mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-21 10:43:06 +00:00
c05ed00afb
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
838 lines
20 KiB
C
838 lines
20 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) Excito Elektronik i Skåne AB, All rights reserved.
|
|
* Author: Tor Krill <tor@excito.com>
|
|
*
|
|
* This is a driver for Silicon Image sil3114 sata chip modelled on
|
|
* the ata_piix driver
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <blk.h>
|
|
#include <log.h>
|
|
#include <part.h>
|
|
#include <pci.h>
|
|
#include <command.h>
|
|
#include <config.h>
|
|
#include <asm/byteorder.h>
|
|
#include <asm/io.h>
|
|
#include <ide.h>
|
|
#include <sata.h>
|
|
#include <libata.h>
|
|
#include <linux/delay.h>
|
|
#include "sata_sil3114.h"
|
|
|
|
/* Convert sectorsize to wordsize */
|
|
#define ATA_SECTOR_WORDS (ATA_SECT_SIZE/2)
|
|
|
|
/* Forwards */
|
|
u8 sil3114_spin_up (int num);
|
|
u8 sil3114_spin_down (int num);
|
|
static int sata_bus_softreset (int num);
|
|
static void sata_identify (int num, int dev);
|
|
static u8 check_power_mode (int num);
|
|
static void sata_port (struct sata_ioports *ioport);
|
|
static void set_Feature_cmd (int num, int dev);
|
|
static u8 sata_busy_wait (struct sata_ioports *ioaddr, int bits,
|
|
unsigned int max, u8 usealtstatus);
|
|
static u8 sata_chk_status (struct sata_ioports *ioaddr, u8 usealtstatus);
|
|
static void msleep (int count);
|
|
|
|
static u32 iobase[6] = { 0, 0, 0, 0, 0, 0}; /* PCI BAR registers for device */
|
|
|
|
static struct sata_port port[CONFIG_SYS_SATA_MAX_DEVICE];
|
|
|
|
static void output_data (struct sata_ioports *ioaddr, u16 * sect_buf, int words)
|
|
{
|
|
while (words--) {
|
|
__raw_writew (*sect_buf++, (void *)ioaddr->data_addr);
|
|
}
|
|
}
|
|
|
|
static int input_data (struct sata_ioports *ioaddr, u16 * sect_buf, int words)
|
|
{
|
|
while (words--) {
|
|
*sect_buf++ = __raw_readw ((void *)ioaddr->data_addr);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int sata_bus_softreset (int num)
|
|
{
|
|
u8 status = 0;
|
|
|
|
port[num].dev_mask = 1;
|
|
|
|
port[num].ctl_reg = 0x08; /*Default value of control reg */
|
|
writeb (port[num].ctl_reg, port[num].ioaddr.ctl_addr);
|
|
udelay(10);
|
|
writeb (port[num].ctl_reg | ATA_SRST, port[num].ioaddr.ctl_addr);
|
|
udelay(10);
|
|
writeb (port[num].ctl_reg, port[num].ioaddr.ctl_addr);
|
|
|
|
/* spec mandates ">= 2ms" before checking status.
|
|
* We wait 150ms, because that was the magic delay used for
|
|
* ATAPI devices in Hale Landis's ATADRVR, for the period of time
|
|
* between when the ATA command register is written, and then
|
|
* status is checked. Because waiting for "a while" before
|
|
* checking status is fine, post SRST, we perform this magic
|
|
* delay here as well.
