mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-05 20:54:31 +00:00
f9a9fc6f53
To help others with compiling and flashing ATF and u-boot add a README for this board. Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
160 lines
5.3 KiB
Text
160 lines
5.3 KiB
Text
Introduction
|
|
============
|
|
|
|
HiKey is the first certified 96Boards Consumer Edition board. The board/SoC has: -
|
|
* HiSilicon Kirin 6220 eight-core ARM Cortex-A53 64-bit SoC running at 1.2GHz.
|
|
* ARM Mali 450-MP4 GPU
|
|
* 1GB 800MHz LPDDR3 DRAM
|
|
* 4GB eMMC Flash Storage
|
|
* microSD
|
|
* 802.11a/b/g/n WiFi, Bluetooth
|
|
|
|
The HiKey schematic can be found here: -
|
|
https://github.com/96boards/documentation/blob/master/hikey/96Boards-Hikey-Rev-A1.pdf
|
|
|
|
A SoC datasheet can be found here: -
|
|
https://github.com/96boards/documentation/blob/master/hikey/
|
|
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
|
|
|
|
Currently the u-boot port supports: -
|
|
* USB
|
|
* eMMC
|
|
* SD card
|
|
* GPIO
|
|
|
|
Compile u-boot
|
|
==============
|
|
|
|
make CROSS_COMPILE=aarch64-linux-gnu- hikey_config
|
|
make CROSS_COMPILE=aarch64-linux-gnu-
|
|
|
|
ARM Trusted Firmware (ATF) & l-loader
|
|
=====================================
|
|
|
|
This u-boot port has been tested with l-loader, booting ATF, which then boots
|
|
u-boot as the bl33.bin executable.
|
|
|
|
1. Get ATF source code
|
|
git clone https://github.com/96boards/arm-trusted-firmware.git
|
|
|
|
2. Compile ATF I use the makefile here
|
|
http://people.linaro.org/~peter.griffin/hikey/hikey-u-boot-release_r1/build-tf.mak
|
|
|
|
3. Get l-loader
|
|
git clone https://github.com/96boards/l-loader.git
|
|
|
|
4. Make sym links to ATF bip / fip binaries
|
|
ln -s /home/griffinp/aarch64/bl1-hikey.bin bl1.bin
|
|
ln -s /home/griffinp/aarch64/fip-hikey.bin fip.bin
|
|
|
|
arm-linux-gnueabihf-gcc -c -o start.o start.S
|
|
arm-linux-gnueabihf-gcc -c -o debug.o debug.S
|
|
arm-linux-gnueabihf-ld -Bstatic -Tl-loader.lds -Ttext 0xf9800800 start.o debug.o -o loader
|
|
arm-linux-gnueabihf-objcopy -O binary loader temp
|
|
|
|
python gen_loader.py -o l-loader.bin --img_loader=temp --img_bl1=bl1.bin
|
|
sudo bash -x generate_ptable.sh
|
|
python gen_loader.py -o ptable.img --img_prm_ptable=prm_ptable.img --img_sec_ptable=sec_ptable.img
|
|
|
|
These instructions are adapted from
|
|
https://github.com/96boards/documentation/wiki/HiKeyUEFI
|
|
|
|
FLASHING
|
|
========
|
|
|
|
1. Connect jumper J2 to go into recovery mode and flash l-loader.bin with
|
|
fastboot using the hisi-idt.py utility
|
|
|
|
> git clone https://github.com/96boards/burn-boot.git
|
|
> sudo python /home/griffinp/Software/hikey/burn-boot/hisi-idt.py -d /dev/ttyUSB0 --img1=/tmp/l-loader.bin
|
|
|
|
2. Once LED 0 comes on solid, it should be detected as a fastboot device
|
|
(on some boards I've found this to be unreliable)
|
|
|
|
sudo fastboot devices
|
|
|
|
3. Flash the images
|
|
wget https://builds.96boards.org/releases/hikey/nvme.img
|
|
sudo fastboot flash ptable ptable.img
|
|
sudo fastboot flash fastboot fip.bin
|
|
sudo fastboot flash nvme nvme.img
|
|
|
|
4. Disconnect jumper J2, and reset the board and you will now (hopefully)
|
|
have ATF, booting u-boot from eMMC. On 'new' boards I've had to do the
|
|
flashing twice in the past to avoid an ATF error.
