mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-30 06:53:09 +00:00
8134853b93
The in-spl enabled DM serial console requires the board setup to be able to parse SPL_OF_PLATDATA based serial driver (pl01x) for the imx28 based XEA board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
225 lines
4.6 KiB
C
225 lines
4.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* XEA iMX28 board
|
|
*
|
|
* Copyright (C) 2019 DENX Software Engineering
|
|
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
|
|
*
|
|
* Copyright (C) 2018 DENX Software Engineering
|
|
* Måns Rullgård, DENX Software Engineering, mans@mansr.com
|
|
*
|
|
* Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
|
|
* on behalf of DENX Software Engineering GmbH
|
|
*
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <fdt_support.h>
|
|
#include <init.h>
|
|
#include <log.h>
|
|
#include <net.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/iomux-mx28.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/mii.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <errno.h>
|
|
#include <usb.h>
|
|
#include <serial.h>
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#include <spl.h>
|
|
#endif
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* Functions
|
|
*/
|
|
|
|
static void init_clocks(void)
|
|
{
|
|
/* IO0 clock at 480MHz */
|
|
mxs_set_ioclk(MXC_IOCLK0, 480000);
|
|
/* IO1 clock at 480MHz */
|
|
mxs_set_ioclk(MXC_IOCLK1, 480000);
|
|
|
|
/* SSP0 clock at 96MHz */
|
|
mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
|
|
/* SSP2 clock at 160MHz */
|
|
mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
|
|
/* SSP3 clock at 96MHz */
|
|
mxs_set_sspclk(MXC_SSPCLK3, 96000, 0);
|
|
}
|
|
|
|
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_FRAMEWORK)
|
|
void board_init_f(ulong arg)
|
|
{
|
|
init_clocks();
|
|
spl_early_init();
|
|
preloader_console_init();
|
|
}
|
|
|
|
static int boot_tiva0, boot_tiva1;
|
|
|
|
/* Check if TIVAs request booting via U-Boot proper */
|
|
void spl_board_init(void)
|
|
{
|
|
struct gpio_desc btiva0, btiva1, en_3_3v;
|
|
int ret;
|
|
|
|
/*
|
|
* Setup GPIO0_0 (TIVA power enable pin) to be output high
|
|
* to allow TIVA startup.
|
|
*/
|
|
ret = dm_gpio_lookup_name("GPIO0_0", &en_3_3v);
|
|
if (ret)
|
|
printf("Cannot get GPIO0_0\n");
|
|
|
|
ret = dm_gpio_request(&en_3_3v, "pwr_3_3v");
|
|
if (ret)
|
|
printf("Cannot request GPIO0_0\n");
|
|
|
|
/* Set GPIO0_0 to HIGH */
|
|
dm_gpio_set_dir_flags(&en_3_3v, GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
|
|
|
|
ret = dm_gpio_lookup_name("GPIO0_23", &btiva0);
|
|
if (ret)
|
|
printf("Cannot get GPIO0_23\n");
|
|
|
|
ret = dm_gpio_lookup_name("GPIO0_25", &btiva1);
|
|
if (ret)
|
|
printf("Cannot get GPIO0_25\n");
|
|
|
|
ret = dm_gpio_request(&btiva0, "boot-tiva0");
|
|
if (ret)
|
|
printf("Cannot request GPIO0_23\n");
|
|
|
|
ret = dm_gpio_request(&btiva1, "boot-tiva1");
|
|
if (ret)
|
|
printf("Cannot request GPIO0_25\n");
|
|
|
|
dm_gpio_set_dir_flags(&btiva0, GPIOD_IS_IN);
|
|
dm_gpio_set_dir_flags(&btiva1, GPIOD_IS_IN);
|
|
|
|
udelay(1000);
|
|
|
|
boot_tiva0 = dm_gpio_get_value(&btiva0);
|
|
boot_tiva1 = dm_gpio_get_value(&btiva1);
|
|
}
|
|
|
|
void board_boot_order(u32 *spl_boot_list)
|
|
{
|
|
spl_boot_list[0] = BOOT_DEVICE_MMC1;
|
|
spl_boot_list[1] = BOOT_DEVICE_SPI;
|
|
spl_boot_list[2] = BOOT_DEVICE_UART;
|
|
}
|
|
|
|
int spl_start_uboot(void)
|
|
{
|
|
/* break into full u-boot on 'c' */
|
|
if (serial_tstc() && serial_getc() == 'c')
|
|
return 1;
|
|
|
|
debug("%s: btiva0: %d btiva1: %d\n", __func__, boot_tiva0, boot_tiva1);
|
|
return !boot_tiva0 || !boot_tiva1;
|
|
}
|
|
#else
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
init_clocks();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
struct gpio_desc phy_rst;
|
|
int ret;
|
|
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
|
|
|
|
cpu_eth_init(NULL);
|
|
|
|
/* PHY INT#/PWDN# */
|
|
ret = dm_gpio_lookup_name("GPIO4_13", &phy_rst);
|
|
if (ret) {
|
|
printf("Cannot get GPIO4_13\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = dm_gpio_request(&phy_rst, "phy-rst");
|
|
if (ret) {
|
|
printf("Cannot request GPIO4_13\n");
|
|
return ret;
|
|
}
|
|
|
|
dm_gpio_set_dir_flags(&phy_rst, GPIOD_IS_IN);
|
|
udelay(1000);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
return mxs_dram_init();
|
|
}
|
|
|
|
#ifdef CONFIG_OF_BOARD_SETUP
|
|
static int fdt_fixup_l2switch(void *blob)
|
|
{
|
|
u8 ethaddr[6];
|
|
int ret;
|
|
|
|
if (eth_env_get_enetaddr("ethaddr", ethaddr)) {
|
|
ret = fdt_find_and_setprop(blob,
|
|
"/ahb@80080000/switch@800f0000",
|
|
"local-mac-address", ethaddr, 6, 1);
|
|
if (ret < 0)
|
|
printf("%s: can't find usbether@1 node: %d\n",
|
|
__func__, ret);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int ft_board_setup(void *blob, struct bd_info *bd)
|
|
{
|
|
/*
|
|
* i.MX28 L2 switch needs manual update (fixup) of eth MAC address
|
|
* (in 'local-mac-address' property) as it uses "switch@800f0000"
|
|
* node, not set by default FIT image handling code in
|
|
* "ethernet@800f0000"
|
|
*/
|
|
fdt_fixup_l2switch(blob);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
/*
|
|
* NOTE:
|
|
*
|
|
* IMX28 clock "stub" DM driver!
|
|
*
|
|
* Only used for SPL stage, which is NOT using DM; serial and
|
|
* eMMC configuration.
|
|
*/
|
|
static const struct udevice_id imx28_clk_ids[] = {
|
|
{ .compatible = "fsl,imx28-clkctrl", },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(fsl_imx28_clkctrl) = {
|
|
.name = "fsl_imx28_clkctrl",
|
|
.id = UCLASS_CLK,
|
|
.of_match = imx28_clk_ids,
|
|
};
|
|
#endif /* CONFIG_SPL_BUILD */
|