|
|
*/
|
|
msleep (150);
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 300, 0);
|
|
while ((status & ATA_BUSY)) {
|
|
msleep (100);
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 3, 0);
|
|
}
|
|
|
|
if (status & ATA_BUSY) {
|
|
printf ("ata%u is slow to respond,plz be patient\n", num);
|
|
}
|
|
|
|
while ((status & ATA_BUSY)) {
|
|
msleep (100);
|
|
status = sata_chk_status (&port[num].ioaddr, 0);
|
|
}
|
|
|
|
if (status & ATA_BUSY) {
|
|
printf ("ata%u failed to respond : ", num);
|
|
printf ("bus reset failed\n");
|
|
port[num].dev_mask = 0;
|
|
return 1;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static void sata_identify (int num, int dev)
|
|
{
|
|
u8 cmd = 0, status = 0, devno = num;
|
|
u16 iobuf[ATA_SECTOR_WORDS];
|
|
u64 n_sectors = 0;
|
|
|
|
memset (iobuf, 0, sizeof (iobuf));
|
|
|
|
if (!(port[num].dev_mask & 0x01)) {
|
|
printf ("dev%d is not present on port#%d\n", dev, num);
|
|
return;
|
|
}
|
|
|
|
debug ("port=%d dev=%d\n", num, dev);
|
|
|
|
status = 0;
|
|
cmd = ATA_CMD_ID_ATA; /*Device Identify Command */
|
|
writeb (cmd, port[num].ioaddr.command_addr);
|
|
readb (port[num].ioaddr.altstatus_addr);
|
|
udelay(10);
|
|
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 1000, 0);
|
|
if (status & ATA_ERR) {
|
|
printf ("\ndevice not responding\n");
|
|
port[num].dev_mask &= ~0x01;
|
|
return;
|
|
}
|
|
|
|
input_data (&port[num].ioaddr, iobuf, ATA_SECTOR_WORDS);
|
|
|
|
ata_swap_buf_le16 (iobuf, ATA_SECTOR_WORDS);
|
|
|
|
debug ("Specific config: %x\n", iobuf[2]);
|
|
|
|
/* we require LBA and DMA support (bits 8 & 9 of word 49) */
|
|
if (!ata_id_has_dma (iobuf) || !ata_id_has_lba (iobuf)) {
|
|
debug ("ata%u: no dma/lba\n", num);
|
|
}
|
|
#ifdef DEBUG
|
|
ata_dump_id (iobuf);
|
|
#endif
|
|
n_sectors = ata_id_n_sectors (iobuf);
|
|
|
|
if (n_sectors == 0) {
|
|
port[num].dev_mask &= ~0x01;
|
|
return;
|
|
}
|
|
ata_id_c_string (iobuf, (unsigned char *)sata_dev_desc[devno].revision,
|
|
ATA_ID_FW_REV, sizeof (sata_dev_desc[devno].revision));
|
|
ata_id_c_string (iobuf, (unsigned char *)sata_dev_desc[devno].vendor,
|
|
ATA_ID_PROD, sizeof (sata_dev_desc[devno].vendor));
|
|
ata_id_c_string (iobuf, (unsigned char *)sata_dev_desc[devno].product,
|
|
ATA_ID_SERNO, sizeof (sata_dev_desc[devno].product));
|
|
|
|
/* TODO - atm we asume harddisk ie not removable */
|
|
sata_dev_desc[devno].removable = 0;
|
|
|
|
sata_dev_desc[devno].lba = (u32) n_sectors;
|
|
debug("lba=0x%lx\n", sata_dev_desc[devno].lba);
|
|
|
|
#ifdef CONFIG_LBA48
|
|
if (iobuf[83] & (1 << 10)) {
|
|
sata_dev_desc[devno].lba48 = 1;
|
|
} else {
|
|
sata_dev_desc[devno].lba48 = 0;
|
|
}
|
|
#endif
|
|
|
|
/* assuming HD */
|
|
sata_dev_desc[devno].type = DEV_TYPE_HARDDISK;
|
|
sata_dev_desc[devno].blksz = ATA_SECT_SIZE;
|
|
sata_dev_desc[devno].lun = 0; /* just to fill something in... */
|
|
}
|
|
|
|
static void set_Feature_cmd (int num, int dev)
|
|
{
|
|
u8 status = 0;
|
|
|
|
