mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
cfb7102d8d
Current CP1 pinctrl that is set on the Puzzle M801 is incorrect.
CP1 pins are only used for the SMI bus and the MSS I2C, all other
pins are just GPIO-s.
Due to this being set completely wrong, the pinctrl was actually
ended up being hardcoded in the board_early_init_f() step so that
SMI would work.
That is obviously not the right thing to do, so convert the register
hex values that were being written to individual pin modes and set it
in the DTS.
Add the SMI pins to the CP1 MDIO node as otherwise CP1 pinctrl does
not get probed without an consumer.
Fixes: 2ae2b8a2
("arm: mvebu: Initial iEi Puzzle-M801 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
383 lines
6.9 KiB
Text
383 lines
6.9 KiB
Text
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (C) 2016 Marvell International Ltd.
|
|
* Copyright (C) 2020 Sartura Ltd.
|
|
*/
|
|
|
|
#include "armada-8040.dtsi" /* include SoC device tree */
|
|
|
|
/ {
|
|
model = "iEi-Puzzle-M801";
|
|
compatible = "marvell,armada8040-puzzle-m801",
|
|
"marvell,armada8040";
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
aliases {
|
|
i2c0 = &ap_i2c0;
|
|
i2c1 = &cp0_i2c0;
|
|
i2c2 = &cp0_i2c1;
|
|
i2c3 = &i2c_switch;
|
|
spi0 = &ap_spi0;
|
|
gpio0 = &ap_gpio0;
|
|
gpio1 = &cp0_gpio0;
|
|
gpio2 = &cp0_gpio1;
|
|
gpio3 = &sfpplus_gpio;
|
|
};
|
|
|
|
memory@00000000 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x0 0x0 0x80000000>;
|
|
};
|
|
|
|
simple-bus {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
reg_usb3h0_vbus: usb3-vbus0 {
|
|
compatible = "regulator-fixed";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cp0_xhci_vbus_pins>;
|
|
regulator-name = "reg-usb3h0-vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
startup-delay-us = <500000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&cp0_gpio1 15 GPIO_ACTIVE_HIGH>; /* GPIO[47] */
|
|
};
|
|
};
|
|
};
|
|
|
|
&ap_i2c0 {
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
|
|
rtc@32 {
|
|
compatible = "epson,rx8010";
|
|
reg = <0x32>;
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ap_pinctl {
|
|
/*
|
|
* MPP Bus:
|
|
* AP SPI0 [0-3]
|
|
* AP I2C [4-5]
|
|
* AP GPIO [6]
|
|
* AP UART 1 RX/TX [7-8]
|
|
* AP GPIO [9-10]
|
|
* AP GPIO [12]
|
|
* UART0 [11,19]
|
|
*/
|
|
/* 0 1 2 3 4 5 6 7 8 9 */
|
|
pin-func = < 3 3 3 3 3 3 3 3 3 0
|
|
0 3 0 0 0 0 0 0 0 3 >;
|
|
};
|
|
|
|
&cp0_pinctl {
|
|
/*
|
|
* MPP Bus:
|
|
* [0-31] = 0xff: Keep default CP0_shared_pins:
|
|
* [11] CLKOUT_MPP_11 (out)
|
|
* [23] LINK_RD_IN_CP2CP (in)
|
|
* [25] CLKOUT_MPP_25 (out)
|
|
* [29] AVS_FB_IN_CP2CP (in)
|
|
* [32,34] SMI
|
|
* [33] MSS power down
|
|
* [35-38] CP0 I2C1 and I2C0
|
|
* [39] MSS CKE Enable
|
|
* [40,41] CP0 UART1 TX/RX
|
|
