u-boot/board/davinci/da8xxevm/da850evm.c
Christian Riesch 3864cb2133 da850evm: Use clrbits function with correct endianess
The current code uses clrbits_be32 which is incorrect since we are on
a little endian machine here. This patch fixes this issue and also removes
some unnecessary code: Reading the current GPIO bank state is not required
if we are using the SET and CLEAR GPIO registers for setting/clearing
bits.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Cc: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
2013-07-26 16:39:10 -04:00

494 lines
12 KiB
C

/*
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
*
* Based on da830evm.c. Original Copyrights follow:
*
* Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <net.h>
#include <netdev.h>
#include <spi.h>
#include <spi_flash.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emif_defs.h>
#include <asm/arch/emac_defs.h>
#include <asm/arch/pinmux_defs.h>
#include <asm/io.h>
#include <asm/arch/davinci_misc.h>
#include <asm/errno.h>
#include <hwconfig.h>
#ifdef CONFIG_DAVINCI_MMC
#include <mmc.h>
#include <asm/arch/sdmmc_defs.h>
#endif
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_DRIVER_TI_EMAC
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
#define HAS_RMII 1
#else
#define HAS_RMII 0
#endif
#endif /* CONFIG_DRIVER_TI_EMAC */
#define CFG_MAC_ADDR_SPI_BUS 0
#define CFG_MAC_ADDR_SPI_CS 0
#define CFG_MAC_ADDR_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CFG_MAC_ADDR_SPI_MODE SPI_MODE_3
#define CFG_MAC_ADDR_OFFSET (flash->size - SZ_64K)
#ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
static int get_mac_addr(u8 *addr)
{
struct spi_flash *flash;
int ret;
flash = spi_flash_probe(CFG_MAC_ADDR_SPI_BUS, CFG_MAC_ADDR_SPI_CS,
CFG_MAC_ADDR_SPI_MAX_HZ, CFG_MAC_ADDR_SPI_MODE);
if (!flash) {
printf("Error - unable to probe SPI flash.\n");
return -1;
}
ret = spi_flash_read(flash, CFG_MAC_ADDR_OFFSET, 6, addr);
if (ret) {
printf("Error - unable to read MAC address from SPI flash.\n");
return -1;
}
return ret;
}
#endif
void dsp_lpsc_on(unsigned domain, unsigned int id)
{
dv_reg_p mdstat, mdctl, ptstat, ptcmd;
struct davinci_psc_regs *psc_regs;
psc_regs = davinci_psc0_regs;
mdstat = &psc_regs->psc0.mdstat[id];
mdctl = &psc_regs->psc0.mdctl[id];
ptstat = &psc_regs->ptstat;
ptcmd = &psc_regs->ptcmd;
while (*ptstat & (0x1 << domain))
;
if ((*mdstat & 0x1f) == 0x03)
return; /* Already on and enabled */
*mdctl |= 0x03;
*ptcmd = 0x1 << domain;
while (*ptstat & (0x1 << domain))
;
while ((*mdstat & 0x1f) != 0x03)
; /* Probably an overkill... */
}
static void dspwake(void)
{
unsigned *resetvect = (unsigned *)DAVINCI_L3CBARAM_BASE;
u32 val;
/* if the device is ARM only, return */
if ((readl(CHIP_REV_ID_REG) & 0x3f) == 0x10)
return;
if (hwconfig_subarg_cmp_f("dsp", "wake", "no", NULL))
return;
*resetvect++ = 0x1E000; /* DSP Idle */
/* clear out the next 10 words as NOP */
memset(resetvect, 0, sizeof(unsigned) *10);
/* setup the DSP reset vector */
writel(DAVINCI_L3CBARAM_BASE, HOST1CFG);
dsp_lpsc_on(1, DAVINCI_LPSC_GEM);
val = readl(PSC0_MDCTL + (15 * 4));
val |= 0x100;
writel(val, (PSC0_MDCTL + (15 * 4)));
}
int misc_init_r(void)
{
dspwake();
#if defined(CONFIG_MAC_ADDR_IN_SPIFLASH) || defined(CONFIG_MAC_ADDR_IN_EEPROM)
uchar env_enetaddr[6];
int enetaddr_found;
enetaddr_found = eth_getenv_enetaddr("ethaddr", env_enetaddr);
#ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
int spi_mac_read;
uchar buff[6];
spi_mac_read = get_mac_addr(buff);
/*
* MAC address not present in the environment
* try and read the MAC address from SPI flash
* and set it.
*/
if (!enetaddr_found) {
if (!spi_mac_read) {
if (is_valid_ether_addr(buff)) {
if (eth_setenv_enetaddr("ethaddr", buff)) {
printf("Warning: Failed to "
"set MAC address from SPI flash\n");
}
} else {
printf("Warning: Invalid "
"MAC address read from SPI flash\n");
}
}
} else {
/*
* MAC address present in environment compare it with
* the MAC address in SPI flash and warn on mismatch
*/
if (!spi_mac_read && is_valid_ether_addr(buff) &&
memcmp(env_enetaddr, buff, 6))
printf("Warning: MAC address in SPI flash don't match "
"with the MAC address in the environment\n");
printf("Default using MAC address from environment\n");
}
#endif
uint8_t enetaddr[8];
int eeprom_mac_read;
/* Read Ethernet MAC address from EEPROM */
eeprom_mac_read = dvevm_read_mac_address(enetaddr);
/*
* MAC address not present in the environment
* try and read the MAC address from EEPROM flash
* and set it.
*/
if (!enetaddr_found) {
if (eeprom_mac_read)
/* Set Ethernet MAC address from EEPROM */
davinci_sync_env_enetaddr(enetaddr);
} else {
/*
* MAC address present in environment compare it with
* the MAC address in EEPROM and warn on mismatch
*/
if (eeprom_mac_read && memcmp(enetaddr, env_enetaddr, 6))
printf("Warning: MAC address in EEPROM don't match "
"with the MAC address in the environment\n");
printf("Default using MAC address from environment\n");
}
#endif
return 0;
}
#ifdef CONFIG_DAVINCI_MMC
static struct davinci_mmc mmc_sd0 = {
.reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
.host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
.version = MMC_CTLR_VERSION_2,
};
int board_mmc_init(bd_t *bis)
{
mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID);
/* Add slot-0 to mmc subsystem */
return davinci_mmc_init(bis, &mmc_sd0);
}
#endif
static const struct pinmux_config gpio_pins[] = {
#ifdef CONFIG_USE_NOR
/* GP0[11] is required for NOR to work on Rev 3 EVMs */
{ pinmux(0), 8, 4 }, /* GP0[11] */
#endif
#ifdef CONFIG_DAVINCI_MMC
/* GP0[11] is required for SD to work on Rev 3 EVMs */
{ pinmux(0), 8, 4 }, /* GP0[11] */
#endif
};
const struct pinmux_resource pinmuxes[] = {
#ifdef CONFIG_DRIVER_TI_EMAC
PINMUX_ITEM(emac_pins_mdio),
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
PINMUX_ITEM(emac_pins_rmii),
#else
PINMUX_ITEM(emac_pins_mii),
#endif
#endif
#ifdef CONFIG_SPI_FLASH
PINMUX_ITEM(spi1_pins_base),
PINMUX_ITEM(spi1_pins_scs0),
#endif
PINMUX_ITEM(uart2_pins_txrx),
PINMUX_ITEM(uart2_pins_rtscts),
PINMUX_ITEM(i2c0_pins),
#ifdef CONFIG_NAND_DAVINCI
PINMUX_ITEM(emifa_pins_cs3),
PINMUX_ITEM(emifa_pins_cs4),
PINMUX_ITEM(emifa_pins_nand),
#elif defined(CONFIG_USE_NOR)
PINMUX_ITEM(emifa_pins_cs2),
PINMUX_ITEM(emifa_pins_nor),
#endif
PINMUX_ITEM(gpio_pins),
#ifdef CONFIG_DAVINCI_MMC
PINMUX_ITEM(mmc0_pins),
#endif
};
const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
const struct lpsc_resource lpsc[] = {
{ DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
{ DAVINCI_LPSC_SPI1 }, /* Serial Flash */
{ DAVINCI_LPSC_EMAC }, /* image download */
{ DAVINCI_LPSC_UART2 }, /* console */
{ DAVINCI_LPSC_GPIO },
#ifdef CONFIG_DAVINCI_MMC
{ DAVINCI_LPSC_MMC_SD },
#endif
};
const int lpsc_size = ARRAY_SIZE(lpsc);
#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
#define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000
#endif
#define REV_AM18X_EVM 0x100
/*
* get_board_rev() - setup to pass kernel board revision information
* Returns:
* bit[0-3] Maximum cpu clock rate supported by onboard SoC
* 0000b - 300 MHz
* 0001b - 372 MHz
* 0010b - 408 MHz
* 0011b - 456 MHz
*/
u32 get_board_rev(void)
{
char *s;
u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
u32 rev = 0;
s = getenv("maxcpuclk");
if (s)
maxcpuclk = simple_strtoul(s, NULL, 10);
if (maxcpuclk >= 456000000)
rev = 3;
else if (maxcpuclk >= 408000000)
rev = 2;
else if (maxcpuclk >= 372000000)
rev = 1;
#ifdef CONFIG_DA850_AM18X_EVM
rev |= REV_AM18X_EVM;
#endif
return rev;
}
int board_early_init_f(void)
{
/*
* Power on required peripherals
* ARM does not have access by default to PSC0 and PSC1
* assuming here that the DSP bootloader has set the IOPU
* such that PSC access is available to ARM
*/
if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
return 1;
return 0;
}