if (!(port[num].dev_mask & 0x01)) {
|
|
debug ("dev%d is not present on port#%d\n", dev, num);
|
|
return;
|
|
}
|
|
|
|
writeb (SETFEATURES_XFER, port[num].ioaddr.feature_addr);
|
|
writeb (XFER_PIO_4, port[num].ioaddr.nsect_addr);
|
|
writeb (0, port[num].ioaddr.lbal_addr);
|
|
writeb (0, port[num].ioaddr.lbam_addr);
|
|
writeb (0, port[num].ioaddr.lbah_addr);
|
|
|
|
writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr);
|
|
writeb (ATA_CMD_SET_FEATURES, port[num].ioaddr.command_addr);
|
|
|
|
udelay(50);
|
|
msleep (150);
|
|
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 5000, 0);
|
|
if ((status & (ATA_BUSY | ATA_ERR))) {
|
|
printf ("Error : status 0x%02x\n", status);
|
|
port[num].dev_mask &= ~0x01;
|
|
}
|
|
}
|
|
|
|
u8 sil3114_spin_down (int num)
|
|
{
|
|
u8 status = 0;
|
|
|
|
debug ("Spin down disk\n");
|
|
|
|
if (!(port[num].dev_mask & 0x01)) {
|
|
debug ("Device ata%d is not present\n", num);
|
|
return 1;
|
|
}
|
|
|
|
if ((status = check_power_mode (num)) == 0x00) {
|
|
debug ("Already in standby\n");
|
|
return 0;
|
|
}
|
|
|
|
if (status == 0x01) {
|
|
printf ("Failed to check power mode on ata%d\n", num);
|
|
return 1;
|
|
}
|
|
|
|
if (!((status = sata_chk_status (&port[num].ioaddr, 0)) & ATA_DRDY)) {
|
|
printf ("Device ata%d not ready\n", num);
|
|
return 1;
|
|
}
|
|
|
|
writeb (0x00, port[num].ioaddr.feature_addr);
|
|
|
|
writeb (0x00, port[num].ioaddr.nsect_addr);
|
|
writeb (0x00, port[num].ioaddr.lbal_addr);
|
|
writeb (0x00, port[num].ioaddr.lbam_addr);
|
|
writeb (0x00, port[num].ioaddr.lbah_addr);
|
|
|
|
writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr);
|
|
writeb (ATA_CMD_STANDBY, port[num].ioaddr.command_addr);
|
|
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 30000, 0);
|
|
if ((status & (ATA_BUSY | ATA_ERR))) {
|
|
printf ("Error waiting for disk spin down: status 0x%02x\n",
|
|
status);
|
|
port[num].dev_mask &= ~0x01;
|
|
return 1;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
u8 sil3114_spin_up (int num)
|
|
{
|
|
u8 status = 0;
|
|
|
|
debug ("Spin up disk\n");
|
|
|
|
if (!(port[num].dev_mask & 0x01)) {
|
|
debug ("Device ata%d is not present\n", num);
|
|
return 1;
|
|
}
|
|
|
|
if ((status = check_power_mode (num)) != 0x00) {
|
|
if (status == 0x01) {
|
|
printf ("Failed to check power mode on ata%d\n", num);
|
|
return 1;
|
|
} else {
|
|
/* should be up and running already */
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
if (!((status = sata_chk_status (&port[num].ioaddr, 0)) & ATA_DRDY)) {
|
|
printf ("Device ata%d not ready\n", num);
|
|
return 1;
|
|
}
|
|
|
|
debug ("Stautus of device check: %d\n", status);
|
|
|
|
writeb (0x00, port[num].ioaddr.feature_addr);
|
|
|
|
writeb (0x00, port[num].ioaddr.nsect_addr);
|
|
writeb (0x00, port[num].ioaddr.lbal_addr);
|
|
writeb (0x00, port[num].ioaddr.lbam_addr);
|
|
writeb (0x00, port[num].ioaddr.lbah_addr);
|
|
|
|
writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr);
