mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
771635f6b0
Now that the zynqmp pinctrl driver supports the tri-state registers, make sure that the pins requiring output-enable are configured appropriately for SOMs. Without it, all tristate setting for MIOs, which are not related to SOM itself, are using default configuration which is not correct setting. It means SDs, USBs, ethernet, etc. are not working properly. In past it was fixed through calling tristate configuration via bootcmd: usb_init=mw 0xFF180208 2020 kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \ gpio toggle gpio@ff0a000038 Signed-off-by: Neal Frager <neal.frager@amd.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/7ecd98b2a302c5c6628e0234482f23c38e721fd6.1693492064.git.michal.simek@amd.com
351 lines
7.2 KiB
Text
351 lines
7.2 KiB
Text
// SPDX-License-Identifier: GPL-2.0
|
||
/*
|
||
* dts file for KV260 revA Carrier Card
|
||
*
|
||
* (C) Copyright 2020 - 2021, Xilinx, Inc.
|
||
*
|
||
* SD level shifter:
|
||
* "A" – A01 board un-modified (NXP)
|
||
* "Y" – A01 board modified with legacy interposer (Nexperia)
|
||
* "Z" – A01 board modified with Diode interposer
|
||
*
|
||
* Michal Simek <michal.simek@amd.com>
|
||
*/
|
||
|
||
#include <dt-bindings/gpio/gpio.h>
|
||
#include <dt-bindings/net/ti-dp83867.h>
|
||
#include <dt-bindings/phy/phy.h>
|
||
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
|
||
|
||
/dts-v1/;
|
||
/plugin/;
|
||
|
||
&{/} {
|
||
compatible = "xlnx,zynqmp-sk-kv260-revA",
|
||
"xlnx,zynqmp-sk-kv260-revY",
|
||
"xlnx,zynqmp-sk-kv260-revZ",
|
||
"xlnx,zynqmp-sk-kv260", "xlnx,zynqmp";
|
||
model = "ZynqMP KV260 revA";
|
||
};
|
||
|
||
&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
|
||
#address-cells = <1>;
|
||
#size-cells = <0>;
|
||
pinctrl-names = "default", "gpio";
|
||
pinctrl-0 = <&pinctrl_i2c1_default>;
|
||
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
||
scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||
|
||
u14: ina260@40 { /* u14 */
|
||
compatible = "ti,ina260";
|
||
#io-channel-cells = <1>;
|
||
label = "ina260-u14";
|
||
reg = <0x40>;
|
||
};
|
||
/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
|
||
};
|
||
|
||
&amba {
|
||
ina260-u14 {
|
||
compatible = "iio-hwmon";
|
||
io-channels = <&u14 0>, <&u14 1>, <&u14 2>;
|
||
};
|
||
|
||
si5332_0: si5332_0 { /* u17 */
|
||
compatible = "fixed-clock";
|
||
#clock-cells = <0>;
|
||
clock-frequency = <125000000>;
|
||
};
|
||
|
||
si5332_1: si5332_1 { /* u17 */
|
||
compatible = "fixed-clock";
|
||
#clock-cells = <0>;
|
||
clock-frequency = <25000000>;
|
||
};
|
||
|
||
si5332_2: si5332_2 { /* u17 */
|
||
compatible = "fixed-clock";
|
||
#clock-cells = <0>;
|
||
clock-frequency = <48000000>;
|
||
};
|
||
|
||
si5332_3: si5332_3 { /* u17 */
|
||
compatible = "fixed-clock";
|
||
#clock-cells = <0>;
|
||
clock-frequency = <24000000>;
|
||
};
|
||
|
||
si5332_4: si5332_4 { /* u17 */
|
||
compatible = "fixed-clock";
|
||
#clock-cells = <0>;
|
||
clock-frequency = <26000000>;
|
||
};
|
||
|
||
si5332_5: si5332_5 { /* u17 */
|
||
compatible = "fixed-clock";
|
||
#clock-cells = <0>;
|
||
clock-frequency = <27000000>;
|
||
};
|
||
};
|
||
|
||
/* DP/USB 3.0 and SATA */
|
||
&psgtr {
|
||
status = "okay";
|
||
/* pcie, usb3, sata */
|
||
clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
|
||
clock-names = "ref0", "ref1", "ref2";
|
||
};
|
||
|
||
&sata {
|
||
status = "okay";
|
||
/* SATA OOB timing settings */
|
||
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
|
||
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
|
||
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
|
||
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
|
||
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
|
||
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
|
||
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
|
||
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
|
||
phy-names = "sata-phy";
|
||
phys = <&psgtr 3 PHY_TYPE_SATA 1 2>;
|
||
};
|
||
|
||
&zynqmp_dpsub {
|
||
status = "okay";
|
||
phy-names = "dp-phy0", "dp-phy1";
|
||
phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
|
||
assigned-clock-rates = <27000000>, <25000000>, <300000000>;
|
||
};
|
||
|
||
&zynqmp_dpdma {
|
||
status = "okay";
|
||
assigned-clock-rates = <600000000>;
|
||
};
|
||
|
||
&usb0 {
|
||
status = "okay";
|
||
pinctrl-names = "default";
|
||
pinctrl-0 = <&pinctrl_usb0_default>;
|
||
phy-names = "usb3-phy";
|
||
phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
|
||
usbhub: usb5744 { /* u43 */
|
||
