u-boot/arch/powerpc/cpu/mpc8xx/scc.c
Wolfgang Denk 1b0757eced PPC: remove dead boards (AMX860, c2mon, ETX094, IAD210, LANTEC, SCM)
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years.  Get rid of the dead
weight.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
2012-10-28 20:17:25 +01:00

558 lines
15 KiB
C

/*
* File: scc.c
* Description:
* Basic ET HW initialization and packet RX/TX routines
*
* NOTE <<<IMPORTANT: PLEASE READ>>>:
* Do not cache Rx/Tx buffers!
*/
/*
* MPC823 <-> MC68160 Connections:
*
* Setup MPC823 to work with MC68160 Enhanced Ethernet
* Serial Tranceiver as follows:
*
* MPC823 Signal MC68160 Comments
* ------ ------ ------- --------
* PA-12 ETHTX --------> TX Eth. Port Transmit Data
* PB-18 E_TENA --------> TENA Eth. Transmit Port Enable
* PA-5 ETHTCK <-------- TCLK Eth. Port Transmit Clock
* PA-13 ETHRX <-------- RX Eth. Port Receive Data
* PC-8 E_RENA <-------- RENA Eth. Receive Enable
* PA-6 ETHRCK <-------- RCLK Eth. Port Receive Clock
* PC-9 E_CLSN <-------- CLSN Eth. Port Collision Indication
*
* FADS Board Signal MC68160 Comments
* ----------------- ------- --------
* (BCSR1) ETHEN* --------> CS2 Eth. Port Enable
* (BSCR4) TPSQEL* --------> TPSQEL Twisted Pair Signal Quality Error Test Enable
* (BCSR4) TPFLDL* --------> TPFLDL Twisted Pair Full-Duplex
* (BCSR4) ETHLOOP --------> LOOP Eth. Port Diagnostic Loop-Back
*
*/
#include <common.h>
#include <malloc.h>
#include <commproc.h>
#include <net.h>
#include <command.h>
#if defined(CONFIG_CMD_NET) && defined(SCC_ENET)
/* Ethernet Transmit and Receive Buffers */
#define DBUF_LENGTH 1520
#define TX_BUF_CNT 2
#define TOUT_LOOP 10000 /* 10 ms to have a packet sent */
static char txbuf[DBUF_LENGTH];
static uint rxIdx; /* index of the current RX buffer */
static uint txIdx; /* index of the current TX buffer */
/*
* SCC Ethernet Tx and Rx buffer descriptors allocated at the
* immr->udata_bd address on Dual-Port RAM
* Provide for Double Buffering
*/
typedef volatile struct CommonBufferDescriptor {
cbd_t rxbd[PKTBUFSRX]; /* Rx BD */
cbd_t txbd[TX_BUF_CNT]; /* Tx BD */
} RTXBD;
static RTXBD *rtx;
static int scc_send(struct eth_device *dev, void *packet, int length);
static int scc_recv(struct eth_device* dev);
static int scc_init (struct eth_device* dev, bd_t * bd);
static void scc_halt(struct eth_device* dev);
int scc_initialize(bd_t *bis)
{
struct eth_device* dev;
dev = (struct eth_device*) malloc(sizeof *dev);
memset(dev, 0, sizeof *dev);
sprintf(dev->name, "SCC");
dev->iobase = 0;
dev->priv = 0;
dev->init = scc_init;
dev->halt = scc_halt;
dev->send = scc_send;
dev->recv = scc_recv;
eth_register(dev);
return 1;
}
static int scc_send(struct eth_device *dev, void *packet, int length)
{
int i, j=0;
#if 0
volatile char *in, *out;
#endif
/* section 16.9.23.3
* Wait for ready
*/
#if 0
while (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY);
out = (char *)(rtx->txbd[txIdx].cbd_bufaddr);
in = packet;
for(i = 0; i < length; i++) {
*out++ = *in++;
}
rtx->txbd[txIdx].cbd_datlen = length;
rtx->txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST);
while (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) j++;
#ifdef ET_DEBUG