|
|
writeb (ATA_CMD_IDLE, port[num].ioaddr.command_addr);
|
|
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 30000, 0);
|
|
if ((status & (ATA_BUSY | ATA_ERR))) {
|
|
printf ("Error waiting for disk spin up: status 0x%02x\n",
|
|
status);
|
|
port[num].dev_mask &= ~0x01;
|
|
return 1;
|
|
}
|
|
|
|
/* Wait for disk to enter Active state */
|
|
do {
|
|
msleep (10);
|
|
status = check_power_mode (num);
|
|
} while ((status == 0x00) || (status == 0x80));
|
|
|
|
if (status == 0x01) {
|
|
printf ("Falied waiting for disk to spin up\n");
|
|
return 1;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Return value is not the usual here
|
|
* 0x00 - Device stand by
|
|
* 0x01 - Operation failed
|
|
* 0x80 - Device idle
|
|
* 0xff - Device active
|
|
*/
|
|
static u8 check_power_mode (int num)
|
|
{
|
|
u8 status = 0;
|
|
u8 res = 0;
|
|
if (!(port[num].dev_mask & 0x01)) {
|
|
debug ("Device ata%d is not present\n", num);
|
|
return 1;
|
|
}
|
|
|
|
if (!(sata_chk_status (&port[num].ioaddr, 0) & ATA_DRDY)) {
|
|
printf ("Device ata%d not ready\n", num);
|
|
return 1;
|
|
}
|
|
|
|
writeb (0, port[num].ioaddr.feature_addr);
|
|
writeb (0, port[num].ioaddr.nsect_addr);
|
|
writeb (0, port[num].ioaddr.lbal_addr);
|
|
writeb (0, port[num].ioaddr.lbam_addr);
|
|
writeb (0, port[num].ioaddr.lbah_addr);
|
|
|
|
writeb (ATA_DEVICE_OBS, port[num].ioaddr.device_addr);
|
|
writeb (ATA_CMD_CHK_POWER, port[num].ioaddr.command_addr);
|
|
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 5000, 0);
|
|
if ((status & (ATA_BUSY | ATA_ERR))) {
|
|
printf
|
|
("Error waiting for check power mode complete : status 0x%02x\n",
|
|
status);
|
|
port[num].dev_mask &= ~0x01;
|
|
return 1;
|
|
}
|
|
res = readb (port[num].ioaddr.nsect_addr);
|
|
debug ("Check powermode: %d\n", res);
|
|
return res;
|
|
|
|
}
|
|
|
|
static void sata_port (struct sata_ioports *ioport)
|
|
{
|
|
ioport->data_addr = ioport->cmd_addr + ATA_REG_DATA;
|
|
ioport->error_addr = ioport->cmd_addr + ATA_REG_ERR;
|
|
ioport->feature_addr = ioport->cmd_addr + ATA_REG_FEATURE;
|
|
ioport->nsect_addr = ioport->cmd_addr + ATA_REG_NSECT;
|
|
ioport->lbal_addr = ioport->cmd_addr + ATA_REG_LBAL;
|
|
ioport->lbam_addr = ioport->cmd_addr + ATA_REG_LBAM;
|
|
ioport->lbah_addr = ioport->cmd_addr + ATA_REG_LBAH;
|
|
ioport->device_addr = ioport->cmd_addr + ATA_REG_DEVICE;
|
|
ioport->status_addr = ioport->cmd_addr + ATA_REG_STATUS;
|
|
ioport->command_addr = ioport->cmd_addr + ATA_REG_CMD;
|
|
}
|
|
|
|
static u8 wait_for_irq (int num, unsigned int max)
|
|
{
|
|
|
|
u32 port = iobase[5];
|
|
switch (num) {
|
|
case 0:
|
|
port += VND_TF_CNST_CH0;
|
|
break;
|
|
case 1:
|
|
port += VND_TF_CNST_CH1;
|
|
break;
|
|
case 2:
|
|
port += VND_TF_CNST_CH2;
|
|
break;
|
|
case 3:
|
|
port += VND_TF_CNST_CH3;
|
|
break;
|
|
default:
|
|
return 1;
|
|
}
|
|
|
|
do {
|
|
if (readl (port) & VND_TF_CNST_INTST) {
|
|
break;
|
|
}
|
|
udelay(1000);