|
|
|
|
See working boot trace below: -
|
|
|
|
debug EMMC boot: print init OK
|
|
debug EMMC boot: send RST_N .
|
|
debug EMMC boot: start eMMC boot......
|
|
load fastboot1!
|
|
Switch to aarch64 mode. CPU0 executes at 0xf9801000!
|
|
NOTICE: Booting Trusted Firmware
|
|
NOTICE: BL1: v1.1(release):a0c0399
|
|
NOTICE: BL1: Built : 13:23:48, May 22 2015
|
|
NOTICE: succeed to init lpddr3 rank0 dram phy
|
|
INFO: lpddr3_freq_init, set ddrc 533mhz
|
|
INFO: init ddr3 rank0
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: lpddr3_freq_init, set ddrc 800mhz
|
|
INFO: init ddr3 rank0
|
|
INFO: ddr3 rank1 init pass
|
|
INFO: Elpida DDR
|
|
NOTICE: BL1: Booting BL2
|
|
INFO: [BDID] [fff91c18] midr: 0x410fd033
|
|
INFO: [BDID] [fff91c1c] board type: 0
|
|
INFO: [BDID] [fff91c20] board id: 0x2b
|
|
INFO: init_acpu_dvfs: pmic version 17
|
|
INFO: init_acpu_dvfs: ACPU_CHIP_MAX_FREQ=0x186a00.
|
|
INFO: acpu_dvfs_volt_init: success!
|
|
INFO: acpu_dvfs_set_freq: support freq num is 5
|
|
INFO: acpu_dvfs_set_freq: start prof is 0x4
|
|
INFO: acpu_dvfs_set_freq: magic is 0x5a5ac5c5
|
|
INFO: acpu_dvfs_set_freq: voltage:
|
|
INFO: - 0: 0x3a
|
|
INFO: - 1: 0x3a
|
|
INFO: - 2: 0x4a
|
|
INFO: - 3: 0x5b
|
|
INFO: - 4: 0x6b
|
|
NOTICE: acpu_dvfs_set_freq: set acpu freq success!NOTICE: BL2: v1.1(debug):a0c0399
|
|
NOTICE: BL2: Built : 10:19:28, May 27 2015
|
|
INFO: BL2: Loading BL3-0
|
|
INFO: Using FIP
|
|
WARNING: Failed to access image 'bl30.bin' (-1)
|
|
ERROR: Failed to load BL3-0 (-1)
|
|
ERROR: Please burn mcu image:
|
|
ERROR: sudo fastboot flash mcuimage mcuimage.bin
|
|
INFO: BL2: TrustZone: protecting 16777216 bytes of memory at 0x3f000000
|
|
INFO: BL2: Loading BL3-1
|
|
INFO: Using FIP
|
|
INFO: Loading file 'bl31.bin' at address 0xf9858000
|
|
INFO: File 'bl31.bin' loaded: 0xf9858000 - 0xf9860010
|
|
INFO: BL2: Loading BL3-2
|
|
INFO: Using FIP
|
|
WARNING: Failed to access image 'bl32.bin' (-1)
|
|
WARNING: Failed to load BL3-2 (-1)
|
|
INFO: BL2: Loading BL3-3
|
|
INFO: Using FIP
|
|
INFO: Loading file 'bl33.bin' at address 0x35000000
|
|
INFO: File 'bl33.bin' loaded: 0x35000000 - 0x35042938
|
|
NOTICE: BL1: Booting BL3-1
|
|
NOTICE: BL3-1: v1.1(debug):a0c0399
|
|
NOTICE: BL3-1: Built : 10:19:31, May 27 2015
|
|
INFO: BL3-1: Initializing runtime services
|
|
INFO: BL3-1: Preparing for EL3 exit to normal world
|
|
INFO: BL3-1: Next image address = 0x35000000
|
|
INFO: BL3-1: Next image spsr = 0x3c9
|
|
|
|
|
|
U-Boot 2015.04-00007-g1b3d379-dirty (May 27 2015 - 10:18:16) hikey
|
|
|
|
DRAM: 1008 MiB
|
|
MMC: sd_card_detect: SD card present
|
|
HiKey DWMMC: 0, HiKey DWMMC: 1
|
|
In: serial
|
|
Out: serial
|
|
Err: serial
|
|
Net: Net Initialization Skipped
|
|
No ethernet found.
|
|
Hit any key to stop autoboot: 0
|