u-boot/board/freescale/ls2080ardb/ls2080ardb.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

446 lines
9.2 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017 NXP Semiconductors
* Copyright 2015 Freescale Semiconductor
*/
#include <common.h>
#include <malloc.h>
#include <errno.h>
#include <netdev.h>
#include <fsl_ifc.h>
#include <fsl_ddr.h>
#include <asm/io.h>
#include <hwconfig.h>
#include <fdt_support.h>
#include <linux/libfdt.h>
#include <fsl-mc/fsl_mc.h>
#include <environment.h>
#include <efi_loader.h>
#include <i2c.h>
#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <asm/arch/ppa.h>
#include <fsl_sec.h>
#ifdef CONFIG_FSL_QIXIS
#include "../common/qixis.h"
#include "ls2080ardb_qixis.h"
#endif
#include "../common/vid.h"
#define PIN_MUX_SEL_SDHC 0x00
#define PIN_MUX_SEL_DSPI 0x0a
#define SET_SDHC_MUX_SEL(reg, value) ((reg & 0xf0) | value)
DECLARE_GLOBAL_DATA_PTR;
enum {
MUX_TYPE_SDHC,
MUX_TYPE_DSPI,
};
unsigned long long get_qixis_addr(void)
{
unsigned long long addr;
if (gd->flags & GD_FLG_RELOC)
addr = QIXIS_BASE_PHYS;
else
addr = QIXIS_BASE_PHYS_EARLY;
/*
* IFC address under 256MB is mapped to 0x30000000, any address above
* is mapped to 0x5_10000000 up to 4GB.
*/
addr = addr > 0x10000000 ? addr + 0x500000000ULL : addr + 0x30000000;
return addr;
}
int checkboard(void)
{
#ifdef CONFIG_FSL_QIXIS
u8 sw;
#endif
char buf[15];
cpu_name(buf);
printf("Board: %s-RDB, ", buf);
#ifdef CONFIG_TARGET_LS2081ARDB
#ifdef CONFIG_FSL_QIXIS
sw = QIXIS_READ(arch);
printf("Board version: %c, ", (sw & 0xf) + 'A');
sw = QIXIS_READ(brdcfg[0]);
sw = (sw >> QIXIS_QMAP_SHIFT) & QIXIS_QMAP_MASK;
switch (sw) {
case 0:
puts("boot from QSPI DEV#0\n");
puts("QSPI_CSA_1 mapped to QSPI DEV#1\n");
break;
case 1:
puts("boot from QSPI DEV#1\n");
puts("QSPI_CSA_1 mapped to QSPI DEV#0\n");
break;
case 2:
puts("boot from QSPI EMU\n");
puts("QSPI_CSA_1 mapped to QSPI DEV#0\n");
break;
case 3:
puts("boot from QSPI EMU\n");
puts("QSPI_CSA_1 mapped to QSPI DEV#1\n");
break;
case 4:
puts("boot from QSPI DEV#0\n");
puts("QSPI_CSA_1 mapped to QSPI EMU\n");
break;
default:
printf("invalid setting of SW%u\n", sw);
break;
}
printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
#endif
puts("SERDES1 Reference : ");
printf("Clock1 = 100MHz ");
printf("Clock2 = 161.13MHz");
#else
#ifdef CONFIG_FSL_QIXIS
sw = QIXIS_READ(arch);
printf("Board Arch: V%d, ", sw >> 4);
printf("Board version: %c, boot from ", (sw & 0xf) + 'A');
sw = QIXIS_READ(brdcfg[0]);
sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
if (sw < 0x8)
printf("vBank: %d\n", sw);
else if (sw == 0x9)
puts("NAND\n");
else
printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata));
#endif
puts("SERDES1 Reference : ");
printf("Clock1 = 156.25MHz ");
printf("Clock2 = 156.25MHz");
#endif
puts("\nSERDES2 Reference : ");
printf("Clock1 = 100MHz ");
printf("Clock2 = 100MHz\n");
return 0;
}
unsigned long get_board_sys_clk(void)
{
#ifdef CONFIG_FSL_QIXIS
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