|
|
max--;
|
|
} while ((max > 0));
|
|
|
|
return (max == 0);
|
|
}
|
|
|
|
static u8 sata_busy_wait (struct sata_ioports *ioaddr, int bits,
|
|
unsigned int max, u8 usealtstatus)
|
|
{
|
|
u8 status;
|
|
|
|
do {
|
|
if (!((status = sata_chk_status (ioaddr, usealtstatus)) & bits)) {
|
|
break;
|
|
}
|
|
udelay(1000);
|
|
max--;
|
|
} while ((status & bits) && (max > 0));
|
|
|
|
return status;
|
|
}
|
|
|
|
static u8 sata_chk_status (struct sata_ioports *ioaddr, u8 usealtstatus)
|
|
{
|
|
if (!usealtstatus) {
|
|
return readb (ioaddr->status_addr);
|
|
} else {
|
|
return readb (ioaddr->altstatus_addr);
|
|
}
|
|
}
|
|
|
|
static void msleep (int count)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < count; i++)
|
|
udelay(1000);
|
|
}
|
|
|
|
/* Read up to 255 sectors
|
|
*
|
|
* Returns sectors read
|
|
*/
|
|
static u8 do_one_read (int device, ulong block, u8 blkcnt, u16 * buff,
|
|
uchar lba48)
|
|
{
|
|
|
|
u8 sr = 0;
|
|
u8 status;
|
|
u64 blknr = (u64) block;
|
|
|
|
if (!(sata_chk_status (&port[device].ioaddr, 0) & ATA_DRDY)) {
|
|
printf ("Device ata%d not ready\n", device);
|
|
return 0;
|
|
}
|
|
|
|
/* Set up transfer */
|
|
#ifdef CONFIG_LBA48
|
|
if (lba48) {
|
|
/* write high bits */
|
|
writeb (0, port[device].ioaddr.nsect_addr);
|
|
writeb ((blknr >> 24) & 0xFF, port[device].ioaddr.lbal_addr);
|
|
writeb ((blknr >> 32) & 0xFF, port[device].ioaddr.lbam_addr);
|
|
writeb ((blknr >> 40) & 0xFF, port[device].ioaddr.lbah_addr);
|
|
}
|
|
#endif
|
|
writeb (blkcnt, port[device].ioaddr.nsect_addr);
|
|
writeb (((blknr) >> 0) & 0xFF, port[device].ioaddr.lbal_addr);
|
|
writeb ((blknr >> 8) & 0xFF, port[device].ioaddr.lbam_addr);
|
|
writeb ((blknr >> 16) & 0xFF, port[device].ioaddr.lbah_addr);
|
|
|
|
#ifdef CONFIG_LBA48
|
|
if (lba48) {
|
|
writeb (ATA_LBA, port[device].ioaddr.device_addr);
|
|
writeb (ATA_CMD_PIO_READ_EXT, port[device].ioaddr.command_addr);
|
|
} else
|
|
#endif
|
|
{
|
|
writeb (ATA_LBA | ((blknr >> 24) & 0xF),
|
|
port[device].ioaddr.device_addr);
|
|
writeb (ATA_CMD_PIO_READ, port[device].ioaddr.command_addr);
|
|
}
|
|
|
|
status = sata_busy_wait (&port[device].ioaddr, ATA_BUSY, 10000, 1);
|
|
|
|
if (status & ATA_BUSY) {
|
|
u8 err = 0;
|
|
|
|
printf ("Device %d not responding status %d\n", device, status);
|
|
err = readb (port[device].ioaddr.error_addr);
|
|
printf ("Error reg = 0x%x\n", err);
|
|
|
|
return (sr);
|
|
}
|
|
while (blkcnt--) {
|
|
|
|
if (wait_for_irq (device, 500)) {
|
|
printf ("ata%u irq failed\n", device);
|
|
return sr;
|
|
}
|
|
|
|
status = sata_chk_status (&port[device].ioaddr, 0);
|
|
if (status & ATA_ERR) {
|
|
printf ("ata%u error %d\n", device,
|
|
readb (port[device].ioaddr.error_addr));
|
|
return sr;
|
|
}
|
|
/* Read one sector */
|
|
input_data (&port[device].ioaddr, buff, ATA_SECTOR_WORDS);
|
|
buff += ATA_SECTOR_WORDS;
|
|
sr++;
|
|
|
|
}
|
|
return sr;
|
|
}
|
|
|
|
ulong sata_read (int device, ulong block, lbaint_t blkcnt, void *buff)
