mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 05:42:58 +00:00
b68d57c310
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
223 lines
8.1 KiB
Text
223 lines
8.1 KiB
Text
DENX M28EVK
|
|
===========
|
|
|
|
This document describes the DENX M28/M28EVK U-Boot port. This document mostly
|
|
covers topics related to making the module/board bootable.
|
|
|
|
Terminology
|
|
-----------
|
|
|
|
The dollar symbol ($) introduces a snipped of shell code. This shall be typed
|
|
into the unix command prompt in U-Boot source code root directory.
|
|
|
|
The (=>) introduces a snipped of code that should by typed into U-Boot command
|
|
prompt.
|
|
|
|
Contents
|
|
--------
|
|
|
|
0) Files of the M28/M28EVK port
|
|
1) Prerequisites
|
|
2) Compiling U-Boot for M28
|
|
3) Installation of U-Boot for M28EVK to SD card
|
|
4) Installation of U-Boot for M28 to NAND flash
|
|
|
|
0) Files of the M28/M28EVK port
|
|
-------------------------------
|
|
|
|
arch/arm/cpu/arm926ejs/mx28/ - The CPU support code for the Freescale i.MX28
|
|
arch/arm/include/asm/arch-mx28/ - Header files for the Freescale i.MX28
|
|
board/denx/m28evk/ - M28EVK board specific files
|
|
include/configs/m28evk.h - M28EVK configuration file
|
|
|
|
1) Prerequisites
|
|
----------------
|
|
|
|
To make the M28 module or the M28 module or M28EVK board bootable, some tools
|
|
are necessary. The first one is the "elftosb" tool distributed by Freescale
|
|
Semiconductor. The other tool is the "mxsboot" tool found in U-Boot source tree.
|
|
|
|
Firstly, obtain the elftosb archive from the following location:
|
|
|
|
http://foss.doredevelopment.dk/mirrors/imx/elftosb-10.12.01.tar.gz
|
|
|
|
We use a $VER variable here to denote the current version. At the time of
|
|
writing of this document, that is "10.12.01". To obtain the file from command
|
|
line, use:
|
|
|
|
$ VER="10.12.01"
|
|
$ wget http://foss.doredevelopment.dk/mirrors/imx/elftosb-${VER}.tar.gz
|
|
|
|
Extract the file:
|
|
|
|
$ tar xzf elftosb-${VER}.tar.gz
|
|
|
|
Compile the file. We need to manually tell the linker to use also libm:
|
|
|
|
$ cd elftosb-${VER}/
|
|
$ make LIBS="-lstdc++ -lm" elftosb
|
|
|
|
Optionally, remove debugging symbols from elftosb:
|
|
|
|
$ strip bld/linux/elftosb
|
|
|
|
Finally, install the "elftosb" binary. The "install" target is missing, so just
|
|
copy the binary by hand:
|
|
|
|
$ sudo cp bld/linux/elftosb /usr/local/bin/
|
|
|
|
Make sure the "elftosb" binary can be found in your $PATH, in this case this
|
|
means "/usr/local/bin/" has to be in your $PATH.
|
|
|
|
2) Compiling U-Boot for M28
|
|
---------------------------
|
|
|
|
Compiling the U-Boot for M28 is straightforward and done as compiling U-Boot
|
|
for any other ARM device. For cross-compiler setup, please refer to ELDK5.0
|
|
documentation. First, clean up the source code:
|
|
|
|
$ make mrproper
|
|
|
|
Next, configure U-Boot for M28EVK:
|
|
|
|
$ make m28evk_config
|
|
|
|
Lastly, compile U-Boot and prepare a "BootStream". The "BootStream" is a special
|
|
type of file, which the i.MX28 CPU can boot. This is handled by the following
|
|
command:
|
|
|
|
$ make u-boot.sb
|
|
|
|
HINT: To speed-up the build process, you can add -j<N>, where N is number of
|
|
compiler instances that'll run in parallel.
|
|
|
|
The code produces "u-boot.sb" file. This file needs to be augmented with a
|
|
proper header to allow successful boot from SD or NAND. Adding the header is
|
|
discussed in the following chapters.
|
|
|
|
3) Installation of U-Boot for M28EVK to SD card
|
|
-----------------------------------------------
|
|
|
|
To boot an M28 from SD, set the boot mode DIP switches according to i.MX28
|
|
manual chapter 12.2.1 (Table 12-2), PORT=SSP0, SD/MMC master on SSP0, 3.3V.
|
|
|
|
An SD card the i.MX28 CPU can use to boot U-Boot must contain a DOS partition
|
|
table, which in turn carries a partition of special type and which contains a
|
|
special header. The rest of partitions in the DOS partition table can be used
|
|
by the user.
