u-boot/arch/arm/cpu/armv7/start.S
Simon Glass b5bd09820c arm: Allow skipping of low-level init with I-cache on
At present CONFIG_SKIP_LOWLEVEL_INIT prevents U-Boot from calling
lowlevel_init(). This means that the instruction cache is not enabled and
the board runs very slowly.

What is really needed in many cases is to skip the call to lowlevel_init()
but still perform CP15 init. Add an option to handle this.

Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00

274 lines
8.2 KiB
ArmAsm

/*
* armboot - Startup Code for OMAP3530/ARM Cortex CPU-core
*
* Copyright (c) 2004 Texas Instruments <r-woodruff2@ti.com>
*
* Copyright (c) 2001 Marius Gröger <mag@sysgo.de>
* Copyright (c) 2002 Alex Züpke <azu@sysgo.de>
* Copyright (c) 2002 Gary Jennejohn <garyj@denx.de>
* Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com>
* Copyright (c) 2003 Kshitij <kshitij@ti.com>
* Copyright (c) 2006-2008 Syed Mohammed Khasim <x0khasim@ti.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm-offsets.h>
#include <config.h>
#include <asm/system.h>
#include <linux/linkage.h>
/*************************************************************************
*
* Startup Code (reset vector)
*
* Do important init only if we don't start from memory!
* Setup memory and board specific bits prior to relocation.
* Relocate armboot to ram. Setup stack.
*
*************************************************************************/
.globl reset
.globl save_boot_params_ret
reset:
/* Allow the board to save important registers */
b save_boot_params
save_boot_params_ret:
/*
* disable interrupts (FIQ and IRQ), also set the cpu to SVC32 mode,
* except if in HYP mode already
*/
mrs r0, cpsr
and r1, r0, #0x1f @ mask mode bits
teq r1, #0x1a @ test for HYP mode
bicne r0, r0, #0x1f @ clear all mode bits
orrne r0, r0, #0x13 @ set SVC mode
orr r0, r0, #0xc0 @ disable FIQ and IRQ
msr cpsr,r0
/*
* Setup vector:
* (OMAP4 spl TEXT_BASE is not 32 byte aligned.
* Continue to use ROM code vector only in OMAP4 spl)
*/
#if !(defined(CONFIG_OMAP44XX) && defined(CONFIG_SPL_BUILD))
/* Set V=0 in CP15 SCTLR register - for VBAR to point to vector */
mrc p15, 0, r0, c1, c0, 0 @ Read CP15 SCTLR Register
bic r0, #CR_V @ V = 0
mcr p15, 0, r0, c1, c0, 0 @ Write CP15 SCTLR Register
/* Set vector address in CP15 VBAR register */
ldr r0, =_start
mcr p15, 0, r0, c12, c0, 0 @Set VBAR
#endif
/* the mask ROM code should have PLL and others stable */
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_cp15
#ifndef CONFIG_SKIP_LOWLEVEL_INIT_ONLY
bl cpu_init_crit
#endif
#endif
bl _main
/*------------------------------------------------------------------------------*/
ENTRY(c_runtime_cpu_setup)
/*
* If I-cache is enabled invalidate it
*/
#ifndef CONFIG_SYS_ICACHE_OFF
mcr p15, 0, r0, c7, c5, 0 @ invalidate icache
mcr p15, 0, r0, c7, c10, 4 @ DSB
mcr p15, 0, r0, c7, c5, 4 @ ISB
#endif
bx lr
ENDPROC(c_runtime_cpu_setup)
/*************************************************************************
*
* void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3)
* __attribute__((weak));
*
* Stack pointer is not yet initialized at this moment
* Don't save anything to stack even if compiled with -O0
*
*************************************************************************/
ENTRY(save_boot_params)
b save_boot_params_ret @ back to my caller
ENDPROC(save_boot_params)
.weak save_boot_params
/*************************************************************************
*
* cpu_init_cp15
*
* Setup CP15 registers (cache, MMU, TLBs). The I-cache is turned on unless
* CONFIG_SYS_ICACHE_OFF is defined.
*
*************************************************************************/
ENTRY(cpu_init_cp15)
/*
* Invalidate L1 I/D
*/
mov r0, #0 @ set up for MCR
mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs
mcr p15, 0, r0, c7, c5, 0 @ invalidate icache
mcr p15, 0, r0, c7, c5, 6 @ invalidate BP array
mcr p15, 0, r0, c7, c10, 4 @ DSB
mcr p15, 0, r0, c7, c5, 4 @ ISB
/*
* disable MMU stuff and caches
*/
mrc p15, 0, r0, c1, c0, 0
bic r0, r0, #0x00002000 @ clear bits 13 (--V-)
bic r0, r0, #0x00000007 @ clear bits 2:0 (-CAM)
orr r0, r0, #0x00000002 @ set bit 1 (--A-) Align
orr r0, r0, #0x00000800 @ set bit 11 (Z---) BTB
#ifdef CONFIG_SYS_ICACHE_OFF
bic r0, r0, #0x00001000 @ clear bit 12 (I) I-cache
#else