|
|
{
|
|
ulong n = 0, sread;
|
|
u16 *buffer = (u16 *) buff;
|
|
u8 status = 0;
|
|
u64 blknr = (u64) block;
|
|
unsigned char lba48 = 0;
|
|
|
|
#ifdef CONFIG_LBA48
|
|
if (blknr > 0xfffffff) {
|
|
if (!sata_dev_desc[device].lba48) {
|
|
printf ("Drive doesn't support 48-bit addressing\n");
|
|
return 0;
|
|
}
|
|
/* more than 28 bits used, use 48bit mode */
|
|
lba48 = 1;
|
|
}
|
|
#endif
|
|
|
|
while (blkcnt > 0) {
|
|
|
|
if (blkcnt > 255) {
|
|
sread = 255;
|
|
} else {
|
|
sread = blkcnt;
|
|
}
|
|
|
|
status = do_one_read (device, blknr, sread, buffer, lba48);
|
|
if (status != sread) {
|
|
printf ("Read failed\n");
|
|
return n;
|
|
}
|
|
|
|
blkcnt -= sread;
|
|
blknr += sread;
|
|
n += sread;
|
|
buffer += sread * ATA_SECTOR_WORDS;
|
|
}
|
|
return n;
|
|
}
|
|
|
|
ulong sata_write (int device, ulong block, lbaint_t blkcnt, const void *buff)
|
|
{
|
|
ulong n = 0;
|
|
u16 *buffer = (u16 *) buff;
|
|
unsigned char status = 0, num = 0;
|
|
u64 blknr = (u64) block;
|
|
#ifdef CONFIG_LBA48
|
|
unsigned char lba48 = 0;
|
|
|
|
if (blknr > 0xfffffff) {
|
|
if (!sata_dev_desc[device].lba48) {
|
|
printf ("Drive doesn't support 48-bit addressing\n");
|
|
return 0;
|
|
}
|
|
/* more than 28 bits used, use 48bit mode */
|
|
lba48 = 1;
|
|
}
|
|
#endif
|
|
/*Port Number */
|
|
num = device;
|
|
|
|
while (blkcnt-- > 0) {
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 500, 0);
|
|
if (status & ATA_BUSY) {
|
|
printf ("ata%u failed to respond\n", port[num].port_no);
|
|
return n;
|
|
}
|
|
#ifdef CONFIG_LBA48
|
|
if (lba48) {
|
|
/* write high bits */
|
|
writeb (0, port[num].ioaddr.nsect_addr);
|
|
writeb ((blknr >> 24) & 0xFF,
|
|
port[num].ioaddr.lbal_addr);
|
|
writeb ((blknr >> 32) & 0xFF,
|
|
port[num].ioaddr.lbam_addr);
|
|
writeb ((blknr >> 40) & 0xFF,
|
|
port[num].ioaddr.lbah_addr);
|
|
}
|
|
#endif
|
|
writeb (1, port[num].ioaddr.nsect_addr);
|
|
writeb ((blknr >> 0) & 0xFF, port[num].ioaddr.lbal_addr);
|
|
writeb ((blknr >> 8) & 0xFF, port[num].ioaddr.lbam_addr);
|
|
writeb ((blknr >> 16) & 0xFF, port[num].ioaddr.lbah_addr);
|
|
#ifdef CONFIG_LBA48
|
|
if (lba48) {
|
|
writeb (ATA_LBA, port[num].ioaddr.device_addr);
|
|
writeb (ATA_CMD_PIO_WRITE_EXT, port[num].ioaddr.command_addr);
|
|
} else
|
|
#endif
|
|
{
|
|
writeb (ATA_LBA | ((blknr >> 24) & 0xF),
|
|
port[num].ioaddr.device_addr);
|
|
writeb (ATA_CMD_PIO_WRITE, port[num].ioaddr.command_addr);
|
|
}
|
|
|
|
msleep (50);
|
|
/*may take up to 4 sec */
|
|
status = sata_busy_wait (&port[num].ioaddr, ATA_BUSY, 4000, 0);
|
|
if ((status & (ATA_DRQ | ATA_BUSY | ATA_ERR)) != ATA_DRQ) {
|
|
printf ("Error no DRQ dev %d blk %ld: sts 0x%02x\n",
|
|
device, (ulong) blknr, status);
|
|
return (n);
|
|
}
|
|
|
|
output_data (&port[num].ioaddr, buffer, ATA_SECTOR_WORDS);
|
|
readb (port[num].ioaddr.altstatus_addr);
|
|
udelay(50);
|
|
|
|
++n;
|
|
++blknr;
|
|
buffer += ATA_SECTOR_WORDS;
|
|
}
|
|
return n;
|
