u-boot/board/freescale/ls1043aqds/ls1043aqds.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

385 lines
7.9 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <i2c.h>
#include <fdt_support.h>
#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch/ppa.h>
#include <asm/arch/fdt.h>
#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <ahci.h>
#include <hwconfig.h>
#include <mmc.h>
#include <scsi.h>
#include <fm_eth.h>
#include <fsl_esdhc.h>
#include <fsl_ifc.h>
#include <spl.h>
#include "../common/qixis.h"
#include "ls1043aqds_qixis.h"
DECLARE_GLOBAL_DATA_PTR;
enum {
MUX_TYPE_GPIO,
};
/* LS1043AQDS serdes mux */
#define CFG_SD_MUX1_SLOT2 0x0 /* SLOT2 TX/RX0 */
#define CFG_SD_MUX1_SLOT1 0x1 /* SLOT1 TX/RX1 */
#define CFG_SD_MUX2_SLOT3 0x0 /* SLOT3 TX/RX0 */
#define CFG_SD_MUX2_SLOT1 0x1 /* SLOT1 TX/RX2 */
#define CFG_SD_MUX3_SLOT4 0x0 /* SLOT4 TX/RX0 */
#define CFG_SD_MUX3_MUX4 0x1 /* MUX4 */
#define CFG_SD_MUX4_SLOT3 0x0 /* SLOT3 TX/RX1 */
#define CFG_SD_MUX4_SLOT1 0x1 /* SLOT1 TX/RX3 */
#define CFG_UART_MUX_MASK 0x6
#define CFG_UART_MUX_SHIFT 1
#define CFG_LPUART_EN 0x1
int checkboard(void)
{
char buf[64];
#ifndef CONFIG_SD_BOOT
u8 sw;
#endif
puts("Board: LS1043AQDS, boot from ");
#ifdef CONFIG_SD_BOOT
puts("SD\n");
#else
sw = QIXIS_READ(brdcfg[0]);
sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
if (sw < 0x8)
printf("vBank: %d\n", sw);
else if (sw == 0x8)
puts("PromJet\n");
else if (sw == 0x9)
puts("NAND\n");
else if (sw == 0xF)
printf("QSPI\n");
else
printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
#endif
printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n",
QIXIS_READ(id), QIXIS_READ(arch));
printf("FPGA: v%d (%s), build %d\n",
(int)QIXIS_READ(scver), qixis_read_tag(buf),
(int)qixis_read_minor());
return 0;
}
bool if_board_diff_clk(void)
{
u8 diff_conf = QIXIS_READ(brdcfg[11]);
return diff_conf & 0x40;
}
unsigned long get_board_sys_clk(void)
{
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
switch (sysclk_conf & 0x0f) {
case QIXIS_SYSCLK_64:
return 64000000;
case QIXIS_SYSCLK_83:
return 83333333;
case QIXIS_SYSCLK_100:
return 100000000;
case QIXIS_SYSCLK_125:
return 125000000;
case QIXIS_SYSCLK_133:
return 133333333;
case QIXIS_SYSCLK_150:
return 150000000;
case QIXIS_SYSCLK_160:
return 160000000;
case QIXIS_SYSCLK_166:
return 166666666;
}
return 66666666;
}
unsigned long get_board_ddr_clk(void)
{
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
if (if_board_diff_clk())
return get_board_sys_clk();
switch ((ddrclk_conf & 0x30) >> 4) {
case QIXIS_DDRCLK_100:
return 100000000;
case QIXIS_DDRCLK_125:
return 125000000;
case QIXIS_DDRCLK_133:
return 133333333;
}
return 66666666;
}
int select_i2c_ch_pca9547(u8 ch)
{
int ret;
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
if (ret) {
puts("PCA: failed to select proper channel\n");
return ret;
}
return 0;
}
int dram_init(void)
{
/*
* When resuming from deep sleep, the I2C channel may not be
* in the default channel. So, switch to the default channel
* before accessing DDR SPD.
