mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 19:10:13 +00:00
1ea11e8138
The commit a4180c3696
("arm64: zynqmp: Add mode-pin GPIO controller DT
node") added usb phy reset over bootmode pins by default on usb0 only.
zcu100 is using usb0 as peripheral and usb1 as host. Unfortunately reset
line is shared for both usb ulpi phys but usb_rst_b is connected to usb5744
hub which is used only in host mode. Especially this chip requires reset to
operate properly that's why better assign gpio reset to usb1 instead of
usb0.
Without this change usb start crashed when runs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1ca80ec5bf7a595c03822f3e4e3683298205067a.1688992653.git.michal.simek@amd.com
618 lines
12 KiB
Text
618 lines
12 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* dts file for Xilinx ZynqMP ZCU100 revC
|
|
*
|
|
* (C) Copyright 2016 - 2021, Xilinx, Inc.
|
|
*
|
|
* Michal Simek <michal.simek@amd.com>
|
|
* Nathalie Chan King Choy
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "zynqmp.dtsi"
|
|
#include "zynqmp-clk-ccf.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
|
|
#include <dt-bindings/phy/phy.h>
|
|
|
|
/ {
|
|
model = "ZynqMP ZCU100 RevC";
|
|
compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp";
|
|
|
|
aliases {
|
|
i2c0 = &i2c1;
|
|
rtc0 = &rtc;
|
|
serial0 = &uart1;
|
|
serial1 = &uart0;
|
|
serial2 = &dcc;
|
|
spi0 = &spi0;
|
|
spi1 = &spi1;
|
|
usb0 = &usb0;
|
|
usb1 = &usb1;
|
|
mmc0 = &sdhci0;
|
|
mmc1 = &sdhci1;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "earlycon";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x0 0x0 0x80000000>;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
autorepeat;
|
|
switch-4 {
|
|
label = "sw4";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_POWER>;
|
|
wakeup-source;
|
|
autorepeat;
|
|
};
|
|
};
|
|
|
|
iio-hwmon {
|
|
compatible = "iio-hwmon";
|
|
io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
|
|
<&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>,
|
|
<&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>,
|
|
<&xilinx_ams 9>, <&xilinx_ams 10>,
|
|
<&xilinx_ams 11>, <&xilinx_ams 12>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
led-ds2 {
|
|
label = "ds2";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
led-ds3 {
|
|
label = "ds3";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tx"; /* WLAN tx */
|
|
default-state = "off";
|
|
};
|
|
|
|
led-ds4 {
|
|
label = "ds4";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0rx"; /* WLAN rx */
|
|
default-state = "off";
|
|
};
|
|
|
|
led-ds5 {
|
|
label = "ds5";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "bluetooth-power";
|
|
};
|
|
|
|
led-vbus-det { /* U5 USB5744 VBUS detection via MIO25 */
|
|
label = "vbus_det";
|
|
gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
ltc2954: ltc2954 { /* U7 */
|
|
compatible = "lltc,ltc2954", "lltc,ltc2952";
|
|
status = "disabled";
|
|
trigger-gpios = <&gpio 26 GPIO_ACTIVE_LOW>; /* INT line - input */
|
|
/* If there is HW watchdog on mezzanine this signal should be connected there */
|
|
watchdog-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; /* MIO on PAD */
|
|
kill-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; /* KILL signal - output */
|
|
};
|
|
|
|
wmmcsdio_fixed: fixedregulator-mmcsdio {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "wmmcsdio_fixed";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
sdio_pwrseq: sdio-pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
|
|
post-power-on-delay-ms = <10>;
|
|
};
|
|
|
|
ina226 {
|
|
compatible = "iio-hwmon";
|
|
io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
|
|
};
|
|
|
|
si5335_0: si5335_0 { /* clk0_usb - u23 */
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <26000000>;
|
|
};
|
|
|
|
si5335_1: si5335_1 { /* clk1_dp - u23 */
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <27000000>;
|
|
};
|
|
};
|
|
|
|
&dcc {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL",
|
|
"I2C1_SDA", "SPI1_SCLK", "WLAN_EN", "BT_EN", "SPI1_CS",
|
|
"SPI1_MISO", "SPI1_MOSI", "I2C_MUX_RESET", "SD0_DAT0", "SD0_DAT1",
|
|
"SD0_DAT2", "SD0_DAT3", "PS_LED3", "PS_LED2", "PS_LED1",
|
|
"PS_LED0", "SD0_CMD", "SD0_CLK", "GPIO_PB", "SD0_DETECT",
|
|
"VBUS_DET", "POWER_INT", "DP_AUX", "DP_HPD", "DP_OE",