|
}
|
|
|
|
/* Driver implementation */
|
|
static u8 sil_get_device_cache_line (pci_dev_t pdev)
|
|
{
|
|
u8 cache_line = 0;
|
|
pci_read_config_byte (pdev, PCI_CACHE_LINE_SIZE, &cache_line);
|
|
return cache_line;
|
|
}
|
|
|
|
int init_sata (int dev)
|
|
{
|
|
static u8 init_done = 0;
|
|
static int res = 1;
|
|
pci_dev_t devno;
|
|
u8 cls = 0;
|
|
u16 cmd = 0;
|
|
u32 sconf = 0;
|
|
|
|
if (init_done) {
|
|
return res;
|
|
}
|
|
|
|
init_done = 1;
|
|
|
|
if ((devno = pci_find_device (SIL_VEND_ID, SIL3114_DEVICE_ID, 0)) == -1) {
|
|
res = 1;
|
|
return res;
|
|
}
|
|
|
|
/* Read out all BARs, even though we only use MMIO from BAR5 */
|
|
pci_read_config_dword (devno, PCI_BASE_ADDRESS_0, &iobase[0]);
|
|
pci_read_config_dword (devno, PCI_BASE_ADDRESS_1, &iobase[1]);
|
|
pci_read_config_dword (devno, PCI_BASE_ADDRESS_2, &iobase[2]);
|
|
pci_read_config_dword (devno, PCI_BASE_ADDRESS_3, &iobase[3]);
|
|
pci_read_config_dword (devno, PCI_BASE_ADDRESS_4, &iobase[4]);
|
|
pci_read_config_dword (devno, PCI_BASE_ADDRESS_5, &iobase[5]);
|
|
|
|
if ((iobase[0] == 0xFFFFFFFF) || (iobase[1] == 0xFFFFFFFF) ||
|
|
(iobase[2] == 0xFFFFFFFF) || (iobase[3] == 0xFFFFFFFF) ||
|
|
(iobase[4] == 0xFFFFFFFF) || (iobase[5] == 0xFFFFFFFF)) {
|
|
printf ("Error no base addr for SATA controller\n");
|
|
res = 1;
|
|
return res;
|
|
}
|
|
|
|
/* mask off unused bits */
|
|
iobase[0] &= 0xfffffffc;
|
|
iobase[1] &= 0xfffffff8;
|
|
iobase[2] &= 0xfffffffc;
|
|
iobase[3] &= 0xfffffff8;
|
|
iobase[4] &= 0xfffffff0;
|
|
iobase[5] &= 0xfffffc00;
|
|
|
|
/* from sata_sil in Linux kernel */
|
|
cls = sil_get_device_cache_line (devno);
|
|
if (cls) {
|
|
cls >>= 3;
|
|
cls++; /* cls = (line_size/8)+1 */
|
|
writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH0);
|
|
writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH1);
|
|
writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH2);
|
|
writel (cls << 8 | cls, iobase[5] + VND_FIFOCFG_CH3);
|
|
} else {
|
|
printf ("Cache line not set. Driver may not function\n");
|
|
}
|
|
|
|
/* Enable operation */
|
|
pci_read_config_word (devno, PCI_COMMAND, &cmd);
|
|
cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_IO | PCI_COMMAND_MEMORY;
|
|
pci_write_config_word (devno, PCI_COMMAND, cmd);
|
|
|
|
/* Disable interrupt usage */
|
|
pci_read_config_dword (devno, VND_SYSCONFSTAT, &sconf);
|
|
sconf |= (VND_SYSCONFSTAT_CHN_0_INTBLOCK | VND_SYSCONFSTAT_CHN_1_INTBLOCK);
|
|
pci_write_config_dword (devno, VND_SYSCONFSTAT, sconf);
|
|
|
|
res = 0;
|
|
return res;
|
|
}
|
|
|
|
int reset_sata(int dev)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
/* Check if device is connected to port */
|
|
int sata_bus_probe (int portno)
|
|
{
|
|
u32 port = iobase[5];
|
|
u32 val;
|
|
switch (portno) {
|
|
case 0:
|
|
port += VND_SSTATUS_CH0;
|
|
break;
|
|
case 1:
|
|
port += VND_SSTATUS_CH1;
|
|
break;
|
|
case 2:
|
|
port += VND_SSTATUS_CH2;
|
|
break;
|
|
case 3:
|
|
