u-boot/board/prodrive/p3mx/sdram_init.c
Wolfgang Denk 3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00

418 lines
12 KiB
C

/*
* (C) Copyright 2001
* Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*************************************************************************
* adaption for the Marvell DB64460 Board
* Ingo Assmus (ingo.assmus@keymile.com)
*************************************************************************/
/* sdram_init.c - automatic memory sizing */
#include <common.h>
#include <74xx_7xx.h>
#include "../../Marvell/include/memory.h"
#include "../../Marvell/include/pci.h"
#include "../../Marvell/include/mv_gen_reg.h"
#include <net.h>
#include "eth.h"
#include "mpsc.h"
#include "../../Marvell/common/i2c.h"
#include "64460.h"
#include "mv_regs.h"
DECLARE_GLOBAL_DATA_PTR;
#undef DEBUG
#define MAP_PCI
#ifdef DEBUG
#define DP(x) x
#else
#define DP(x)
#endif
int set_dfcdlInit (void); /* setup delay line of Mv64460 */
int mvDmaIsChannelActive (int);
int mvDmaSetMemorySpace (ulong, ulong, ulong, ulong, ulong);
int mvDmaTransfer (int, ulong, ulong, ulong, ulong);
#define D_CACHE_FLUSH_LINE(addr, offset) \
{ \
__asm__ __volatile__ ("dcbf %0,%1" : : "r" (addr), "r" (offset)); \
}
int memory_map_bank (unsigned int bankNo,
unsigned int bankBase, unsigned int bankLength)
{
#if defined (MAP_PCI) && defined (CONFIG_PCI)
PCI_HOST host;
#endif
#ifdef DEBUG
if (bankLength > 0) {
printf ("mapping bank %d at %08x - %08x\n",
bankNo, bankBase, bankBase + bankLength - 1);
} else {
printf ("unmapping bank %d\n", bankNo);
}
#endif
memoryMapBank (bankNo, bankBase, bankLength);
#if defined (MAP_PCI) && defined (CONFIG_PCI)
for (host = PCI_HOST0; host <= PCI_HOST1; host++) {
const int features =
PREFETCH_ENABLE |
DELAYED_READ_ENABLE |
AGGRESSIVE_PREFETCH |
READ_LINE_AGGRESSIVE_PREFETCH |
READ_MULTI_AGGRESSIVE_PREFETCH |
MAX_BURST_4 | PCI_NO_SWAP;
pciMapMemoryBank (host, bankNo, bankBase, bankLength);
pciSetRegionSnoopMode (host, bankNo, PCI_SNOOP_WB, bankBase,
bankLength);
pciSetRegionFeatures (host, bankNo, features, bankBase,
bankLength);
}
#endif
return 0;
}
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
long int dram_size (long int *base, long int maxsize)
{
volatile long int *addr, *b = base;
long int cnt, val, save1, save2;
#define STARTVAL (1<<20) /* start test at 1M */
for (cnt = STARTVAL / sizeof (long); cnt < maxsize / sizeof (long);
cnt <<= 1) {
addr = base + cnt; /* pointer arith! */
save1 = *addr; /* save contents of addr */
save2 = *b; /* save contents of base */
*addr = cnt; /* write cnt to addr */
*b = 0; /* put null at base */
/* check at base address */
if ((*b) != 0) {
*addr = save1; /* restore *addr */
*b = save2; /* restore *b */
return (0);
}
val = *addr; /* read *addr */
val = *addr; /* read *addr */
*addr = save1;