orr r0, r0, #0x00001000 @ set bit 12 (I) I-cache
#endif
mcr p15, 0, r0, c1, c0, 0
#ifdef CONFIG_ARM_ERRATA_716044
mrc p15, 0, r0, c1, c0, 0 @ read system control register
orr r0, r0, #1 << 11 @ set bit #11
mcr p15, 0, r0, c1, c0, 0 @ write system control register
#endif
#if (defined(CONFIG_ARM_ERRATA_742230) || defined(CONFIG_ARM_ERRATA_794072))
mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
orr r0, r0, #1 << 4 @ set bit #4
mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
#endif
#ifdef CONFIG_ARM_ERRATA_743622
mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
orr r0, r0, #1 << 6 @ set bit #6
mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
#endif
#ifdef CONFIG_ARM_ERRATA_751472
mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
orr r0, r0, #1 << 11 @ set bit #11
mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
#endif
#ifdef CONFIG_ARM_ERRATA_761320
mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register
orr r0, r0, #1 << 21 @ set bit #21
mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
#endif
mov r5, lr @ Store my Caller
mrc p15, 0, r1, c0, c0, 0 @ r1 has Read Main ID Register (MIDR)
mov r3, r1, lsr #20 @ get variant field
and r3, r3, #0xf @ r3 has CPU variant
and r4, r1, #0xf @ r4 has CPU revision
mov r2, r3, lsl #4 @ shift variant field for combined value
orr r2, r4, r2 @ r2 has combined CPU variant + revision
#ifdef CONFIG_ARM_ERRATA_798870
cmp r2, #0x30 @ Applies to lower than R3p0
bge skip_errata_798870 @ skip if not affected rev
cmp r2, #0x20 @ Applies to including and above R2p0
blt skip_errata_798870 @ skip if not affected rev
mrc p15, 1, r0, c15, c0, 0 @ read l2 aux ctrl reg
orr r0, r0, #1 << 7 @ Enable hazard-detect timeout
push {r1-r5} @ Save the cpu info registers
bl v7_arch_cp15_set_l2aux_ctrl
isb @ Recommended ISB after l2actlr update
pop {r1-r5} @ Restore the cpu info - fall through
skip_errata_798870:
#endif
#ifdef CONFIG_ARM_ERRATA_801819
cmp r2, #0x24 @ Applies to lt including R2p4
bgt skip_errata_801819 @ skip if not affected rev
cmp r2, #0x20 @ Applies to including and above R2p0
blt skip_errata_801819 @ skip if not affected rev
mrc p15, 0, r0, c0, c0, 6 @ pick up REVIDR reg
and r0, r0, #1 << 3 @ check REVIDR[3]
cmp r0, #1 << 3
beq skip_errata_801819 @ skip erratum if REVIDR[3] is set
mrc p15, 0, r0, c1, c0, 1 @ read auxilary control register
orr r0, r0, #3 << 27 @ Disables streaming. All write-allocate
@ lines allocate in the L1 or L2 cache.
orr r0, r0, #3 << 25 @ Disables streaming. All write-allocate
@ lines allocate in the L1 cache.
push {r1-r5} @ Save the cpu info registers
bl v7_arch_cp15_set_acr
pop {r1-r5} @ Restore the cpu info - fall through
skip_errata_801819:
#endif
#ifdef CONFIG_ARM_ERRATA_454179
cmp r2, #0x21 @ Only on < r2p1
bge skip_errata_454179
mrc p15, 0, r0, c1, c0, 1 @ Read ACR
orr r0, r0, #(0x3 << 6) @ Set DBSM(BIT7) and IBE(BIT6) bits
push {r1-r5} @ Save the cpu info registers
bl v7_arch_cp15_set_acr
pop {r1-r5} @ Restore the cpu info - fall through
skip_errata_454179:
#endif
#ifdef CONFIG_ARM_ERRATA_430973
cmp r2, #0x21 @ Only on < r2p1
bge skip_errata_430973
mrc p15, 0, r0, c1, c0, 1 @ Read ACR
orr r0, r0, #(0x1 << 6) @ Set IBE bit
push {r1-r5} @ Save the cpu info registers
bl v7_arch_cp15_set_acr
pop {r1-r5} @ Restore the cpu info - fall through
skip_errata_430973:
#endif
#ifdef CONFIG_ARM_ERRATA_621766
cmp r2, #0x21 @ Only on < r2p1
bge skip_errata_621766
mrc p15, 0, r0, c1, c0, 1 @ Read ACR
orr r0, r0, #(0x1 << 5) @ Set L1NEON bit
push {r1-r5} @ Save the cpu info registers
bl v7_arch_cp15_set_acr
pop {r1-r5} @ Restore the cpu info - fall through
skip_errata_621766:
#endif
mov pc, r5 @ back to my caller
ENDPROC(cpu_init_cp15)
#if !defined(CONFIG_SKIP_LOWLEVEL_INIT) && \
!defined(CONFIG_SKIP_LOWLEVEL_INIT_ONLY)
/*************************************************************************
*
* CPU_init_critical registers
*
* setup important registers
* setup memory timing
*
*************************************************************************/
ENTRY(cpu_init_crit)
/*
* Jump to board specific initialization...
* The Mask ROM will have already initialized
* basic memory. Go here to bump up clock rate and handle
* wake up conditions.
*/
b lowlevel_init @ go setup pll,mux,memory
ENDPROC(cpu_init_crit)
#endif