printf("cycles: %d status: %x\n", j, rtx->txbd[txIdx].cbd_sc);
#endif
i = (rtx->txbd[txIdx++].cbd_sc & BD_ENET_TX_STATS) /* return only status bits */;
/* wrap around buffer index when necessary */
if (txIdx >= TX_BUF_CNT) txIdx = 0;
#endif
while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
udelay (1); /* will also trigger Wd if needed */
j++;
}
if (j>=TOUT_LOOP) printf("TX not ready\n");
rtx->txbd[txIdx].cbd_bufaddr = (uint)packet;
rtx->txbd[txIdx].cbd_datlen = length;
rtx->txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST |BD_ENET_TX_WRAP);
while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
udelay (1); /* will also trigger Wd if needed */
j++;
}
if (j>=TOUT_LOOP) printf("TX timeout\n");
#ifdef ET_DEBUG
printf("cycles: %d status: %x\n", j, rtx->txbd[txIdx].cbd_sc);
#endif
i = (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_STATS) /* return only status bits */;
return i;
}
static int scc_recv (struct eth_device *dev)
{
int length;
for (;;) {
/* section 16.9.23.2 */
if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
length = -1;
break; /* nothing received - leave for() loop */
}
length = rtx->rxbd[rxIdx].cbd_datlen;
if (rtx->rxbd[rxIdx].cbd_sc & 0x003f) {
#ifdef ET_DEBUG
printf ("err: %x\n", rtx->rxbd[rxIdx].cbd_sc);
#endif
} else {
/* Pass the packet up to the protocol layers. */
NetReceive (NetRxPackets[rxIdx], length - 4);
}
/* Give the buffer back to the SCC. */
rtx->rxbd[rxIdx].cbd_datlen = 0;
/* wrap around buffer index when necessary */
if ((rxIdx + 1) >= PKTBUFSRX) {
rtx->rxbd[PKTBUFSRX - 1].cbd_sc =
(BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
rxIdx = 0;
} else {
rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
rxIdx++;
}
}
return length;
}
/**************************************************************
*
* SCC Ethernet Initialization Routine
*
*************************************************************/
static int scc_init (struct eth_device *dev, bd_t * bis)
{
int i;
scc_enet_t *pram_ptr;
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
#if defined(CONFIG_LWMON)
reset_phy();
#endif
#ifdef CONFIG_FADS
#if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC860T)
/* The MPC86xADS/FADS860T don't use the MODEM_EN or DATA_VOICE signals. */
*((uint *) BCSR4) &= ~BCSR4_ETHLOOP;
*((uint *) BCSR4) |= BCSR4_TFPLDL | BCSR4_TPSQEL;
*((uint *) BCSR1) &= ~BCSR1_ETHEN;
#else
*((uint *) BCSR4) &= ~(BCSR4_ETHLOOP | BCSR4_MODEM_EN);
*((uint *) BCSR4) |= BCSR4_TFPLDL | BCSR4_TPSQEL | BCSR4_DATA_VOICE;
*((uint *) BCSR1) &= ~BCSR1_ETHEN;
#endif
#endif
pram_ptr = (scc_enet_t *) & (immr->im_cpm.cp_dparam[PROFF_ENET]);
rxIdx = 0;
txIdx = 0;
if (!rtx) {
#ifdef CONFIG_SYS_ALLOC_DPRAM
rtx = (RTXBD *) (immr->im_cpm.cp_dpmem +
dpram_alloc_align (sizeof (RTXBD), 8));
#else
rtx = (RTXBD *) (immr->im_cpm.cp_dpmem + CPM_SCC_BASE);
#endif
}
#if (defined(PA_ENET_RXD) && defined(PA_ENET_TXD))
/* Configure port A pins for Txd and Rxd.
*/
immr->im_ioport.iop_papar |= (PA_ENET_RXD | PA_ENET_TXD);
immr->im_ioport.iop_padir &= ~(PA_ENET_RXD | PA_ENET_TXD);
immr->im_ioport.iop_paodr &= ~PA_ENET_TXD;
#elif (defined(PB_ENET_RXD) && defined(PB_ENET_TXD))
/* Configure port B pins for Txd and Rxd.
