mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
aba8004818
T1024QDS is a high-performance computing evaluation, development and test platform for T1024 QorIQ Power Architecture processor. T1024QDS board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Three 1G/2.5Gbps SGMII ports - Four 1Gbps QSGMII ports - one 10Gbps XFI or 10Base-KR interface - SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora - PCIe: Three PCI Express controllers with five PCIe slots. - IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - Video: DIU supports video up to 1280x1024x32 bpp. - Chrontel CH7201 for HDMI connection. - TI DS90C387R for direct LCD connection. - Raw (not encoded) video connector for testing or other encoders. - QUICC Engine block - 32-bit RISC controller for flexible support of the communications peripherals - Serial DMA channel for receive and transmit on all serial channels - Two universal communication controllers, supporting TDM, HDLC, and UART - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - eSPI: Three SPI flash devices. - SATA: one SATA 2.O. - USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC. - I2C: Four I2C controllers. - UART: Two UART on board. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
151 lines
3.4 KiB
C
151 lines
3.4 KiB
C
/* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <ns16550.h>
|
|
#include <nand.h>
|
|
#include <i2c.h>
|
|
#include <mmc.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <spi_flash.h>
|
|
#include "../common/qixis.h"
|
|
#include "t102xqds_qixis.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
phys_size_t get_effective_memsize(void)
|
|
{
|
|
return CONFIG_SYS_L3_SIZE;
|
|
}
|
|
|
|
unsigned long get_board_sys_clk(void)
|
|
{
|
|
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
|
|
|
|
switch (sysclk_conf & 0x0F) {
|
|
case QIXIS_SYSCLK_83:
|
|
return 83333333;
|
|
case QIXIS_SYSCLK_100:
|
|
return 100000000;
|
|
case QIXIS_SYSCLK_125:
|
|
return 125000000;
|
|
case QIXIS_SYSCLK_133:
|
|
return 133333333;
|
|
case QIXIS_SYSCLK_150:
|
|
return 150000000;
|
|
case QIXIS_SYSCLK_160:
|
|
return 160000000;
|
|
case QIXIS_SYSCLK_166:
|
|
return 166666666;
|
|
}
|
|
return 66666666;
|
|
}
|
|
|
|
unsigned long get_board_ddr_clk(void)
|
|
{
|
|
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
|
|
|
|
switch ((ddrclk_conf & 0x30) >> 4) {
|
|
case QIXIS_DDRCLK_100:
|
|
return 100000000;
|
|
case QIXIS_DDRCLK_125:
|
|
return 125000000;
|
|
case QIXIS_DDRCLK_133:
|
|
return 133333333;
|
|
}
|
|
return 66666666;
|
|
}
|
|
|
|
void board_init_f(ulong bootflag)
|
|
{
|
|
u32 plat_ratio, sys_clk, ccb_clk;
|
|
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
|
|
|
|
#if defined(CONFIG_PPC_T1040) && defined(CONFIG_SPL_NAND_BOOT)
|
|
/*
|
|
* There is T1040 SoC issue where NOR, FPGA are inaccessible during
|
|
* NAND boot because IFC signals > IFC_AD7 are not enabled.
|
|
* This workaround changes RCW source to make all signals enabled.
|
|
*/
|
|
u32 porsr1, pinctl;
|
|
#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000
|
|
|
|
porsr1 = in_be32(&gur->porsr1);
|
|
pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
|
|
out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
|
|
#endif
|
|
|
|
/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
|
|
memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
|
|
|
|
/* Update GD pointer */
|
|
gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
|
|
|
|
console_init_f();
|
|
|
|
/* initialize selected port with appropriate baud rate */
|
|
sys_clk = get_board_sys_clk();
|
|
plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
|
|
ccb_clk = sys_clk * plat_ratio / 2;
|
|
|
|
NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
|
|
ccb_clk / 16 / CONFIG_BAUDRATE);
|
|
|
|
#if defined(CONFIG_SPL_MMC_BOOT)
|
|
puts("\nSD boot...\n");
|
|
#elif defined(CONFIG_SPL_SPI_BOOT)
|
|
puts("\nSPI boot...\n");
|
|
#elif defined(CONFIG_SPL_NAND_BOOT)
|
|
puts("\nNAND boot...\n");
|
|
#endif
|
|
|
|
relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
|
|
}
|
|
|
|
void board_init_r(gd_t *gd, ulong dest_addr)
|
|
{
|
|
bd_t *bd;
|
|
|
|
bd = (bd_t *)(gd + sizeof(gd_t));
|
|
memset(bd, 0, sizeof(bd_t));
|
|
gd->bd = bd;
|
|
bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
|
|
bd->bi_memsize = CONFIG_SYS_L3_SIZE;
|
|
|
|
probecpu();
|
|
get_clocks();
|
|
mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
|
|
CONFIG_SPL_RELOC_MALLOC_SIZE);
|
|
|
|
#ifdef CONFIG_SPL_NAND_BOOT
|
|
nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
#ifdef CONFIG_SPL_MMC_BOOT
|
|
mmc_initialize(bd);
|
|
mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
#ifdef CONFIG_SPL_SPI_BOOT
|
|
spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
|
(uchar *)CONFIG_ENV_ADDR);
|
|
#endif
|
|
|
|
gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
|
|
gd->env_valid = 1;
|
|
|
|
i2c_init_all();
|
|
|
|
gd->ram_size = initdram(0);
|
|
|
|
#ifdef CONFIG_SPL_MMC_BOOT
|
|
mmc_boot();
|
|
#elif defined(CONFIG_SPL_SPI_BOOT)
|
|
spi_boot();
|
|
#elif defined(CONFIG_SPL_NAND_BOOT)
|
|
nand_boot();
|
|
#endif
|
|
}
|