* [42,43] XSMI (controls two 10G phys)
|
|
* [47] USB VBUS EN
|
|
* [48] FAN PWM
|
|
* [49] 10G port 1 interrupt
|
|
* [50] 10G port 0 interrupt
|
|
* [51] 2.5G SFP TX fault
|
|
* [52] PCIe reset out
|
|
* [53] 2.5G SFP mode
|
|
* [54] 2.5G SFP LOS
|
|
* [55] Micro SD card detect
|
|
* [56-61] Micro SD
|
|
* [62] CP1 SFI SFP FAULT
|
|
*/
|
|
/* 0 1 2 3 4 5 6 7 8 9 */
|
|
pin-func = < 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
|
|
0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
|
|
0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
|
|
0xff 0 7 0xa 7 2 2 2 2 0xa
|
|
7 7 8 8 0 0 0 0 0 0
|
|
0 0 0 0 0 0 0xe 0xe 0xe 0xe
|
|
0xe 0xe 0 >;
|
|
|
|
cp0_xhci_vbus_pins: cpm-xhci-vbus-pins {
|
|
marvell,pins = < 47 >;
|
|
marvell,function = <0>;
|
|
};
|
|
|
|
cp0_pcie_reset_pins: cpm-pcie-reset-pins {
|
|
marvell,pins = < 52 >;
|
|
marvell,function = <0>;
|
|
};
|
|
};
|
|
|
|
&cp0_sdhci0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cp0_sdhci_pins>;
|
|
bus-width= <4>;
|
|
status = "okay";
|
|
};
|
|
|
|
&cp0_pcie0 {
|
|
num-lanes = <1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cp0_pcie_reset_pins>;
|
|
marvell,reset-gpio = <&cp0_gpio1 20 GPIO_ACTIVE_LOW>; /* GPIO[52] */
|
|
status = "okay";
|
|
};
|
|
|
|
&cp0_i2c0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cp0_i2c0_pins>;
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
|
|
sfpplus_gpio: gpio@21 {
|
|
compatible = "nxp,pca9555";
|
|
reg = <0x21>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
};
|
|
|
|
&cp0_i2c1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cp0_i2c1_pins>;
|
|
status = "okay";
|
|
clock-frequency = <100000>;
|
|
|
|
i2c_switch: i2c-switch@70 {
|
|
compatible = "nxp,pca9544";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x70>;
|
|
};
|
|
};
|
|
|
|
&cp0_sata0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&cp0_ethernet {
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&cp0_mdio {
|
|
status = "okay";
|
|
cp0_ge_phy0: ethernet-phy@1 {
|
|
reg = <0>;
|
|
};
|
|
|
|
cp0_ge_phy1: ethernet-phy@2 {
|
|
reg = <1>;
|
|
};
|
|
};
|
|
|
|
&cp0_eth0 {
|
|
status = "okay";
|
|
phy-mode = "sfi";
|
|
};
|
|
|
|
&cp0_eth1 {
|
|
status = "okay";
|
|
phy-mode = "sgmii";
|
|
phy = <&cp0_ge_phy0>;
|
|
};
|
|
|
|
&cp0_eth2 {
|
|
status = "okay";
|
|
phy-mode = "sgmii";
|
|
phy = <&cp0_ge_phy1>;
|
|
};
|
|
|
|
&cp0_comphy {
|
|
/*
|
|
* CP0 Serdes Configuration:
|
|
* Lane 0: PCIe0 (x1)
|
|
* Lane 1: SGMII2
|
|
* Lane 2: SATA0
|
|
* Lane 3: SGMII1
|
|
* Lane 4: SFI (10G)
|
|
* Lane 5: SATA1
|
|
*/
|
|
phy0 {
|
|
phy-type = <COMPHY_TYPE_PEX0>;
|
|
};
|
|
phy1 {
|
|
phy-type = <COMPHY_TYPE_SGMII2>;
|
|
phy-speed = <COMPHY_SPEED_1_25G>;
|
|
};
|
|
phy2 {
|
|
phy-type = <COMPHY_TYPE_SATA0>;
|
|
};
|
|
phy3 {
|
|
phy-type = <COMPHY_TYPE_SGMII1>;