*b = save2;
if (val != cnt) {
DP (printf
("Found %08x at Address %08x (failure)\n",
(unsigned int) val, (unsigned int) addr));
/* fix boundary condition.. STARTVAL means zero */
if (cnt == STARTVAL / sizeof (long))
cnt = 0;
return (cnt * sizeof (long));
}
}
return maxsize;
}
#define SDRAM_NORMAL 0x0
#define SDRAM_PRECHARGE_ALL 0x1
#define SDRAM_REFRESH_ALL 0x2
#define SDRAM_MODE_REG_SETUP 0x3
#define SDRAM_XTEN_MODE_REG_SETUP 0x4
#define SDRAM_NOP 0x5
#define SDRAM_SELF_REFRESH 0x7
phys_size_t initdram (int board_type)
{
int tmp;
int start;
ulong size;
ulong memSpaceAttr;
ulong dest;
/* first disable all banks */
memory_map_bank(0, 0, 0);
memory_map_bank(1, 0, 0);
memory_map_bank(2, 0, 0);
memory_map_bank(3, 0, 0);
/* calibrate delay lines */
set_dfcdlInit();
GT_REG_WRITE(MV64460_SDRAM_OPERATION, SDRAM_NOP); /* 0x1418 */
do {
tmp = GTREGREAD(MV64460_SDRAM_OPERATION);
} while(tmp != 0x0);
/* SDRAM controller configuration */
#ifdef CONFIG_MV64460_ECC
GT_REG_WRITE(MV64460_SDRAM_CONFIG, 0x58201400); /* 0x1400 */
#else
GT_REG_WRITE(MV64460_SDRAM_CONFIG, 0x58200400); /* 0x1400 */
#endif
GT_REG_WRITE(MV64460_D_UNIT_CONTROL_LOW, 0xC3000540); /* 0x1404 */
GT_REG_WRITE(MV64460_D_UNIT_CONTROL_HIGH, 0x0300F777); /* 0x1424 */
GT_REG_WRITE(MV64460_SDRAM_TIMING_CONTROL_LOW, 0x01712220); /* 0x1408 */
GT_REG_WRITE(MV64460_SDRAM_TIMING_CONTROL_HIGH, 0x0000005D); /* 0x140C */
GT_REG_WRITE(MV64460_SDRAM_ADDR_CONTROL, 0x00000012); /* 0x1410 */
GT_REG_WRITE(MV64460_SDRAM_OPEN_PAGES_CONTROL, 0x00000001); /* 0x1414 */
/* SDRAM drive strength */
GT_REG_WRITE(MV64460_SDRAM_ADDR_CTRL_PADS_CALIBRATION, 0x80000000); /* 0x14C0 */
GT_REG_WRITE(MV64460_SDRAM_ADDR_CTRL_PADS_CALIBRATION, 0x80000008); /* 0x14C0 */
GT_REG_WRITE(MV64460_SDRAM_DATA_PADS_CALIBRATION, 0x80000000); /* 0x14C4 */
GT_REG_WRITE(MV64460_SDRAM_DATA_PADS_CALIBRATION, 0x80000008); /* 0x14C4 */
/* setup SDRAM device registers */
/* precharge all */
GT_REG_WRITE(MV64460_SDRAM_OPERATION, SDRAM_PRECHARGE_ALL); /* 0x1418 */
do {
tmp = GTREGREAD(MV64460_SDRAM_OPERATION);
} while(tmp != 0x0);
/* enable DLL */
GT_REG_WRITE(MV64460_EXTENDED_DRAM_MODE, 0x00000000); /* 0x1420 */
GT_REG_WRITE(MV64460_SDRAM_OPERATION, SDRAM_XTEN_MODE_REG_SETUP); /* 0x1418 */
do {
tmp = GTREGREAD(MV64460_SDRAM_OPERATION);
} while(tmp != 0x0);
/* reset DLL */
GT_REG_WRITE(MV64460_SDRAM_MODE, 0x00000132); /* 0x141C */
GT_REG_WRITE(MV64460_SDRAM_OPERATION, SDRAM_MODE_REG_SETUP); /* 0x1418 */
do {
tmp = GTREGREAD(MV64460_SDRAM_OPERATION);
} while(tmp != 0x0);
/* precharge all */
GT_REG_WRITE(MV64460_SDRAM_OPERATION, SDRAM_PRECHARGE_ALL); /* 0x1418 */
do {
tmp = GTREGREAD(MV64460_SDRAM_OPERATION);
} while(tmp != 0x0);
/* wait for 2 auto refresh commands */
udelay(20);
/* un-reset DLL */
GT_REG_WRITE(MV64460_SDRAM_MODE, 0x00000032); /* 0x141C */