|
|
"DP_AUX_IN", "INA226_ALERT", "PS_FP_PWR_EN", "PL_PWR_EN", "POWER_KILL",
|
|
"", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C",
|
|
"GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E",
|
|
"GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3",
|
|
"SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2",
|
|
"USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3",
|
|
"USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK",
|
|
"USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1",
|
|
"USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6",
|
|
"USB_DATA7", "WLAN_IRQ", "PMIC_IRQ", /* MIO end and EMIO start */
|
|
"", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
&gpu {
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c1_default>;
|
|
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
|
scl-gpios = <&gpio 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
clock-frequency = <100000>;
|
|
i2c-mux@75 { /* u11 */
|
|
compatible = "nxp,pca9548";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x75>;
|
|
i2csw_0: i2c@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0>;
|
|
label = "LS-I2C0";
|
|
};
|
|
i2csw_1: i2c@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>;
|
|
label = "LS-I2C1";
|
|
};
|
|
i2csw_2: i2c@2 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <2>;
|
|
label = "HS-I2C2";
|
|
};
|
|
i2csw_3: i2c@3 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <3>;
|
|
label = "HS-I2C3";
|
|
};
|
|
i2csw_4: i2c@4 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x4>;
|
|
|
|
pmic: pmic@5e { /* Custom TI PMIC u33 */
|
|
compatible = "ti,tps65086";
|
|
reg = <0x5e>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <77 IRQ_TYPE_LEVEL_LOW>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
};
|
|
i2csw_5: i2c@5 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <5>;
|
|
/* PS_PMBUS */
|
|
u35: ina226@40 { /* u35 */
|
|
compatible = "ti,ina226";
|
|
#io-channel-cells = <1>;
|
|
reg = <0x40>;
|
|
shunt-resistor = <10000>;
|
|
/* MIO31 is alert which should be routed to PMUFW */
|
|
};
|
|
};
|
|
i2csw_6: i2c@6 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <6>;
|
|
/*
|
|
* Not Connected
|
|
*/
|
|
};
|
|
i2csw_7: i2c@7 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <7>;
|
|
/*
|
|
* usb5744 (DNP) - U5
|
|
* 100kHz - this is default freq for us
|
|
*/
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinctrl0 {
|
|
status = "okay";
|
|
pinctrl_i2c1_default: i2c1-default {
|
|
mux {
|
|
groups = "i2c1_1_grp";
|
|
function = "i2c1";
|
|
};
|
|
|
|
conf {
|
|
groups = "i2c1_1_grp";
|
|
bias-pull-up;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
};
|
|
|
|
pinctrl_i2c1_gpio: i2c1-gpio {
|
|
mux {
|
|
groups = "gpio0_4_grp", "gpio0_5_grp";
|
|
function = "gpio0";
|
|
};
|
|
|
|
conf {
|
|
groups = "gpio0_4_grp", "gpio0_5_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
};
|
|
|
|
pinctrl_sdhci0_default: sdhci0-default {
|
|
mux {
|
|
groups = "sdio0_3_grp";
|
|
function = "sdio0";
|
|
};
|
|
|
|
conf {
|
|
groups = "sdio0_3_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
bias-disable;
|
|
};
|
|
|
|
mux-cd {
|
|
groups = "sdio0_cd_0_grp";
|
|
function = "sdio0_cd";
|
|
};
|
|
|
|
conf-cd {
|
|
groups = "sdio0_cd_0_grp";
|
|
bias-high-impedance;
|
|
bias-pull-up;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
};
|
|
|
|
pinctrl_sdhci1_default: sdhci1-default {
|
|
mux {
|
|
groups = "sdio1_2_grp";
|
|
function = "sdio1";
|
|
};
|
|
|
|
conf {
|
|
groups = "sdio1_2_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_spi0_default: spi0-default {
|
|
mux {
|
|
groups = "spi0_3_grp";
|
|
function = "spi0";
|
|
};
|
|
|
|
conf {
|
|
groups = "spi0_3_grp";
|
|
bias-disable;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
mux-cs {
|
|
groups = "spi0_ss_9_grp";
|
|
function = "spi0_ss";
|
|
};
|
|
|
|
conf-cs {
|
|
groups = "spi0_ss_9_grp";
|
|
bias-disable;
|
|
};
|
|
|
|
};
|
|
|
|
pinctrl_spi1_default: spi1-default {
|
|
mux {
|
|
groups = "spi1_0_grp";
|
|
function = "spi1";
|
|
};
|
|
|
|
conf {
|
|
groups = "spi1_0_grp";
|
|
bias-disable;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
mux-cs {
|
|
groups = "spi1_ss_0_grp";
|
|
function = "spi1_ss";
|
|
};
|
|
|
|
conf-cs {
|
|
groups = "spi1_ss_0_grp";