switch (sysclk_conf & 0x0F) {
case QIXIS_SYSCLK_83:
return 83333333;
case QIXIS_SYSCLK_100:
return 100000000;
case QIXIS_SYSCLK_125:
return 125000000;
case QIXIS_SYSCLK_133:
return 133333333;
case QIXIS_SYSCLK_150:
return 150000000;
case QIXIS_SYSCLK_160:
return 160000000;
case QIXIS_SYSCLK_166:
return 166666666;
}
#endif
return 100000000;
}
int select_i2c_ch_pca9547(u8 ch)
{
int ret;
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
if (ret) {
puts("PCA: failed to select proper channel\n");
return ret;
}
return 0;
}
int i2c_multiplexer_select_vid_channel(u8 channel)
{
return select_i2c_ch_pca9547(channel);
}
int config_board_mux(int ctrl_type)
{
#ifdef CONFIG_FSL_QIXIS
u8 reg5;
reg5 = QIXIS_READ(brdcfg[5]);
switch (ctrl_type) {
case MUX_TYPE_SDHC:
reg5 = SET_SDHC_MUX_SEL(reg5, PIN_MUX_SEL_SDHC);
break;
case MUX_TYPE_DSPI:
reg5 = SET_SDHC_MUX_SEL(reg5, PIN_MUX_SEL_DSPI);
break;
default:
printf("Wrong mux interface type\n");
return -1;
}
QIXIS_WRITE(brdcfg[5], reg5);
#endif
return 0;
}
int board_init(void)
{
#ifdef CONFIG_FSL_MC_ENET
u32 __iomem *irq_ccsr = (u32 __iomem *)ISC_BASE;
#endif
init_final_memctl_regs();
#ifdef CONFIG_ENV_IS_NOWHERE
gd->env_addr = (ulong)&default_environment[0];
#endif
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
#ifdef CONFIG_FSL_QIXIS
QIXIS_WRITE(rst_ctl, QIXIS_RST_CTL_RESET_EN);
#endif
#ifdef CONFIG_FSL_CAAM
sec_init();
#endif
#ifdef CONFIG_FSL_LS_PPA
ppa_init();
#endif
#ifdef CONFIG_FSL_MC_ENET
/* invert AQR405 IRQ pins polarity */
out_le32(irq_ccsr + IRQCR_OFFSET / 4, AQR405_IRQ_MASK);
#endif
#ifdef CONFIG_FSL_CAAM
sec_init();
#endif
return 0;
}
int board_early_init_f(void)
{
#ifdef CONFIG_SYS_I2C_EARLY_INIT
i2c_early_init_f();
#endif
fsl_lsch3_early_init_f();
return 0;
}
int misc_init_r(void)
{
char *env_hwconfig;
u32 __iomem *dcfg_ccsr = (u32 __iomem *)DCFG_BASE;
u32 val;
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
u32 svr = gur_in32(&gur->svr);
val = in_le32(dcfg_ccsr + DCFG_RCWSR13 / 4);
env_hwconfig = env_get("hwconfig");
if (hwconfig_f("dspi", env_hwconfig) &&
DCFG_RCWSR13_DSPI == (val & (u32)(0xf << 8)))
config_board_mux(MUX_TYPE_DSPI);
else
config_board_mux(MUX_TYPE_SDHC);
/*
* LS2081ARDB RevF board has smart voltage translator
* which needs to be programmed to enable high speed SD interface
* by setting GPIO4_10 output to zero
*/
#ifdef CONFIG_TARGET_LS2081ARDB
out_le32(GPIO4_GPDIR_ADDR, (1 << 21 |
in_le32(GPIO4_GPDIR_ADDR)));
out_le32(GPIO4_GPDAT_ADDR, (~(1 << 21) &
in_le32(GPIO4_GPDAT_ADDR)));
#endif
if (hwconfig("sdhc"))
config_board_mux(MUX_TYPE_SDHC);
if (adjust_vdd(0))
printf("Warning: Adjusting core voltage failed.\n");
/*
* Default value of board env is based on filename which is
* ls2080ardb. Modify board env for other supported SoCs
*/
if ((SVR_SOC_VER(svr) == SVR_LS2088A) ||
(SVR_SOC_VER(svr) == SVR_LS2048A))
env_set("board", "ls2088ardb");
else if ((SVR_SOC_VER(svr) == SVR_LS2081A) ||
(SVR_SOC_VER(svr) == SVR_LS2041A))
env_set("board", "ls2081ardb");
return 0;
}
void detail_board_ddr_info(void)