*/
immr->im_cpm.cp_pbpar |= (PB_ENET_RXD | PB_ENET_TXD);
immr->im_cpm.cp_pbdir &= ~(PB_ENET_RXD | PB_ENET_TXD);
immr->im_cpm.cp_pbodr &= ~PB_ENET_TXD;
#else
#error Configuration Error: exactly ONE of PA_ENET_[RT]XD, PB_ENET_[RT]XD must be defined
#endif
#if defined(PC_ENET_LBK)
/* Configure port C pins to disable External Loopback
*/
immr->im_ioport.iop_pcpar &= ~PC_ENET_LBK;
immr->im_ioport.iop_pcdir |= PC_ENET_LBK;
immr->im_ioport.iop_pcso &= ~PC_ENET_LBK;
immr->im_ioport.iop_pcdat &= ~PC_ENET_LBK; /* Disable Loopback */
#endif /* PC_ENET_LBK */
/* Configure port C pins to enable CLSN and RENA.
*/
immr->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
immr->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
immr->im_ioport.iop_pcso |= (PC_ENET_CLSN | PC_ENET_RENA);
/* Configure port A for TCLK and RCLK.
*/
immr->im_ioport.iop_papar |= (PA_ENET_TCLK | PA_ENET_RCLK);
immr->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
/*
* Configure Serial Interface clock routing -- see section 16.7.5.3
* First, clear all SCC bits to zero, then set the ones we want.
*/
immr->im_cpm.cp_sicr &= ~SICR_ENET_MASK;
immr->im_cpm.cp_sicr |= SICR_ENET_CLKRT;
/*
* Initialize SDCR -- see section 16.9.23.7
* SDMA configuration register
*/
immr->im_siu_conf.sc_sdcr = 0x01;
/*
* Setup SCC Ethernet Parameter RAM
*/
pram_ptr->sen_genscc.scc_rfcr = 0x18; /* Normal Operation and Mot byte ordering */
pram_ptr->sen_genscc.scc_tfcr = 0x18; /* Mot byte ordering, Normal access */
pram_ptr->sen_genscc.scc_mrblr = DBUF_LENGTH; /* max. ET package len 1520 */
pram_ptr->sen_genscc.scc_rbase = (unsigned int) (&rtx->rxbd[0]); /* Set RXBD tbl start at Dual Port */
pram_ptr->sen_genscc.scc_tbase = (unsigned int) (&rtx->txbd[0]); /* Set TXBD tbl start at Dual Port */
/*
* Setup Receiver Buffer Descriptors (13.14.24.18)
* Settings:
* Empty, Wrap
*/
for (i = 0; i < PKTBUFSRX; i++) {
rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
rtx->rxbd[i].cbd_datlen = 0; /* Reset */
rtx->rxbd[i].cbd_bufaddr = (uint) NetRxPackets[i];
}
rtx->rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
/*
* Setup Ethernet Transmitter Buffer Descriptors (13.14.24.19)
* Settings:
* Add PADs to Short FRAMES, Wrap, Last, Tx CRC
*/
for (i = 0; i < TX_BUF_CNT; i++) {
rtx->txbd[i].cbd_sc =
(BD_ENET_TX_PAD | BD_ENET_TX_LAST | BD_ENET_TX_TC);
rtx->txbd[i].cbd_datlen = 0; /* Reset */
rtx->txbd[i].cbd_bufaddr = (uint) (&txbuf[0]);
}
rtx->txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
/*
* Enter Command: Initialize Rx Params for SCC
*/
do { /* Spin until ready to issue command */
__asm__ ("eieio");
} while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
/* Issue command */
immr->im_cpm.cp_cpcr =
((CPM_CR_INIT_RX << 8) | (CPM_CR_ENET << 4) | CPM_CR_FLG);
do { /* Spin until command processed */
__asm__ ("eieio");
} while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
/*
* Ethernet Specific Parameter RAM
* see table 13-16, pg. 660,
* pg. 681 (example with suggested settings)
*/
pram_ptr->sen_cpres = ~(0x0); /* Preset CRC */
pram_ptr->sen_cmask = 0xdebb20e3; /* Constant Mask for CRC */
pram_ptr->sen_crcec = 0x0; /* Error Counter CRC (unused) */
pram_ptr->sen_alec = 0x0; /* Alignment Error Counter (unused) */
pram_ptr->sen_disfc = 0x0; /* Discard Frame Counter (unused) */
pram_ptr->sen_pads = 0x8888; /* Short Frame PAD Characters */
pram_ptr->sen_retlim = 15; /* Retry Limit Threshold */
pram_ptr->sen_maxflr = 1518; /* MAX Frame Length Register */