GT_REG_WRITE(MV64460_SDRAM_OPERATION, SDRAM_MODE_REG_SETUP); /* 0x1418 */
do {
tmp = GTREGREAD(MV64460_SDRAM_OPERATION);
} while(tmp != 0x0);
/* wait 200 cycles */
udelay(2); /* FIXME make this dynamic for the system clock */
/* SDRAM init done */
memory_map_bank(0, CONFIG_SYS_SDRAM_BASE, (256 << 20));
#ifdef CONFIG_SYS_SDRAM1_BASE
memory_map_bank(1, CONFIG_SYS_SDRAM1_BASE, (256 << 20));
#endif
/* DUNIT_MMASK: enable SnoopHitEn bit to avoid errata CPU-#4
*/
tmp = GTREGREAD(MV64460_D_UNIT_MMASK); /* 0x14B0 */
GT_REG_WRITE(MV64460_D_UNIT_MMASK, tmp | 0x2);
start = (0 << 20);
#ifdef CONFIG_P3M750
size = (512 << 20);
#elif defined (CONFIG_P3M7448)
size = (128 << 20);
#endif
#ifdef CONFIG_MV64460_ECC
memSpaceAttr = ((~(BIT0 << 0)) & 0xf) << 8;
mvDmaSetMemorySpace (0, 0, memSpaceAttr, start, size);
for (dest = start; dest < start + size; dest += _8M) {
mvDmaTransfer (0, start, dest, _8M,
BIT8 /*DMA_DTL_128BYTES */ |
BIT3 /*DMA_HOLD_SOURCE_ADDR */ |
BIT11 /*DMA_BLOCK_TRANSFER_MODE */ );
while (mvDmaIsChannelActive (0));
}
#endif
return (size);
}
void board_add_ram_info(int use_default)
{
u32 val;
puts(" (CL=");
switch ((GTREGREAD(MV64460_SDRAM_MODE) >> 4) & 0x7) {
case 0x2:
puts("2");
break;
case 0x3:
puts("3");
break;
case 0x5:
puts("1.5");
break;
case 0x6:
puts("2.5");
break;
}
val = GTREGREAD(MV64460_SDRAM_CONFIG);
puts(", ECC ");
if (val & 0x00001000)
puts("enabled)");
else
puts("not enabled)");
}
/*
* mvDmaIsChannelActive - Check if IDMA channel is active
*
* channel = IDMA channel number from 0 to 7
*/
int mvDmaIsChannelActive (int channel)
{
ulong data;
data = GTREGREAD (MV64460_DMA_CHANNEL0_CONTROL + 4 * channel);
if (data & BIT14) /* activity status */
return 1;
return 0;
}
/*
* mvDmaSetMemorySpace - Set a DMA memory window for the DMA's address decoding
* map.
*
* memSpace = IDMA memory window number from 0 to 7
* trg_if = Target interface:
* 0x0 DRAM
* 0x1 Device Bus
* 0x2 Integrated SDRAM (or CPU bus 60x only)
* 0x3 PCI0
* 0x4 PCI1
* attr = IDMA attributes (see MV datasheet)
* base_addr = Sets up memory window for transfers
*
*/
int mvDmaSetMemorySpace (ulong memSpace,
ulong trg_if,
ulong attr, ulong base_addr, ulong size)
{
ulong temp;
/* The base address must be aligned to the size. */
if (base_addr % size != 0)
return 0;
if (size >= 0x10000) { /* 64K */
size &= 0xffff0000;
base_addr = (base_addr & 0xffff0000);
/* Set the new attributes */
GT_REG_WRITE (MV64460_DMA_BASE_ADDR_REG0 + memSpace * 8,
(base_addr | trg_if | attr));
GT_REG_WRITE ((MV64460_DMA_SIZE_REG0 + memSpace * 8),
(size - 1) & 0xffff0000);
temp = GTREGREAD (MV64460_DMA_BASE_ADDR_ENABLE_REG);
GT_REG_WRITE (DMA_BASE_ADDR_ENABLE_REG,
(temp & ~(BIT0 << memSpace)));
return 1;
}
return 0;
}
/*
* mvDmaTransfer - Transfer data from src_addr to dst_addr on one of the 4
* DMA channels.