port += VND_SSTATUS_CH3;
|
|
break;
|
|
default:
|
|
return 0;
|
|
}
|
|
val = readl (port);
|
|
if ((val & SATA_DET_PRES) == SATA_DET_PRES) {
|
|
return 1;
|
|
} else {
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
int sata_phy_reset (int portno)
|
|
{
|
|
u32 port = iobase[5];
|
|
u32 val;
|
|
switch (portno) {
|
|
case 0:
|
|
port += VND_SCONTROL_CH0;
|
|
break;
|
|
case 1:
|
|
port += VND_SCONTROL_CH1;
|
|
break;
|
|
case 2:
|
|
port += VND_SCONTROL_CH2;
|
|
break;
|
|
case 3:
|
|
port += VND_SCONTROL_CH3;
|
|
break;
|
|
default:
|
|
return 0;
|
|
}
|
|
val = readl (port);
|
|
writel (val | SATA_SC_DET_RST, port);
|
|
msleep (150);
|
|
writel (val & ~SATA_SC_DET_RST, port);
|
|
return 0;
|
|
}
|
|
|
|
int scan_sata (int dev)
|
|
{
|
|
/* A bit brain dead, but the code has a legacy */
|
|
switch (dev) {
|
|
case 0:
|
|
port[0].port_no = 0;
|
|
port[0].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH0;
|
|
port[0].ioaddr.altstatus_addr = port[0].ioaddr.ctl_addr =
|
|
(iobase[5] + VND_TF2_CH0) | ATA_PCI_CTL_OFS;
|
|
port[0].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH0;
|
|
break;
|
|
#if (CONFIG_SYS_SATA_MAX_DEVICE >= 1)
|
|
case 1:
|
|
port[1].port_no = 0;
|
|
port[1].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH1;
|
|
port[1].ioaddr.altstatus_addr = port[1].ioaddr.ctl_addr =
|
|
(iobase[5] + VND_TF2_CH1) | ATA_PCI_CTL_OFS;
|
|
port[1].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH1;
|
|
break;
|
|
#elif (CONFIG_SYS_SATA_MAX_DEVICE >= 2)
|
|
case 2:
|
|
port[2].port_no = 0;
|
|
port[2].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH2;
|
|
port[2].ioaddr.altstatus_addr = port[2].ioaddr.ctl_addr =
|
|
(iobase[5] + VND_TF2_CH2) | ATA_PCI_CTL_OFS;
|
|
port[2].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH2;
|
|
break;
|
|
#elif (CONFIG_SYS_SATA_MAX_DEVICE >= 3)
|
|
case 3:
|
|
port[3].port_no = 0;
|
|
port[3].ioaddr.cmd_addr = iobase[5] + VND_TF0_CH3;
|
|
port[3].ioaddr.altstatus_addr = port[3].ioaddr.ctl_addr =
|
|
(iobase[5] + VND_TF2_CH3) | ATA_PCI_CTL_OFS;
|
|
port[3].ioaddr.bmdma_addr = iobase[5] + VND_BMDMA_CH3;
|
|
break;
|
|
#endif
|
|
default:
|
|
printf ("Tried to scan unknown port: ata%d\n", dev);
|
|
return 1;
|
|
}
|
|
|
|
/* Initialize other registers */
|
|
sata_port (&port[dev].ioaddr);
|
|
|
|
/* Check for attached device */
|
|
if (!sata_bus_probe (dev)) {
|
|
port[dev].port_state = 0;
|
|
debug ("SATA#%d port is not present\n", dev);
|
|
} else {
|
|
debug ("SATA#%d port is present\n", dev);
|
|
if (sata_bus_softreset (dev)) {
|
|
/* soft reset failed, try a hard one */
|
|
sata_phy_reset (dev);
|
|
if (sata_bus_softreset (dev)) {
|
|
port[dev].port_state = 0;
|
|
} else {
|
|
port[dev].port_state = 1;
|
|
}
|
|
} else {
|
|
port[dev].port_state = 1;
|
|
}
|
|
}
|
|
if (port[dev].port_state == 1) {
|
|
/* Probe device and set xfer mode */
|
|
sata_identify (dev, 0);
|
|
set_Feature_cmd (dev, 0);
|
|
}
|
|
|
|
return 0;
|
|
}
|