|
|
|
|
To prepare such partition, use your favourite partitioning tool. The partition
|
|
must have the following parameters:
|
|
|
|
* Start sector .......... sector 2048
|
|
* Partition size ........ at least 1024 kb
|
|
* Partition type ........ 0x53 (sometimes "OnTrack DM6 Aux3")
|
|
|
|
For example in Linux fdisk, the sequence for a clear card is the following:
|
|
|
|
* o ..................... create a clear partition table
|
|
* n ..................... create new partition
|
|
* p ............. primary partition
|
|
* 1 ............. first partition
|
|
* 2048 .......... first sector is 2048
|
|
* +1M ........... make the partition 1Mb big
|
|
* t 1 ................... change first partition ID
|
|
* 53 ............ change the ID to 0x53 (OnTrack DM6 Aux3)
|
|
* <create other partitions>
|
|
* w ..................... write partition table to disk
|
|
|
|
The partition layout is ready, next the special partition must be filled with
|
|
proper contents. The contents is generated by running the following command (see
|
|
chapter 2)):
|
|
|
|
$ ./tools/mxsboot sd u-boot.sb u-boot.sd
|
|
|
|
The resulting file, "u-boot.sd", shall then be written to the partition. In this
|
|
case, we assume the first partition of the SD card is /dev/mmcblk0p1:
|
|
|
|
$ dd if=u-boot.sd of=/dev/mmcblk0p1
|
|
|
|
Last step is to insert the card into M28EVK and boot.
|
|
|
|
NOTE: If the user needs to adjust the start sector, the "mxsboot" tool contains
|
|
a "-p" switch for that purpose. The "-p" switch takes the sector number as
|
|
an argument.
|
|
|
|
4) Installation of U-Boot for M28 to NAND flash
|
|
-----------------------------------------------
|
|
|
|
To boot an M28 from NAND, set the boot mode DIP switches according to i.MX28
|
|
manual chapter 12.2.1 (Table 12-2), PORT=GPMI, NAND 1.8 V.
|
|
|
|
There are two possibilities when preparing an image writable to NAND flash.
|
|
|
|
I) The NAND wasn't written at all yet or the BCB is broken
|
|
----------------------------------------------------------
|
|
In this case, both BCB (FCB and DBBT) and firmware needs to be
|
|
written to NAND. To generate NAND image containing all these,
|
|
there is a tool called "mxsboot" in the "tools/" directory. The tool
|
|
is invoked on "u-boot.sb" file from chapter 2):
|
|
|
|
$ ./tools/mxsboot nand u-boot.sb u-boot.nand
|
|
|
|
NOTE: The above invokation works for NAND flash with geometry of
|
|
2048b per page, 64b OOB data, 128kb erase size. If your chip
|
|
has a different geometry, please use:
|
|
|
|
-w <size> change page size (default 2048 b)
|
|
-o <size> change oob size (default 64 b)
|
|
-e <size> change erase size (default 131072 b)
|
|
|
|
The geometry information can be obtained from running U-Boot
|
|
on M28 by issuing the "nand info" command.
|
|
|
|
The resulting file, "u-boot.nand" can be written directly to NAND
|
|
from the U-Boot prompt. To simplify the process, the U-Boot default
|
|
environment contains script "update_nand_full" to update the system.
|
|
|
|
This script expects a working TFTP server containing the file
|
|
"u-boot.nand" in it's root directory. This can be changed by
|
|
adjusting the "update_nand_full_filename" varible.
|
|
|
|
To update the system, run the following in U-Boot prompt:
|
|
|
|
=> run update_nand_full
|
|
|
|
In case you would only need to update the bootloader in future,
|
|
see II) below.
|
|
|
|
II) The NAND was already written with a good BCB
|
|
------------------------------------------------
|
|
This part applies after the part I) above was done at least once.
|
|
|
|
If part I) above was done correctly already, there is no need to
|
|
write the FCB and DBBT parts of NAND again. It's possible to upgrade
|
|
only the bootloader image.
|
|
|
|
To simplify the process of firmware update, the U-Boot default
|
|
environment contains script "update_nand_firmware" to update only
|
|
the firmware, without rewriting FCB and DBBT.
|
|
|
|
This script expects a working TFTP server containing the file
|
|
"u-boot.sb" in it's root directory. This can be changed by
|
|
adjusting the "update_nand_firmware_filename" varible.
|
|
|
|
To update the system, run the following in U-Boot prompt:
|
|
|
|
=> run update_nand_firmware
|
|
|
|
III) Special settings for the update scripts
|
|
--------------------------------------------
|
|
There is a slight possibility of the user wanting to adjust the
|
|
STRIDE and COUNT options of the NAND boot. For description of these,
|
|
see i.MX28 manual section 12.12.1.2 and 12.12.1.3.
|
|
|
|
The update scripts take this possibility into account. In case the
|
|
user changes STRIDE by blowing fuses, the user also has to change
|
|
"update_nand_stride" variable. In case the user changes COUNT by
|
|
blowing fuses, the user also has to change "update_nand_count"
|
|
variable for the update scripts to work correctly.
|
|
|
|
In case the user needs to boot a firmware image bigger than 1Mb, the
|
|
user has to adjust the "update_nand_firmware_maxsz" variable for the
|
|
update scripts to work properly.
|