{
puts("\nDDR ");
print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
print_ddr_info(0);
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (soc_has_dp_ddr() && gd->bd->bi_dram[2].size) {
puts("\nDP-DDR ");
print_size(gd->bd->bi_dram[2].size, "");
print_ddr_info(CONFIG_DP_DDR_CTRL);
}
#endif
}
#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
return 0;
}
#endif
#ifdef CONFIG_FSL_MC_ENET
void fdt_fixup_board_enet(void *fdt)
{
int offset;
offset = fdt_path_offset(fdt, "/soc/fsl-mc");
if (offset < 0)
offset = fdt_path_offset(fdt, "/fsl-mc");
if (offset < 0) {
printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
__func__, offset);
return;
}
if ((get_mc_boot_status() == 0) && (get_dpl_apply_status() == 0))
fdt_status_okay(fdt, offset);
else
fdt_status_fail(fdt, offset);
}
void board_quiesce_devices(void)
{
fsl_mc_ldpaa_exit(gd->bd);
}
#endif
#ifdef CONFIG_OF_BOARD_SETUP
void fsl_fdt_fixup_flash(void *fdt)
{
int offset;
/*
* IFC and QSPI are muxed on board.
* So disable IFC node in dts if QSPI is enabled or
* disable QSPI node in dts in case QSPI is not enabled.
*/
#ifdef CONFIG_FSL_QSPI
offset = fdt_path_offset(fdt, "/soc/ifc");
if (offset < 0)
offset = fdt_path_offset(fdt, "/ifc");
#else
offset = fdt_path_offset(fdt, "/soc/quadspi");
if (offset < 0)
offset = fdt_path_offset(fdt, "/quadspi");
#endif
if (offset < 0)
return;
fdt_status_disabled(fdt, offset);
}
int ft_board_setup(void *blob, bd_t *bd)
{
u64 base[CONFIG_NR_DRAM_BANKS];
u64 size[CONFIG_NR_DRAM_BANKS];
ft_cpu_setup(blob, bd);
/* fixup DT for the two GPP DDR banks */
base[0] = gd->bd->bi_dram[0].start;
size[0] = gd->bd->bi_dram[0].size;
base[1] = gd->bd->bi_dram[1].start;
size[1] = gd->bd->bi_dram[1].size;
#ifdef CONFIG_RESV_RAM
/* reduce size if reserved memory is within this bank */
if (gd->arch.resv_ram >= base[0] &&
gd->arch.resv_ram < base[0] + size[0])
size[0] = gd->arch.resv_ram - base[0];
else if (gd->arch.resv_ram >= base[1] &&
gd->arch.resv_ram < base[1] + size[1])
size[1] = gd->arch.resv_ram - base[1];
#endif
fdt_fixup_memory_banks(blob, base, size, 2);
fsl_fdt_fixup_dr_usb(blob, bd);
fsl_fdt_fixup_flash(blob);
#ifdef CONFIG_FSL_MC_ENET
fdt_fixup_board_enet(blob);
#endif
return 0;
}
#endif
void qixis_dump_switch(void)
{
#ifdef CONFIG_FSL_QIXIS
int i, nr_of_cfgsw;
QIXIS_WRITE(cms[0], 0x00);
nr_of_cfgsw = QIXIS_READ(cms[1]);
puts("DIP switch settings dump:\n");
for (i = 1; i <= nr_of_cfgsw; i++) {
QIXIS_WRITE(cms[0], i);
printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
}
#endif
}
/*
* Board rev C and earlier has duplicated I2C addresses for 2nd controller.
* Both slots has 0x54, resulting 2nd slot unusable.
*/
void update_spd_address(unsigned int ctrl_num,
unsigned int slot,
unsigned int *addr)
{
#ifndef CONFIG_TARGET_LS2081ARDB
#ifdef CONFIG_FSL_QIXIS
u8 sw;
sw = QIXIS_READ(arch);
if ((sw & 0xf) < 0x3) {
if (ctrl_num == 1 && slot == 0)
*addr = SPD_EEPROM_ADDRESS4;
else if (ctrl_num == 1 && slot == 1)
*addr = SPD_EEPROM_ADDRESS3;
}
#endif
#endif
}