|
|
bias-disable;
|
|
};
|
|
|
|
};
|
|
|
|
pinctrl_uart0_default: uart0-default {
|
|
mux {
|
|
groups = "uart0_0_grp";
|
|
function = "uart0";
|
|
};
|
|
|
|
conf {
|
|
groups = "uart0_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO3";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO2";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_uart1_default: uart1-default {
|
|
mux {
|
|
groups = "uart1_0_grp";
|
|
function = "uart1";
|
|
};
|
|
|
|
conf {
|
|
groups = "uart1_0_grp";
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO1";
|
|
bias-high-impedance;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO0";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_usb0_default: usb0-default {
|
|
mux {
|
|
groups = "usb0_0_grp";
|
|
function = "usb0";
|
|
};
|
|
|
|
conf {
|
|
groups = "usb0_0_grp";
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO52", "MIO53", "MIO55";
|
|
bias-high-impedance;
|
|
drive-strength = <12>;
|
|
slew-rate = <SLEW_RATE_FAST>;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
|
|
"MIO60", "MIO61", "MIO62", "MIO63";
|
|
bias-disable;
|
|
drive-strength = <4>;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
};
|
|
};
|
|
|
|
pinctrl_usb1_default: usb1-default {
|
|
mux {
|
|
groups = "usb1_0_grp";
|
|
function = "usb1";
|
|
};
|
|
|
|
conf {
|
|
groups = "usb1_0_grp";
|
|
power-source = <IO_STANDARD_LVCMOS18>;
|
|
};
|
|
|
|
conf-rx {
|
|
pins = "MIO64", "MIO65", "MIO67";
|
|
bias-high-impedance;
|
|
drive-strength = <12>;
|
|
slew-rate = <SLEW_RATE_FAST>;
|
|
};
|
|
|
|
conf-tx {
|
|
pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
|
|
"MIO72", "MIO73", "MIO74", "MIO75";
|
|
bias-disable;
|
|
drive-strength = <4>;
|
|
slew-rate = <SLEW_RATE_SLOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&psgtr {
|
|
status = "okay";
|
|
/* usb3, dp */
|
|
clocks = <&si5335_0>, <&si5335_1>;
|
|
clock-names = "ref0", "ref1";
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
/* SD0 only supports 3.3V, no level shifter */
|
|
&sdhci0 {
|
|
status = "okay";
|
|
no-1-8-v;
|
|
disable-wp;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_sdhci0_default>;
|
|
xlnx,mio-bank = <0>;
|
|
};
|
|
|
|
&sdhci1 {
|
|
status = "okay";
|
|
bus-width = <0x4>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_sdhci1_default>;
|
|
xlnx,mio-bank = <0>;
|
|
non-removable;
|
|
disable-wp;
|
|
cap-power-off-card;
|
|
mmc-pwrseq = <&sdio_pwrseq>;
|
|
vqmmc-supply = <&wmmcsdio_fixed>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
wlcore: wifi@2 {
|
|
compatible = "ti,wl1831";
|
|
reg = <2>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */
|
|
};
|
|
};
|
|
|
|
&spi0 { /* Low Speed connector */
|
|
status = "okay";
|
|
label = "LS-SPI0";
|
|
num-cs = <1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_spi0_default>;
|
|
};
|
|
|
|
&spi1 { /* High Speed connector */
|
|
status = "okay";
|
|
label = "HS-SPI1";
|
|
num-cs = <1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_spi1_default>;
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart0_default>;
|
|
bluetooth {
|
|
compatible = "ti,wl1831-st";
|
|
enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart1_default>;
|
|
};
|
|
|
|
/* ULPI SMSC USB3320 */
|
|
&usb0 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usb0_default>;
|
|
phy-names = "usb3-phy";
|
|
phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
|
|
/delete-property/ reset-gpios;
|
|
};
|
|
|
|
&dwc3_0 {
|
|
status = "okay";
|
|
dr_mode = "peripheral";
|
|
maximum-speed = "super-speed";
|
|
};
|
|
|
|
/* ULPI SMSC USB3320 */
|
|
&usb1 {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usb1_default>;
|
|
phy-names = "usb3-phy";
|
|
phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
|
|
reset-gpios = <&modepin_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&dwc3_1 {
|
|
status = "okay";
|
|
dr_mode = "host";
|
|
maximum-speed = "super-speed";
|
|
};
|
|
|
|
&watchdog0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&xilinx_ams {
|
|
status = "okay";
|
|
};
|
|
|
|
&ams_ps {
|
|
status = "okay";
|
|
};
|
|
|
|
&zynqmp_dpdma {
|
|
status = "okay";
|
|
};
|
|
|
|
&zynqmp_dpsub {
|
|
status = "okay";
|
|
phy-names = "dp-phy0", "dp-phy1";
|
|
phys = <&psgtr 1 PHY_TYPE_DP 0 1>,
|
|
<&psgtr 0 PHY_TYPE_DP 1 1>;
|
|
};
|