u-boot/drivers/fpga/virtex2.c
Peter Tyser 6385b28116 fpga: Remove relocation fixups
PPC boards are the only users of the current FPGA code which is littered
with manual relocation fixups.  Now that proper relocation is supported
for PPC boards, remove FPGA manual relocation.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-10-03 10:17:56 +02:00

436 lines
12 KiB
C

/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
*/
/*
* Configuration support for Xilinx Virtex2 devices. Based
* on spartan2.c (Rich Ireland, rireland@enterasys.com).
*/
#include <common.h>
#include <virtex2.h>
#if 0
#define FPGA_DEBUG
#endif
#ifdef FPGA_DEBUG
#define PRINTF(fmt,args...) printf (fmt ,##args)
#else
#define PRINTF(fmt,args...)
#endif
/*
* If the SelectMap interface can be overrun by the processor, define
* CONFIG_SYS_FPGA_CHECK_BUSY and/or CONFIG_FPGA_DELAY in the board configuration
* file and add board-specific support for checking BUSY status. By default,
* assume that the SelectMap interface cannot be overrun.
*/
#ifndef CONFIG_SYS_FPGA_CHECK_BUSY
#undef CONFIG_SYS_FPGA_CHECK_BUSY
#endif
#ifndef CONFIG_FPGA_DELAY
#define CONFIG_FPGA_DELAY()
#endif
#ifndef CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_SYS_FPGA_PROG_FEEDBACK
#endif
/*
* Don't allow config cycle to be interrupted
*/
#ifndef CONFIG_SYS_FPGA_CHECK_CTRLC
#undef CONFIG_SYS_FPGA_CHECK_CTRLC
#endif
/*
* Check for errors during configuration by default
*/
#ifndef CONFIG_SYS_FPGA_CHECK_ERROR
#define CONFIG_SYS_FPGA_CHECK_ERROR
#endif
/*
* The default timeout in mS for INIT_B to deassert after PROG_B has
* been deasserted. Per the latest Virtex II Handbook (page 347), the
* max time from PORG_B deassertion to INIT_B deassertion is 4uS per
* data frame for the XC2V8000. The XC2V8000 has 2860 data frames
* which yields 11.44 mS. So let's make it bigger in order to handle
* an XC2V1000, if anyone can ever get ahold of one.
*/
#ifndef CONFIG_SYS_FPGA_WAIT_INIT
#define CONFIG_SYS_FPGA_WAIT_INIT CONFIG_SYS_HZ/2 /* 500 ms */
#endif
/*
* The default timeout for waiting for BUSY to deassert during configuration.
* This is normally not necessary since for most reasonable configuration
* clock frequencies (i.e. 66 MHz or less), BUSY monitoring is unnecessary.
*/
#ifndef CONFIG_SYS_FPGA_WAIT_BUSY
#define CONFIG_SYS_FPGA_WAIT_BUSY CONFIG_SYS_HZ/200 /* 5 ms*/
#endif
/* Default timeout for waiting for FPGA to enter operational mode after
* configuration data has been written.
*/
#ifndef CONFIG_SYS_FPGA_WAIT_CONFIG
#define CONFIG_SYS_FPGA_WAIT_CONFIG CONFIG_SYS_HZ/5 /* 200 ms */
#endif
static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize);
static int Virtex2_ssm_dump (Xilinx_desc * desc, void *buf, size_t bsize);
static int Virtex2_ss_load (Xilinx_desc * desc, void *buf, size_t bsize);
static int Virtex2_ss_dump (Xilinx_desc * desc, void *buf, size_t bsize);
int Virtex2_load (Xilinx_desc * desc, void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Load\n", __FUNCTION__);
ret_val = Virtex2_ss_load (desc, buf, bsize);
break;
case slave_selectmap:
PRINTF ("%s: Launching Slave Parallel Load\n", __FUNCTION__);
ret_val = Virtex2_ssm_load (desc, buf, bsize);
break;
default:
printf ("%s: Unsupported interface type, %d\n",
__FUNCTION__, desc->iface);
}
return ret_val;
}
int Virtex2_dump (Xilinx_desc * desc, void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
switch (desc->iface) {
case slave_serial:
PRINTF ("%s: Launching Slave Serial Dump\n", __FUNCTION__);
ret_val = Virtex2_ss_dump (desc, buf, bsize);
break;
case slave_parallel:
PRINTF ("%s: Launching Slave Parallel Dump\n", __FUNCTION__);
ret_val = Virtex2_ssm_dump (desc, buf, bsize);
break;
default:
printf ("%s: Unsupported interface type, %d\n",
__FUNCTION__, desc->iface);
}
return ret_val;
}
int Virtex2_info (Xilinx_desc * desc)
{
return FPGA_SUCCESS;
}
/*
* Virtex-II Slave SelectMap configuration loader. Configuration via
* SelectMap is as follows:
* 1. Set the FPGA's PROG_B line low.