*/
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
fsl_initdram();
#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
/* This will break-before-make MMU for DDR */
update_early_mmu_table();
#endif
return 0;
}
int i2c_multiplexer_select_vid_channel(u8 channel)
{
return select_i2c_ch_pca9547(channel);
}
void board_retimer_init(void)
{
u8 reg;
/* Retimer is connected to I2C1_CH7_CH5 */
select_i2c_ch_pca9547(I2C_MUX_CH7);
reg = I2C_MUX_CH5;
i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, &reg, 1);
/* Access to Control/Shared register */
reg = 0x0;
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
/* Read device revision and ID */
i2c_read(I2C_RETIMER_ADDR, 1, 1, &reg, 1);
debug("Retimer version id = 0x%x\n", reg);
/* Enable Broadcast. All writes target all channel register sets */
reg = 0x0c;
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
/* Reset Channel Registers */
i2c_read(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
reg |= 0x4;
i2c_write(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
/* Enable override divider select and Enable Override Output Mux */
i2c_read(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
reg |= 0x24;
i2c_write(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
/* Select VCO Divider to full rate (000) */
i2c_read(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
reg &= 0x8f;
i2c_write(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
/* Selects active PFD MUX Input as Re-timed Data (001) */
i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
reg &= 0x3f;
reg |= 0x20;
i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
/* Set data rate as 10.3125 Gbps */
reg = 0x0;
i2c_write(I2C_RETIMER_ADDR, 0x60, 1, &reg, 1);
reg = 0xb2;
i2c_write(I2C_RETIMER_ADDR, 0x61, 1, &reg, 1);
reg = 0x90;
i2c_write(I2C_RETIMER_ADDR, 0x62, 1, &reg, 1);
reg = 0xb3;
i2c_write(I2C_RETIMER_ADDR, 0x63, 1, &reg, 1);
reg = 0xcd;
i2c_write(I2C_RETIMER_ADDR, 0x64, 1, &reg, 1);
/* Return the default channel */
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
}
int board_early_init_f(void)
{
#ifdef CONFIG_HAS_FSL_XHCI_USB
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
u32 usb_pwrfault;
#endif
#ifdef CONFIG_LPUART
u8 uart;
#endif
#ifdef CONFIG_SYS_I2C_EARLY_INIT
i2c_early_init_f();
#endif
fsl_lsch2_early_init_f();
#ifdef CONFIG_HAS_FSL_XHCI_USB
out_be32(&scfg->rcwpmuxcr0, 0x3333);
out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
usb_pwrfault =
(SCFG_USBPWRFAULT_DEDICATED << SCFG_USBPWRFAULT_USB3_SHIFT) |
(SCFG_USBPWRFAULT_DEDICATED << SCFG_USBPWRFAULT_USB2_SHIFT) |
(SCFG_USBPWRFAULT_SHARED << SCFG_USBPWRFAULT_USB1_SHIFT);
out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
#endif
#ifdef CONFIG_LPUART
/* We use lpuart0 as system console */
uart = QIXIS_READ(brdcfg[14]);
uart &= ~CFG_UART_MUX_MASK;
uart |= CFG_LPUART_EN << CFG_UART_MUX_SHIFT;
QIXIS_WRITE(brdcfg[14], uart);
#endif
return 0;
}
#ifdef CONFIG_FSL_DEEP_SLEEP
/* determine if it is a warm boot */
bool is_warm_boot(void)
{
#define DCFG_CCSR_CRSTSR_WDRFR (1 << 3)
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
if (in_be32(&gur->crstsr) & DCFG_CCSR_CRSTSR_WDRFR)
return 1;
return 0;
}
#endif
int config_board_mux(int ctrl_type)
{
u8 reg14;
reg14 = QIXIS_READ(brdcfg[14]);
switch (ctrl_type) {
case MUX_TYPE_GPIO:
reg14 = (reg14 & (~0x30)) | 0x20;
break;
default:
puts("Unsupported mux interface type\n");
return -1;
}
QIXIS_WRITE(brdcfg[14], reg14);
return 0;
}
int config_serdes_mux(void)
{
return 0;
}
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
if (hwconfig("gpio"))
config_board_mux(MUX_TYPE_GPIO);
return 0;
}
#endif
int board_init(void)
{
#ifdef CONFIG_SYS_FSL_ERRATUM_A010315
erratum_a010315();
#endif
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
board_retimer_init();
#ifdef CONFIG_SYS_FSL_SERDES
config_serdes_mux();
#endif
#ifdef CONFIG_FSL_LS_PPA
ppa_init();
#endif
return 0;
}
#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
u64 base[CONFIG_NR_DRAM_BANKS];
u64 size[CONFIG_NR_DRAM_BANKS];
u8 reg;
/* fixup DT for the two DDR banks */
base[0] = gd->bd->bi_dram[0].start;
size[0] = gd->bd->bi_dram[0].size;
base[1] = gd->bd->bi_dram[1].start;
size[1] = gd->bd->bi_dram[1].size;
fdt_fixup_memory_banks(blob, base, size, 2);
ft_cpu_setup(blob, bd);
#ifdef CONFIG_SYS_DPAA_FMAN
fdt_fixup_fman_ethernet(blob);
fdt_fixup_board_enet(blob);
#endif
reg = QIXIS_READ(brdcfg[0]);
reg = (reg & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
/* Disable IFC if QSPI is enabled */
if (reg == 0xF)
do_fixup_by_compat(blob, "fsl,ifc",
"status", "disabled", 8 + 1, 1);
return 0;
}
#endif
u8 flash_read8(void *addr)
{
return __raw_readb(addr + 1);
}
void flash_write16(u16 val, void *addr)
{
u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
__raw_writew(shftval, addr);
}
u16 flash_read16(void *addr)
{
u16 val = __raw_readw(addr);
return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
}