pram_ptr->sen_minflr = 64; /* MIN Frame Length Register */
pram_ptr->sen_maxd1 = DBUF_LENGTH; /* MAX DMA1 Length Register */
pram_ptr->sen_maxd2 = DBUF_LENGTH; /* MAX DMA2 Length Register */
pram_ptr->sen_gaddr1 = 0x0; /* Group Address Filter 1 (unused) */
pram_ptr->sen_gaddr2 = 0x0; /* Group Address Filter 2 (unused) */
pram_ptr->sen_gaddr3 = 0x0; /* Group Address Filter 3 (unused) */
pram_ptr->sen_gaddr4 = 0x0; /* Group Address Filter 4 (unused) */
#define ea eth_get_dev()->enetaddr
pram_ptr->sen_paddrh = (ea[5] << 8) + ea[4];
pram_ptr->sen_paddrm = (ea[3] << 8) + ea[2];
pram_ptr->sen_paddrl = (ea[1] << 8) + ea[0];
#undef ea
pram_ptr->sen_pper = 0x0; /* Persistence (unused) */
pram_ptr->sen_iaddr1 = 0x0; /* Individual Address Filter 1 (unused) */
pram_ptr->sen_iaddr2 = 0x0; /* Individual Address Filter 2 (unused) */
pram_ptr->sen_iaddr3 = 0x0; /* Individual Address Filter 3 (unused) */
pram_ptr->sen_iaddr4 = 0x0; /* Individual Address Filter 4 (unused) */
pram_ptr->sen_taddrh = 0x0; /* Tmp Address (MSB) (unused) */
pram_ptr->sen_taddrm = 0x0; /* Tmp Address (unused) */
pram_ptr->sen_taddrl = 0x0; /* Tmp Address (LSB) (unused) */
/*
* Enter Command: Initialize Tx Params for SCC
*/
do { /* Spin until ready to issue command */
__asm__ ("eieio");
} while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
/* Issue command */
immr->im_cpm.cp_cpcr =
((CPM_CR_INIT_TX << 8) | (CPM_CR_ENET << 4) | CPM_CR_FLG);
do { /* Spin until command processed */
__asm__ ("eieio");
} while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
/*
* Mask all Events in SCCM - we use polling mode
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_sccm = 0;
/*
* Clear Events in SCCE -- Clear bits by writing 1's
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_scce = ~(0x0);
/*
* Initialize GSMR High 32-Bits
* Settings: Normal Mode
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrh = 0;
/*
* Initialize GSMR Low 32-Bits, but do not Enable Transmit/Receive
* Settings:
* TCI = Invert
* TPL = 48 bits
* TPP = Repeating 10's
* MODE = Ethernet
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl = (SCC_GSMRL_TCI |
SCC_GSMRL_TPL_48 |
SCC_GSMRL_TPP_10 |
SCC_GSMRL_MODE_ENET);
/*
* Initialize the DSR -- see section 13.14.4 (pg. 513) v0.4
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_dsr = 0xd555;
/*
* Initialize the PSMR
* Settings:
* CRC = 32-Bit CCITT
* NIB = Begin searching for SFD 22 bits after RENA
* FDE = Full Duplex Enable
* LPB = Loopback Enable (Needed when FDE is set)
* BRO = Reject broadcast packets
* PROMISCOUS = Catch all packets regardless of dest. MAC adress
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_psmr = SCC_PSMR_ENCRC |
SCC_PSMR_NIB22 |
#if defined(CONFIG_SCC_ENET_FULL_DUPLEX)
SCC_PSMR_FDE | SCC_PSMR_LPB |
#endif
#if defined(CONFIG_SCC_ENET_NO_BROADCAST)
SCC_PSMR_BRO |
#endif
#if defined(CONFIG_SCC_ENET_PROMISCOUS)
SCC_PSMR_PRO |
#endif
0;
/*
* Configure Ethernet TENA Signal
*/
#if (defined(PC_ENET_TENA) && !defined(PB_ENET_TENA))
immr->im_ioport.iop_pcpar |= PC_ENET_TENA;
immr->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
#elif (defined(PB_ENET_TENA) && !defined(PC_ENET_TENA))
immr->im_cpm.cp_pbpar |= PB_ENET_TENA;
immr->im_cpm.cp_pbdir |= PB_ENET_TENA;
#else
#error Configuration Error: exactly ONE of PB_ENET_TENA, PC_ENET_TENA must be defined
#endif
#if defined(CONFIG_ADS) && defined(CONFIG_MPC860)
/*
* Port C is used to control the PHY,MC68160.
