u-boot/include/configs/MPC8315ERDB.h
Adam Ford e91907a146 Convert CONFIG_ENV_OVERWRITE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 16:18:06 -04:00

370 lines
11 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
*
* Dave Liu <daveliu@freescale.com>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH 0x00000000
#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
#define CONFIG_HWCONFIG
/*
* DDR Setup
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
| DDRCDR_PZ_LOZ \
| DDRCDR_NZ_LOZ \
| DDRCDR_ODT \
| DDRCDR_Q_DRN)
/* 0x7b880001 */
/*
* Manually set up DDR parameters
* consist of two chips HY5PS12621BFP-C4 from HYNIX
*/
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
| CSCONFIG_ODT_RD_NEVER \
| CSCONFIG_ODT_WR_ONLY_CURRENT \
| CSCONFIG_ROW_BIT_13 \
| CSCONFIG_COL_BIT_10)
/* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
| (0 << TIMING_CFG0_WRT_SHIFT) \
| (0 << TIMING_CFG0_RRT_SHIFT) \
| (0 << TIMING_CFG0_WWT_SHIFT) \
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
| (6 << TIMING_CFG1_REFREC_SHIFT) \
| (2 << TIMING_CFG1_WRREC_SHIFT) \
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
| (2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x27256222 */
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
| (4 << TIMING_CFG2_CPO_SHIFT) \
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
/* 0x121048c5 */
#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x03600100 */
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_DBW_32)
/* 0x43080000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
| (0x0232 << SDRAM_MODE_SD_SHIFT))
/* ODT 150ohm CL=3, AL=1 on SDRAM */
#define CONFIG_SYS_DDR_MODE2 0x00000000
/*
* Memory test
*/
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
/* 127 64KB sectors and 8 8KB top sectors per device */
#define CONFIG_SYS_MAX_FLASH_SECT 135
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* NAND Flash on the Local Bus
*/
#ifdef CONFIG_NAND_SPL
#define CONFIG_SYS_NAND_BASE 0xFFF00000
#else
#define CONFIG_SYS_NAND_BASE 0xE0600000
#endif
#define CONFIG_MTD_PARTITION
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
/* Still needed for spl_minimal.c */
#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
!defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
/*
* Serial Port
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
/*
* Board info - revision and where boot from
*/
#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
/*
* Config on-board RTC
*/
#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_SCCR_USBDRCM 3
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_PHY_TYPE "utmi"
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* TSEC
*/
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
/*
* TSEC ethernet configuration
*/
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME "eTSEC1"
/*
* SATA
*/
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1_OFFSET 0x18000
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2_OFFSET 0x19000
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#ifdef CONFIG_FSL_SATA
#define CONFIG_LBA48
#endif
/*
* Environment
*/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/*
* MMU Setup
*/
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#endif
/*
* Environment Configuration
*/
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
"fdtaddr=780000\0" \
"fdtfile=mpc8315erdb.dtb\0" \
"usb_phy_type=utmi\0" \
""
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
"$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */