u-boot/include/configs/ge_bx50v3.h
Tom Rini e985eb14ac Convert CONFIG_CMD_ASKENV et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04 18:10:02 -04:00

181 lines
5.1 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2015 Timesys Corporation
* Copyright (C) 2015 General Electric Company
* Copyright (C) 2014 Advantech
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Configuration settings for the GE MX6Q Bx50v3 boards.
*/
#ifndef __GE_BX50V3_CONFIG_H
#define __GE_BX50V3_CONFIG_H
#include <asm/arch/imx-regs.h>
#include <asm/mach-imx/gpio.h>
#define CONFIG_BOARD_NAME "General Electric Bx50v3"
#include "mx6_common.h"
#include <linux/sizes.h>
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#endif
/* USB Configs */
#ifdef CONFIG_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_MASS_STORAGE
#endif
/* Serial Flash */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_LOADADDR 0x12000000
#ifdef CONFIG_NFS_CMD
#define NETWORKBOOT \
"setnetworkboot=" \
"setenv ipaddr 172.16.2.10; setenv serverip 172.16.2.20; " \
"setenv gatewayip 172.16.2.20; setenv nfsserver 172.16.2.20; " \
"setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \
"setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \
"setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \
"setenv bootargs $bootargs cma=128M bootcause=POR ${videoargs} " \
"setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \
"setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \
"networkboot=" \
"run setnetworkboot; " \
"nfs ${loadaddr} /srv/nfs/fitImage; " \
"bootm ${loadaddr}#conf@${confidx}\0" \
#define CONFIG_NETWORKBOOTCOMMAND \
"run networkboot; " \
#else
#define NETWORKBOOT \
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
NETWORKBOOT \
"bootcause=POR\0" \
"image=/boot/fitImage\0" \
"dev=mmc\0" \
"devnum=2\0" \
"rootdev=mmcblk0p\0" \
"quiet=quiet loglevel=0\0" \
"setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
"ro rootwait cma=128M " \
"bootcause=${bootcause} " \
"${quiet} " \
"${videoargs}" "\0" \
"doquiet=" \
"if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
"then setenv quiet; fi\0" \
"hasfirstboot=" \
"test -e ${dev} ${devnum}:${partnum} /boot/bootcause/firstboot\0" \
"swappartitions=" \
"setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
"echo reached failbootcmd; " \
"cls; " \
"setcurs 5 4; " \
"lcdputs \"Monitor failed to start. " \
"Try again, or contact GE Service for support.\"; " \
"bootcount reset; \0" \
"altbootcmd=" \
"run doquiet; " \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run hasfirstboot || setenv partnum 0; " \
"if test ${partnum} != 0; then " \
"setenv bootcause REVERT; " \
"run swappartitions loadimage doboot; " \
"fi; " \
"run failbootcmd\0" \
"loadimage=" \
"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
"doboot=" \
"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
"run setargs; " \
"bootm ${loadaddr}#conf@${confidx}\0" \
"tryboot=" \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run loadimage || run swappartitions && run loadimage || " \
"setenv partnum 0 && echo MISSING IMAGE;" \
"run doboot; " \
"run failbootcmd\0" \
#define CONFIG_MMCBOOTCOMMAND \
"if mmc dev ${devnum}; then " \
"run doquiet; " \
"run tryboot; " \
"fi; " \
#define CONFIG_USBBOOTCOMMAND \
"echo Unsupported; " \
#ifdef CONFIG_NFS_CMD
#define CONFIG_BOOTCOMMAND CONFIG_NETWORKBOOTCOMMAND
#elif CONFIG_CMD_USB
#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND
#else
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* 256M */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* environment organization */
#define CONFIG_SYS_FSL_USDHC_NUM 3
/* Framebuffer */
#define CONFIG_HIDE_LOGO_VERSION
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
#define CONFIG_IMX6_PWM_PER_CLK 66000000
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
#define CONFIG_BCH
#endif /* __GE_BX50V3_CONFIG_H */