*/
immr->im_ioport.iop_pcdir |=
(PC_ENET_ETHLOOP | PC_ENET_TPFLDL | PC_ENET_TPSQEL);
immr->im_ioport.iop_pcdat |= PC_ENET_TPFLDL;
immr->im_ioport.iop_pcdat &= ~(PC_ENET_ETHLOOP | PC_ENET_TPSQEL);
*((uint *) BCSR1) &= ~BCSR1_ETHEN;
#endif /* MPC860ADS */
#ifdef CONFIG_RPXCLASSIC
*((uchar *) BCSR0) &= ~BCSR0_ETHLPBK;
*((uchar *) BCSR0) |= (BCSR0_ETHEN | BCSR0_COLTEST | BCSR0_FULLDPLX);
#endif
#ifdef CONFIG_RPXLITE
*((uchar *) BCSR0) |= BCSR0_ETHEN;
#endif
#if defined(CONFIG_QS860T)
/*
* PB27=FDE-, set output low for full duplex
* PB26=Link Test Enable, normally high output
*/
immr->im_cpm.cp_pbdir |= 0x00000030;
immr->im_cpm.cp_pbdat |= 0x00000020;
immr->im_cpm.cp_pbdat &= ~0x00000010;
#endif /* QS860T */
#ifdef CONFIG_MBX
board_ether_init ();
#endif
#if defined(CONFIG_NETVIA)
#if defined(PA_ENET_PDN)
immr->im_ioport.iop_papar &= ~PA_ENET_PDN;
immr->im_ioport.iop_padir |= PA_ENET_PDN;
immr->im_ioport.iop_padat |= PA_ENET_PDN;
#elif defined(PB_ENET_PDN)
immr->im_cpm.cp_pbpar &= ~PB_ENET_PDN;
immr->im_cpm.cp_pbdir |= PB_ENET_PDN;
immr->im_cpm.cp_pbdat |= PB_ENET_PDN;
#elif defined(PC_ENET_PDN)
immr->im_ioport.iop_pcpar &= ~PC_ENET_PDN;
immr->im_ioport.iop_pcdir |= PC_ENET_PDN;
immr->im_ioport.iop_pcdat |= PC_ENET_PDN;
#elif defined(PD_ENET_PDN)
immr->im_ioport.iop_pdpar &= ~PD_ENET_PDN;
immr->im_ioport.iop_pddir |= PD_ENET_PDN;
immr->im_ioport.iop_pddat |= PD_ENET_PDN;
#endif
#endif
/*
* Set the ENT/ENR bits in the GSMR Low -- Enable Transmit/Receive
*/
immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |=
(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
/*
* Work around transmit problem with first eth packet
*/
#if defined (CONFIG_FADS)
udelay (10000); /* wait 10 ms */
#elif defined(CONFIG_RPXCLASSIC)
udelay (100000); /* wait 100 ms */
#endif
return 1;
}
static void scc_halt (struct eth_device *dev)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl &=
~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
immr->im_ioport.iop_pcso &= ~(PC_ENET_CLSN | PC_ENET_RENA);
}
#if 0
void restart (void)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |=
(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
#endif
#endif