|
|
phy-speed = <COMPHY_SPEED_1_25G>;
|
|
};
|
|
phy4 {
|
|
phy-type = <COMPHY_TYPE_SFI0>;
|
|
};
|
|
phy5 {
|
|
phy-type = <COMPHY_TYPE_SATA1>;
|
|
};
|
|
};
|
|
|
|
&cp1_mdio {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cp1_smi_pins>;
|
|
|
|
cp1_ge_phy0: ethernet-phy@3 {
|
|
reg = <1>;
|
|
};
|
|
|
|
cp1_ge_phy1: ethernet-phy@4 {
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
&cp1_pcie0 {
|
|
num-lanes = <2>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&cp1_usb3_0 {
|
|
vbus-supply = <®_usb3h0_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&cp1_utmi0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&cp1_ethernet {
|
|
status = "okay";
|
|
};
|
|
|
|
&cp1_eth0 {
|
|
status = "okay";
|
|
phy-mode = "sfi";
|
|
};
|
|
|
|
&cp1_eth1 {
|
|
status = "okay";
|
|
phy = <&cp1_ge_phy0>;
|
|
phy-mode = "sgmii";
|
|
};
|
|
|
|
&cp1_eth2 {
|
|
status = "okay";
|
|
phy = <&cp1_ge_phy1>;
|
|
phy-mode = "sgmii";
|
|
};
|
|
|
|
&cp1_pinctl {
|
|
/*
|
|
* MPP Bus:
|
|
* [0-5] TDM
|
|
* [27-28] SMI
|
|
* [29-30] CP1 MSS I2C
|
|
* [6-26, 31] GPIO
|
|
* [32-62] = 0xff: Keep default CP1_shared_pins:
|
|
*/
|
|
/* 0 1 2 3 4 5 6 7 8 9 */
|
|
pin-func = < 0x4 0x4 0x4 0x4 0x4 0x4 0x0 0x0 0x0 0x0
|
|
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
|
|
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x8 0x8 0x8
|
|
0x8 0x0 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
|
|
0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
|
|
0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
|
|
0xff 0xff 0xff>;
|
|
|
|
cp1_smi_pins: cp1-smi-pins {
|
|
marvell,pins = < 27 28 >;
|
|
marvell,function = <8>;
|
|
};
|
|
};
|
|
|
|
&ap_spi0 {
|
|
status = "okay";
|
|
|
|
spi-flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@u-boot {
|
|
reg = <0x00000000 0x001f0000>;
|
|
label = "u-boot";
|
|
};
|
|
partition@u-boot-env {
|
|
reg = <0x001f0000 0x00010000>;
|
|
label = "u-boot-env";
|
|
};
|
|
partition@ubi1 {
|
|
reg = <0x00200000 0x03f00000>;
|
|
label = "ubi1";
|
|
};
|
|
partition@ubi2 {
|
|
reg = <0x04100000 0x03f00000>;
|
|
label = "ubi2";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&cp1_comphy {
|
|
/*
|
|
* CP1 Serdes Configuration:
|
|
* Lane 0: PCIe0 (x2)
|
|
* Lane 1: PCIe0 (x2)
|
|
* Lane 2: USB HOST 0
|
|
* Lane 3: SGMII1
|
|
* Lane 4: SFI (10G)
|
|
* Lane 5: SGMII2
|
|
*/
|
|
phy0 {
|
|
phy-type = <COMPHY_TYPE_PEX0>;
|
|
};
|
|
phy1 {
|
|
phy-type = <COMPHY_TYPE_PEX0>;
|
|
};
|
|
phy2 {
|
|
phy-type = <COMPHY_TYPE_USB3_HOST0>;
|
|
};
|
|
phy3 {
|
|
phy-type = <COMPHY_TYPE_SGMII1>;
|
|
phy-speed = <COMPHY_SPEED_1_25G>;
|
|
};
|
|
phy4 {
|
|
phy-type = <COMPHY_TYPE_SFI0>;
|
|
};
|
|
phy5 {
|
|
phy-type = <COMPHY_TYPE_SGMII2>;
|
|
phy-speed = <COMPHY_SPEED_1_25G>;
|
|
};
|
|
};
|