mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-09-30 11:22:09 +00:00
a6924c95d1
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code. The set_wdog_reset() function is not necessary as this is handled by the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property being set. Signed-off-by: Peng Fan <peng.fan@nxp.com>
129 lines
2.7 KiB
C
129 lines
2.7 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* Copyright 2022 Toradex
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx8mp_pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm-generic/gpio.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/mach-imx/gpio.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <errno.h>
|
|
#include <env.h>
|
|
#include <init.h>
|
|
#include <linux/delay.h>
|
|
#include <micrel.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
|
|
#include "../common/tdx-cfg-block.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
|
|
|
|
/* Verdin UART_3, Console/Debug UART */
|
|
static const iomux_v3_cfg_t uart_pads[] = {
|
|
MX8MP_PAD_UART3_RXD__UART3_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX8MP_PAD_UART3_TXD__UART3_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
|
|
|
|
init_uart_clk(2);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void setup_fec(void)
|
|
{
|
|
struct iomuxc_gpr_base_regs *gpr =
|
|
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
|
|
|
|
/* Enable RGMII TX clk output */
|
|
setbits_le32(&gpr->gpr[1], BIT(22));
|
|
}
|
|
|
|
static int setup_eqos(void)
|
|
{
|
|
struct iomuxc_gpr_base_regs *gpr =
|
|
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
|
|
|
|
/* set INTF as RGMII, enable RGMII TXC clock */
|
|
clrsetbits_le32(&gpr->gpr[1],
|
|
IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK, BIT(16));
|
|
setbits_le32(&gpr->gpr[1], BIT(19) | BIT(21));
|
|
|
|
return set_clk_eqos(ENET_125MHZ);
|
|
}
|
|
|
|
#if IS_ENABLED(CONFIG_NET)
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (IS_ENABLED(CONFIG_FEC_MXC))
|
|
setup_fec();
|
|
|
|
if (IS_ENABLED(CONFIG_DWC_ETH_QOS))
|
|
ret = setup_eqos();
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void select_dt_from_module_version(void)
|
|
{
|
|
char variant[32];
|
|
char *env_variant = env_get("variant");
|
|
int is_wifi = 0;
|
|
|
|
if (IS_ENABLED(CONFIG_TDX_CFG_BLOCK)) {
|
|
/*
|
|
* If we have a valid config block and it says we are a module with
|
|
* Wi-Fi/Bluetooth make sure we use the -wifi device tree.
|
|
*/
|
|
is_wifi = (tdx_hw_tag.prodid == VERDIN_IMX8MPQ_WIFI_BT_IT) ||
|
|
(tdx_hw_tag.prodid == VERDIN_IMX8MPQ_2GB_WIFI_BT_IT) ||
|
|
(tdx_hw_tag.prodid == VERDIN_IMX8MPQ_8GB_WIFI_BT);
|
|
}
|
|
|
|
if (is_wifi)
|
|
strlcpy(&variant[0], "wifi", sizeof(variant));
|
|
else
|
|
strlcpy(&variant[0], "nonwifi", sizeof(variant));
|
|
|
|
if (strcmp(variant, env_variant)) {
|
|
printf("Setting variant to %s\n", variant);
|
|
env_set("variant", variant);
|
|
|
|
if (IS_ENABLED(CONFIG_ENV_IS_NOWHERE))
|
|
env_save();
|
|
}
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
select_dt_from_module_version();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if IS_ENABLED(CONFIG_OF_LIBFDT) && IS_ENABLED(CONFIG_OF_BOARD_SETUP)
|
|
int ft_board_setup(void *blob, struct bd_info *bd)
|
|
{
|
|
return 0;
|
|
}
|
|
#endif
|