* 2. Set the FPGA's PROG_B line high. Wait for INIT_B to go high.
* 3. Write data to the SelectMap port. If INIT_B goes low at any time
* this process, a configuration error (most likely CRC failure) has
* ocurred. At this point a status word may be read from the
* SelectMap interface to determine the source of the problem (You
* could, for instance, put this in your 'abort' function handler).
* 4. After all data has been written, test the state of the FPGA
* INIT_B and DONE lines. If both are high, configuration has
* succeeded. Congratulations!
*/
static int Virtex2_ssm_load (Xilinx_desc * desc, void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
Xilinx_Virtex2_Slave_SelectMap_fns *fn = desc->iface_fns;
PRINTF ("%s:%d: Start with interface functions @ 0x%p\n",
__FUNCTION__, __LINE__, fn);
if (fn) {
size_t bytecount = 0;
unsigned char *data = (unsigned char *) buf;
int cookie = desc->cookie;
unsigned long ts;
/* Gotta split this one up (so the stack won't blow??) */
PRINTF ("%s:%d: Function Table:\n"
" base 0x%p\n"
" struct 0x%p\n"
" pre 0x%p\n"
" prog 0x%p\n"
" init 0x%p\n"
" error 0x%p\n",
__FUNCTION__, __LINE__,
&fn, fn, fn->pre, fn->pgm, fn->init, fn->err);
PRINTF (" clock 0x%p\n"
" cs 0x%p\n"
" write 0x%p\n"
" rdata 0x%p\n"
" wdata 0x%p\n"
" busy 0x%p\n"
" abort 0x%p\n"
" post 0x%p\n\n",
fn->clk, fn->cs, fn->wr, fn->rdata, fn->wdata,
fn->busy, fn->abort, fn->post);
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
printf ("Initializing FPGA Device %d...\n", cookie);
#endif
/*
* Run the pre configuration function if there is one.
*/
if (*fn->pre) {
(*fn->pre) (cookie);
}
/*
* Assert the program line. The minimum pulse width for
* Virtex II devices is 300 nS (Tprogram parameter in datasheet).
* There is no maximum value for the pulse width. Check to make
* sure that INIT_B goes low after assertion of PROG_B
*/
(*fn->pgm) (TRUE, TRUE, cookie);
udelay (10);
ts = get_timer (0);
do {
if (get_timer (ts) > CONFIG_SYS_FPGA_WAIT_INIT) {
printf ("%s:%d: ** Timeout after %d ticks waiting for INIT"
" to assert.\n", __FUNCTION__, __LINE__,
CONFIG_SYS_FPGA_WAIT_INIT);
(*fn->abort) (cookie);
return FPGA_FAIL;
}
} while (!(*fn->init) (cookie));
(*fn->pgm) (FALSE, TRUE, cookie);
CONFIG_FPGA_DELAY ();
(*fn->clk) (TRUE, TRUE, cookie);
/*
* Start a timer and wait for INIT_B to go high
*/
ts = get_timer (0);
do {
CONFIG_FPGA_DELAY ();
if (get_timer (ts) > CONFIG_SYS_FPGA_WAIT_INIT) {
printf ("%s:%d: ** Timeout after %d ticks waiting for INIT"
" to deassert.\n", __FUNCTION__, __LINE__,
CONFIG_SYS_FPGA_WAIT_INIT);
(*fn->abort) (cookie);
return FPGA_FAIL;
}
} while ((*fn->init) (cookie) && (*fn->busy) (cookie));
(*fn->wr) (TRUE, TRUE, cookie);
(*fn->cs) (TRUE, TRUE, cookie);
udelay (10000);
/*
* Load the data byte by byte
*/
while (bytecount < bsize) {
#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC
if (ctrlc ()) {
(*fn->abort) (cookie);
return FPGA_FAIL;
}
#endif
if ((*fn->done) (cookie) == FPGA_SUCCESS) {
PRINTF ("%s:%d:done went active early, bytecount = %d\n",
__FUNCTION__, __LINE__, bytecount);
break;
}
#ifdef CONFIG_SYS_FPGA_CHECK_ERROR
if ((*fn->init) (cookie)) {
printf ("\n%s:%d: ** Error: INIT asserted during"
" configuration\n", __FUNCTION__, __LINE__);
printf ("%d = buffer offset, %d = buffer size\n",
bytecount, bsize);
(*fn->abort) (cookie);
return FPGA_FAIL;
}
#endif
(*fn->wdata) (data[bytecount++], TRUE, cookie);
CONFIG_FPGA_DELAY ();
/*
* Cycle the clock pin
*/
(*fn->clk) (FALSE, TRUE, cookie);
CONFIG_FPGA_DELAY ();
(*fn->clk) (TRUE, TRUE, cookie);
#ifdef CONFIG_SYS_FPGA_CHECK_BUSY
ts = get_timer (0);
while ((*fn->busy) (cookie)) {
if (get_timer (ts) > CONFIG_SYS_FPGA_WAIT_BUSY) {
printf ("%s:%d: ** Timeout after %d ticks waiting for"
" BUSY to deassert\n",
__FUNCTION__, __LINE__, CONFIG_SYS_FPGA_WAIT_BUSY);
(*fn->abort) (cookie);
return FPGA_FAIL;
}
}
#endif
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
if (bytecount % (bsize / 40) == 0)
putc ('.');
#endif
}
/*
* Finished writing the data; deassert FPGA CS_B and WRITE_B signals.
