u-boot/include/configs/phycore_imx8mm.h
Tom Rini 9b5f9aeb3b Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BSS_MAX_SIZE
   CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:10 -04:00

87 lines
2.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0-or-later
*
* Copyright (C) 2019-2020 PHYTEC Messtechnik GmbH
* Author: Teresa Remmet <t.remmet@phytec.de>
*/
#ifndef __PHYCORE_IMX8MM_H
#define __PHYCORE_IMX8MM_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_BOOTM_LEN SZ_64M
#define CONFIG_SYS_MONITOR_LEN SZ_512K
#define CONFIG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK 0x920000
#define CONFIG_SPL_BSS_START_ADDR 0x910000
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR 0x930000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"image=Image\0" \
"console=ttymxc2,115200\0" \
"fdt_addr=0x48000000\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"ip_dyn=yes\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"mmcpart=1\0" \
"mmcroot=2\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console} " \
"root=/dev/mmcblk${mmcdev}p${mmcroot} rootwait rw\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if run loadfdt; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi;\0 " \
"nfsroot=/nfs\0" \
"netargs=setenv bootargs console=${console} root=/dev/nfs ip=dhcp " \
"nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${loadaddr} ${image}; " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi;\0" \
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE SZ_512K
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE SZ_2G /* 2GB DDR */
/* UART */
#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(3)
#endif /* __PHYCORE_IMX8MM_H */