously
|
|
- Card can operate with up to 8 SGMII lane simultaneously
|
|
|
|
Supported card configuration
|
|
- CSEL : ON ON ON ON
|
|
- MSEL1 : ON ON ON ON OFF OFF OFF OFF
|
|
- MSEL2 : OFF OFF OFF OFF ON ON ON ON
|
|
|
|
To enable this card: modify hwconfig to add "xqsgmii" variable.
|
|
|
|
Supported PHY addresses during SGMII:
|
|
#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
|
|
#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
|
|
#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
|
|
#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
|
|
#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
|
|
#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
|
|
#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
|
|
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
|
|
|
|
Mapping DPMACx to PHY during SGMII
|
|
DPMAC1 -> PHY1-P0
|
|
DPMAC2 -> PHY2-P0
|
|
DPMAC3 -> PHY3-P0
|
|
DPMAC4 -> PHY4-P0
|
|
DPMAC5 -> PHY3-P2
|
|
DPMAC6 -> PHY1-P2
|
|
DPMAC7 -> PHY4-P1
|
|
DPMAC8 -> PHY2-P2
|
|
DPMAC9 -> PHY1-P0
|
|
DPMAC10 -> PHY2-P0
|
|
DPMAC11 -> PHY3-P0
|
|
DPMAC12 -> PHY4-P0
|
|
DPMAC13 -> PHY3-P2
|
|
DPMAC14 -> PHY1-P2
|
|
DPMAC15 -> PHY4-P1
|
|
DPMAC16 -> PHY2-P2
|
|
|
|
|
|
Supported PHY address during QSGMII
|
|
#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
|
|
#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
|
|
#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
|
|
#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
|
|
#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
|
|
#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
|
|
#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
|
|
#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
|
|
#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
|
|
#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
|
|
#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
|
|
#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
|
|
#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
|
|
#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
|
|
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
|
|
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
|
|
|
|
Mapping DPMACx to PHY during QSGMII
|
|
DPMAC1 -> PHY1-P3
|
|
DPMAC2 -> PHY1-P2
|
|
DPMAC3 -> PHY1-P1
|
|
DPMAC4 -> PHY1-P0
|
|
DPMAC5 -> PHY2-P3
|
|
DPMAC6 -> PHY2-P2
|
|
DPMAC7 -> PHY2-P1
|
|
DPMAC8 -> PHY2-P0
|
|
DPMAC9 -> PHY3-P0
|
|
DPMAC10 -> PHY3-P1
|
|
DPMAC11 -> PHY3-P2
|
|
DPMAC12 -> PHY3-P3
|
|
DPMAC13 -> PHY4-P0
|
|
DPMAC14 -> PHY4-P1
|
|
DPMAC15 -> PHY4-P2
|
|
DPMAC16 -> PHY4-P3
|
|
|