mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-30 06:53:09 +00:00
f0f461287e
As explained in the text at the bottom of the page https://source.codeaurora.org/external/imx/imx-atf: "QUIC repositories on this site will not receive any updates after March 31, 2022, and will be deleted on March 31, 2023." Point to the NXP ATF github repo instead. Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
89 lines
1.9 KiB
ReStructuredText
89 lines
1.9 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
imx8mm_evk
|
|
==========
|
|
|
|
U-Boot for the NXP i.MX8MM EVK board
|
|
|
|
Quick Start
|
|
-----------
|
|
|
|
- Build the ARM Trusted firmware binary
|
|
- Get ddr firmware
|
|
- Build U-Boot
|
|
- Boot
|
|
|
|
Get and Build the ARM Trusted firmware
|
|
--------------------------------------
|
|
|
|
Note: builddir is U-Boot build directory (source directory for in-tree builds)
|
|
Get ATF from: https://github.com/nxp-imx/imx-atf
|
|
branch: imx_5.4.47_2.2.0
|
|
|
|
.. code-block:: bash
|
|
|
|
$ make PLAT=imx8mm bl31
|
|
$ cp build/imx8mm/release/bl31.bin $(builddir)
|
|
|
|
Get the ddr firmware
|
|
--------------------
|
|
|
|
.. code-block:: bash
|
|
|
|
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
|
|
$ chmod +x firmware-imx-8.9.bin
|
|
$ ./firmware-imx-8.9
|
|
$ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
|
|
|
|
Build U-Boot for sd card
|
|
--------------------------
|
|
|
|
.. code-block:: bash
|
|
|
|
$ export CROSS_COMPILE=aarch64-poky-linux-
|
|
$ make imx8mm_evk_defconfig
|
|
$ make
|
|
|
|
Burn the flash.bin to MicroSD card offset 33KB:
|
|
|
|
.. code-block:: bash
|
|
|
|
$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 conv=notrunc
|
|
|
|
Boot
|
|
----
|
|
Set Boot switch to SD boot
|
|
|
|
Build U-Boot for qspi flash card
|
|
------------------------------------
|
|
|
|
.. code-block:: bash
|
|
|
|
$ export CROSS_COMPILE=aarch64-poky-linux-
|
|
$ make imx8mm_evk_fspi_defconfig
|
|
$ make
|
|
|
|
Currently, there is no direct support to write to QSPI Flash.
|
|
Copy flash.bin to ${loadaddr} either from sd card or over network and then copy to
|
|
qspi flash
|
|
|
|
From sd card to memory
|
|
|
|
.. code-block:: bash
|
|
|
|
$mmc dev 1
|
|
$mmc read ${loadaddr} 0x00 <size_of_flash.bin/512>
|
|
|
|
.. code-block:: bash
|
|
|
|
$ sf probe
|
|
$ sf erase 0 <size_of_flash.bin_in_hex>
|
|
$ sf write $loadaddr 0x00 <size_of_flash.bin_in_hex>
|
|
|
|
Boot from QSPI Flash
|
|
-----------------------
|
|
Set Boot Switch to QSPI Flash
|
|
|
|
Pin configuration for imx8mm_revC evk to boot from qspi flash
|
|
SW1101: 0110xxxxxx
|
|
SW1102: 00100x0010
|