*/
CONFIG_FPGA_DELAY ();
(*fn->cs) (FALSE, TRUE, cookie);
(*fn->wr) (FALSE, TRUE, cookie);
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
putc ('\n');
#endif
/*
* Check for successful configuration. FPGA INIT_B and DONE should
* both be high upon successful configuration.
*/
ts = get_timer (0);
ret_val = FPGA_SUCCESS;
while (((*fn->done) (cookie) == FPGA_FAIL) || (*fn->init) (cookie)) {
if (get_timer (ts) > CONFIG_SYS_FPGA_WAIT_CONFIG) {
printf ("%s:%d: ** Timeout after %d ticks waiting for DONE to"
"assert and INIT to deassert\n",
__FUNCTION__, __LINE__, CONFIG_SYS_FPGA_WAIT_CONFIG);
(*fn->abort) (cookie);
ret_val = FPGA_FAIL;
break;
}
}
if (ret_val == FPGA_SUCCESS) {
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
printf ("Initialization of FPGA device %d complete\n", cookie);
#endif
/*
* Run the post configuration function if there is one.
*/
if (*fn->post) {
(*fn->post) (cookie);
}
} else {
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
printf ("** Initialization of FPGA device %d FAILED\n",
cookie);
#endif
}
} else {
printf ("%s:%d: NULL Interface function table!\n",
__FUNCTION__, __LINE__);
}
return ret_val;
}
/*
* Read the FPGA configuration data
*/
static int Virtex2_ssm_dump (Xilinx_desc * desc, void *buf, size_t bsize)
{
int ret_val = FPGA_FAIL;
Xilinx_Virtex2_Slave_SelectMap_fns *fn = desc->iface_fns;
if (fn) {
unsigned char *data = (unsigned char *) buf;
size_t bytecount = 0;
int cookie = desc->cookie;
printf ("Starting Dump of FPGA Device %d...\n", cookie);
(*fn->cs) (TRUE, TRUE, cookie);
(*fn->clk) (TRUE, TRUE, cookie);
while (bytecount < bsize) {
#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC
if (ctrlc ()) {
(*fn->abort) (cookie);
return FPGA_FAIL;
}
#endif
/*
* Cycle the clock and read the data
*/
(*fn->clk) (FALSE, TRUE, cookie);
(*fn->clk) (TRUE, TRUE, cookie);
(*fn->rdata) (&(data[bytecount++]), cookie);
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
if (bytecount % (bsize / 40) == 0)
putc ('.');
#endif
}
/*
* Deassert CS_B and cycle the clock to deselect the device.
*/
(*fn->cs) (FALSE, FALSE, cookie);
(*fn->clk) (FALSE, TRUE, cookie);
(*fn->clk) (TRUE, TRUE, cookie);
#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK
putc ('\n');
#endif
puts ("Done.\n");
} else {
printf ("%s:%d: NULL Interface function table!\n",
__FUNCTION__, __LINE__);
}
return ret_val;
}
static int Virtex2_ss_load (Xilinx_desc * desc, void *buf, size_t bsize)
{
printf ("%s: Slave Serial Loading is unsupported\n", __FUNCTION__);
return FPGA_FAIL;
}
static int Virtex2_ss_dump (Xilinx_desc * desc, void *buf, size_t bsize)
{
printf ("%s: Slave Serial Dumping is unsupported\n", __FUNCTION__);
return FPGA_FAIL;
}
/* vim: set ts=4 tw=78: */