*
* channel = IDMA channel number from 0 to 3
* destAddr = Destination address
* sourceAddr = Source address
* size = Size in bytes
* command = See MV datasheet
*
*/
int mvDmaTransfer (int channel, ulong sourceAddr,
ulong destAddr, ulong size, ulong command)
{
ulong engOffReg = 0; /* Engine Offset Register */
if (size > 0xffff)
command = command | BIT31; /* DMA_16M_DESCRIPTOR_MODE */
command = command | ((command >> 6) & 0x7);
engOffReg = channel * 4;
GT_REG_WRITE (MV64460_DMA_CHANNEL0_BYTE_COUNT + engOffReg, size);
GT_REG_WRITE (MV64460_DMA_CHANNEL0_SOURCE_ADDR + engOffReg, sourceAddr);
GT_REG_WRITE (MV64460_DMA_CHANNEL0_DESTINATION_ADDR + engOffReg, destAddr);
command = command |
BIT12 | /* DMA_CHANNEL_ENABLE */
BIT9; /* DMA_NON_CHAIN_MODE */
/* Activate DMA channel By writting to mvDmaControlRegister */
GT_REG_WRITE (MV64460_DMA_CHANNEL0_CONTROL + engOffReg, command);
return 1;
}
/****************************************************************************************
* SDRAM INIT *
* This procedure detect all Sdram types: 64, 128, 256, 512 Mbit, 1Gbit and 2Gb *
* This procedure fits only the Atlantis *
* *
***************************************************************************************/
/****************************************************************************************
* DFCDL initialize MV643xx Design Considerations *
* *
***************************************************************************************/
int set_dfcdlInit (void)
{
int i;
/* Values from MV64460 User Manual */
unsigned int dfcdl_tbl[] = { 0x00000000, 0x00000001, 0x00000042, 0x00000083,
0x000000c4, 0x00000105, 0x00000146, 0x00000187,
0x000001c8, 0x00000209, 0x0000024a, 0x0000028b,
0x000002cc, 0x0000030d, 0x0000034e, 0x0000038f,
0x000003d0, 0x00000411, 0x00000452, 0x00000493,
0x000004d4, 0x00000515, 0x00000556, 0x00000597,
0x000005d8, 0x00000619, 0x0000065a, 0x0000069b,
0x000006dc, 0x0000071d, 0x0000075e, 0x0000079f,
0x000007e0, 0x00000821, 0x00000862, 0x000008a3,
0x000008e4, 0x00000925, 0x00000966, 0x000009a7,
0x000009e8, 0x00000a29, 0x00000a6a, 0x00000aab,
0x00000aec, 0x00000b2d, 0x00000b6e, 0x00000baf,
0x00000bf0, 0x00000c31, 0x00000c72, 0x00000cb3,
0x00000cf4, 0x00000d35, 0x00000d76, 0x00000db7,
0x00000df8, 0x00000e39, 0x00000e7a, 0x00000ebb,
0x00000efc, 0x00000f3d, 0x00000f7e, 0x00000fbf };
for (i = 0; i < 64; i++)
GT_REG_WRITE (SRAM_DATA0, dfcdl_tbl[i]);
GT_REG_WRITE (DFCDL_CONFIG0, 0x00300000); /* enable dynamic delay line updating */
return (0);
}