int board_init(void)
{
#ifndef CONFIG_USE_IRQ
irq_init();
#endif
#ifdef CONFIG_NAND_DAVINCI
/*
* NAND CS setup - cycle counts based on da850evm NAND timings in the
* Linux kernel @ 25MHz EMIFA
*/
writel((DAVINCI_ABCR_WSETUP(2) |
DAVINCI_ABCR_WSTROBE(2) |
DAVINCI_ABCR_WHOLD(1) |
DAVINCI_ABCR_RSETUP(1) |
DAVINCI_ABCR_RSTROBE(4) |
DAVINCI_ABCR_RHOLD(0) |
DAVINCI_ABCR_TA(1) |
DAVINCI_ABCR_ASIZE_8BIT),
&davinci_emif_regs->ab2cr); /* CS3 */
#endif
/* arch number of the board */
gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;
/* address of boot parameters */
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
/* setup the SUSPSRC for ARM to control emulation suspend */
writel(readl(&davinci_syscfg_regs->suspsrc) &
~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
DAVINCI_SYSCFG_SUSPSRC_UART2),
&davinci_syscfg_regs->suspsrc);
/* configure pinmux settings */
if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
return 1;
#ifdef CONFIG_USE_NOR
/* Set the GPIO direction as output */
clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
/* Set the output as low */
writel(0x01 << 11, GPIO_BANK0_REG_CLR_ADDR);
#endif
#ifdef CONFIG_DAVINCI_MMC
/* Set the GPIO direction as output */
clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
/* Set the output as high */
writel(0x01 << 11, GPIO_BANK0_REG_SET_ADDR);
#endif
#ifdef CONFIG_DRIVER_TI_EMAC
davinci_emac_mii_mode_sel(HAS_RMII);
#endif /* CONFIG_DRIVER_TI_EMAC */
/* enable the console UART */
writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
DAVINCI_UART_PWREMU_MGMT_UTRST),
&davinci_uart2_ctrl_regs->pwremu_mgmt);
return 0;
}
#ifdef CONFIG_DRIVER_TI_EMAC
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
/**
* rmii_hw_init
*
* DA850/OMAP-L138 EVM can interface to a daughter card for
* additional features. This card has an I2C GPIO Expander TCA6416
* to select the required functions like camera, RMII Ethernet,
* character LCD, video.
*
* Initialization of the expander involves configuring the
* polarity and direction of the ports. P07-P05 are used here.
* These ports are connected to a Mux chip which enables only one
* functionality at a time.
*
* For RMII phy to respond, the MII MDIO clock has to be disabled
* since both the PHY devices have address as zero. The MII MDIO
* clock is controlled via GPIO2[6].
*
* This code is valid for Beta version of the hardware
*/
int rmii_hw_init(void)
{
const struct pinmux_config gpio_pins[] = {
{ pinmux(6), 8, 1 }
};
u_int8_t buf[2];
unsigned int temp;
int ret;
/* PinMux for GPIO */
if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
return 1;
/* I2C Exapnder configuration */
/* Set polarity to non-inverted */
buf[0] = 0x0;
buf[1] = 0x0;
ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 4, 1, buf, 2);
if (ret) {
printf("\nExpander @ 0x%02x write FAILED!!!\n",
CONFIG_SYS_I2C_EXPANDER_ADDR);
return ret;
}
/* Configure P07-P05 as outputs */
buf[0] = 0x1f;
buf[1] = 0xff;
ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 6, 1, buf, 2);
if (ret) {
printf("\nExpander @ 0x%02x write FAILED!!!\n",
CONFIG_SYS_I2C_EXPANDER_ADDR);
}
/* For Ethernet RMII selection
* P07(SelA)=0
* P06(SelB)=1
* P05(SelC)=1
*/
if (i2c_read(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
printf("\nExpander @ 0x%02x read FAILED!!!\n",
CONFIG_SYS_I2C_EXPANDER_ADDR);
}
buf[0] &= 0x1f;
buf[0] |= (0 << 7) | (1 << 6) | (1 << 5);
if (i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
printf("\nExpander @ 0x%02x write FAILED!!!\n",
CONFIG_SYS_I2C_EXPANDER_ADDR);
}
/* Set the output as high */
temp = REG(GPIO_BANK2_REG_SET_ADDR);
temp |= (0x01 << 6);
REG(GPIO_BANK2_REG_SET_ADDR) = temp;
/* Set the GPIO direction as output */
temp = REG(GPIO_BANK2_REG_DIR_ADDR);
temp &= ~(0x01 << 6);
REG(GPIO_BANK2_REG_DIR_ADDR) = temp;
return 0;
}
#endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */
/*
* Initializes on-board ethernet controllers.
*/
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
/* Select RMII fucntion through the expander */
if (rmii_hw_init())
printf("RMII hardware init failed!!!\n");
#endif
if (!davinci_emac_initialize()) {
printf("Error: Ethernet init failed!\n");
return -1;
}
return 0;
}
#endif /* CONFIG_DRIVER_TI_EMAC */