compatible = "microchip,usb5744";
|
||
reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
||
};
|
||
};
|
||
|
||
&dwc3_0 {
|
||
status = "okay";
|
||
dr_mode = "host";
|
||
snps,usb3_lpm_capable;
|
||
maximum-speed = "super-speed";
|
||
};
|
||
|
||
&sdhci1 { /* on CC with tuned parameters */
|
||
status = "okay";
|
||
pinctrl-names = "default";
|
||
pinctrl-0 = <&pinctrl_sdhci1_default>;
|
||
/*
|
||
* SD 3.0 requires level shifter and this property
|
||
* should be removed if the board has level shifter and
|
||
* need to work in UHS mode
|
||
*/
|
||
no-1-8-v;
|
||
disable-wp;
|
||
xlnx,mio-bank = <1>;
|
||
assigned-clock-rates = <187498123>;
|
||
bus-width = <8>;
|
||
};
|
||
|
||
&gem3 {
|
||
status = "okay";
|
||
pinctrl-names = "default";
|
||
pinctrl-0 = <&pinctrl_gem3_default>;
|
||
phy-handle = <&phy0>;
|
||
phy-mode = "rgmii-id";
|
||
assigned-clock-rates = <250000000>;
|
||
|
||
mdio: mdio {
|
||
#address-cells = <1>;
|
||
#size-cells = <0>;
|
||
|
||
phy0: ethernet-phy@1 {
|
||
#phy-cells = <1>;
|
||
reg = <1>;
|
||
compatible = "ethernet-phy-id2000.a231";
|
||
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
|
||
ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
|
||
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
|
||
ti,dp83867-rxctrl-strap-quirk;
|
||
reset-assert-us = <100>;
|
||
reset-deassert-us = <280>;
|
||
reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
||
};
|
||
};
|
||
};
|
||
|
||
&pinctrl0 {
|
||
status = "okay";
|
||
|
||
pinctrl_uart1_default: uart1-default {
|
||
conf {
|
||
groups = "uart1_9_grp";
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
drive-strength = <12>;
|
||
};
|
||
|
||
conf-rx {
|
||
pins = "MIO37";
|
||
bias-high-impedance;
|
||
};
|
||
|
||
conf-tx {
|
||
pins = "MIO36";
|
||
bias-disable;
|
||
output-enable;
|
||
};
|
||
|
||
mux {
|
||
groups = "uart1_9_grp";
|
||
function = "uart1";
|
||
};
|
||
};
|
||
|
||
pinctrl_i2c1_default: i2c1-default {
|
||
conf {
|
||
groups = "i2c1_6_grp";
|
||
bias-pull-up;
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
};
|
||
|
||
mux {
|
||
groups = "i2c1_6_grp";
|
||
function = "i2c1";
|
||
};
|
||
};
|
||
|
||
pinctrl_i2c1_gpio: i2c1-gpio {
|
||
conf {
|
||
groups = "gpio0_24_grp", "gpio0_25_grp";
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
};
|
||
|
||
mux {
|
||
groups = "gpio0_24_grp", "gpio0_25_grp";
|
||
function = "gpio0";
|
||
};
|
||
};
|
||
|
||
pinctrl_gem3_default: gem3-default {
|
||
conf {
|
||
groups = "ethernet3_0_grp";
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
};
|
||
|
||
conf-rx {
|
||
pins = "MIO70", "MIO72", "MIO74";
|
||
bias-high-impedance;
|
||
low-power-disable;
|
||
};
|
||
|
||
conf-bootstrap {
|
||
pins = "MIO71", "MIO73", "MIO75";
|
||
bias-disable;
|
||
output-enable;
|
||
low-power-disable;
|
||
};
|
||
|
||
conf-tx {
|
||
pins = "MIO64", "MIO65", "MIO66",
|
||
"MIO67", "MIO68", "MIO69";
|
||
bias-disable;
|
||
output-enable;
|
||
low-power-enable;
|
||
};
|
||
|
||
conf-mdio {
|
||
groups = "mdio3_0_grp";
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
bias-disable;
|
||
output-enable;
|
||
};
|
||
|
||
mux-mdio {
|
||
function = "mdio3";
|
||
groups = "mdio3_0_grp";
|
||
};
|
||
|
||
mux {
|
||
function = "ethernet3";
|
||
groups = "ethernet3_0_grp";
|
||
};
|
||
};
|
||
|
||
pinctrl_usb0_default: usb0-default {
|
||
conf {
|
||
groups = "usb0_0_grp";
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
};
|
||
|
||
conf-rx {
|
||
pins = "MIO52", "MIO53", "MIO55";
|
||
bias-high-impedance;
|
||
drive-strength = <12>;
|
||
slew-rate = <SLEW_RATE_FAST>;
|
||
};
|
||
|
||
conf-tx {
|
||
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
|
||
"MIO60", "MIO61", "MIO62", "MIO63";
|
||
bias-disable;
|
||
output-enable;
|
||
drive-strength = <4>;
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
};
|
||
|
||
mux {
|
||
groups = "usb0_0_grp";
|
||
function = "usb0";
|
||
};
|
||
};
|
||
|
||
pinctrl_sdhci1_default: sdhci1-default {
|
||
conf {
|
||
groups = "sdio1_0_grp";
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
bias-disable;
|
||
};
|
||
|
||
conf-cd {
|
||
groups = "sdio1_cd_0_grp";
|
||
bias-high-impedance;
|
||
bias-pull-up;
|
||
slew-rate = <SLEW_RATE_SLOW>;
|
||
power-source = <IO_STANDARD_LVCMOS18>;
|
||
};
|
||
|
||
mux-cd {
|
||
groups = "sdio1_cd_0_grp";
|
||
function = "sdio1_cd";
|
||
};
|
||
|
||
mux {
|
||
groups = "sdio1_0_grp";
|
||
function = "sdio1";
|
||
};
|
||
};
|
||
};
|
||
|
||
&uart1 {
|
||
status = "okay";
|
||
pinctrl-names = "default";
|
||
pinctrl-0 = <&pinctrl_uart1_default>;
|
||
};
|