u-boot/drivers/pinctrl/pinctrl-stmfx.c
Patrick Delaunay 4c5956086a pinctrl: stmfx: define LOG_CATEGORY
Define LOG_CATEGORY to allow filtering with log command.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-11-30 11:20:34 +01:00

541 lines
13 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
*
* Driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander
* based on Linux driver : pinctrl/pinctrl-stmfx.c
*/
#define LOG_CATEGORY UCLASS_PINCTRL
#include <common.h>
#include <dm.h>
#include <log.h>
#include <i2c.h>
#include <asm/gpio.h>
#include <dm/device.h>
#include <dm/device-internal.h>
#include <dm/device_compat.h>
#include <dm/lists.h>
#include <dm/pinctrl.h>
#include <linux/bitfield.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <power/regulator.h>
/* STMFX pins = GPIO[15:0] + aGPIO[7:0] */
#define STMFX_MAX_GPIO 16
#define STMFX_MAX_AGPIO 8
/* General */
#define STMFX_REG_CHIP_ID 0x00 /* R */
#define STMFX_REG_FW_VERSION_MSB 0x01 /* R */
#define STMFX_REG_FW_VERSION_LSB 0x02 /* R */
#define STMFX_REG_SYS_CTRL 0x40 /* RW */
/* MFX boot time is around 10ms, so after reset, we have to wait this delay */
#define STMFX_BOOT_TIME_MS 10
/* GPIOs expander */
/* GPIO_STATE1 0x10, GPIO_STATE2 0x11, GPIO_STATE3 0x12 */
#define STMFX_REG_GPIO_STATE 0x10 /* R */
/* GPIO_DIR1 0x60, GPIO_DIR2 0x61, GPIO_DIR3 0x63 */
#define STMFX_REG_GPIO_DIR 0x60 /* RW */
/* GPIO_TYPE1 0x64, GPIO_TYPE2 0x65, GPIO_TYPE3 0x66 */
#define STMFX_REG_GPIO_TYPE 0x64 /* RW */
/* GPIO_PUPD1 0x68, GPIO_PUPD2 0x69, GPIO_PUPD3 0x6A */
#define STMFX_REG_GPIO_PUPD 0x68 /* RW */
/* GPO_SET1 0x6C, GPO_SET2 0x6D, GPO_SET3 0x6E */
#define STMFX_REG_GPO_SET 0x6C /* RW */
/* GPO_CLR1 0x70, GPO_CLR2 0x71, GPO_CLR3 0x72 */
#define STMFX_REG_GPO_CLR 0x70 /* RW */
/* STMFX_REG_CHIP_ID bitfields */
#define STMFX_REG_CHIP_ID_MASK GENMASK(7, 0)
/* STMFX_REG_SYS_CTRL bitfields */
#define STMFX_REG_SYS_CTRL_GPIO_EN BIT(0)
#define STMFX_REG_SYS_CTRL_ALTGPIO_EN BIT(3)
#define STMFX_REG_SYS_CTRL_SWRST BIT(7)
#define NR_GPIO_REGS 3
#define NR_GPIOS_PER_REG 8
#define get_reg(offset) ((offset) / NR_GPIOS_PER_REG)
#define get_shift(offset) ((offset) % NR_GPIOS_PER_REG)
#define get_mask(offset) (BIT(get_shift(offset)))
struct stmfx_pinctrl {
struct udevice *gpio;
};
static int stmfx_read(struct udevice *dev, uint offset)
{
return dm_i2c_reg_read(dev_get_parent(dev), offset);
}
static int stmfx_write(struct udevice *dev, uint offset, unsigned int val)
{
return dm_i2c_reg_write(dev_get_parent(dev), offset, val);
}
static int stmfx_read_reg(struct udevice *dev, u8 reg_base, uint offset)
{
u8 reg = reg_base + get_reg(offset);
u32 mask = get_mask(offset);
int ret;
ret = stmfx_read(dev, reg);
if (ret < 0)
return ret;
return ret < 0 ? ret : !!(ret & mask);
}
static int stmfx_write_reg(struct udevice *dev, u8 reg_base, uint offset,
uint val)
{
u8 reg = reg_base + get_reg(offset);
u32 mask = get_mask(offset);
int ret;
ret = stmfx_read(dev, reg);
if (ret < 0)
return ret;
ret = (ret & ~mask) | (val ? mask : 0);
return stmfx_write(dev, reg, ret);
}
static int stmfx_conf_set_pupd(struct udevice *dev, unsigned int offset,
uint pupd)
{
return stmfx_write_reg(dev, STMFX_REG_GPIO_PUPD, offset, pupd);
}
static int stmfx_conf_get_pupd(struct udevice *dev, unsigned int offset)
{
return stmfx_read_reg(dev, STMFX_REG_GPIO_PUPD, offset);
}
static int stmfx_conf_set_type(struct udevice *dev, unsigned int offset,
uint type)
{
return stmfx_write_reg(dev, STMFX_REG_GPIO_TYPE, offset, type);
}
static int stmfx_conf_get_type(struct udevice *dev, unsigned int offset)
{
return stmfx_read_reg(dev, STMFX_REG_GPIO_TYPE, offset);
}
static int stmfx_gpio_get(struct udevice *dev, unsigned int offset)
{
return stmfx_read_reg(dev, STMFX_REG_GPIO_STATE, offset);
}
static int stmfx_gpio_set(struct udevice *dev, unsigned int offset, int value)
{
u32 reg = value ? STMFX_REG_GPO_SET : STMFX_REG_GPO_CLR;
u32 mask = get_mask(offset);
return stmfx_write(dev, reg + get_reg(offset), mask);
}
static int stmfx_gpio_get_function(struct udevice *dev, unsigned int offset)
{
int ret = stmfx_read_reg(dev, STMFX_REG_GPIO_DIR, offset);
if (ret < 0)
return ret;
/* On stmfx, gpio pins direction is (0)input, (1)output. */
return ret ? GPIOF_OUTPUT : GPIOF_INPUT;
}
static int stmfx_gpio_direction_input(struct udevice *dev, unsigned int offset)
{
return stmfx_write_reg(dev, STMFX_REG_GPIO_DIR, offset, 0);
}
static int stmfx_gpio_direction_output(struct udevice *dev,
unsigned int offset, int value)
{
int ret = stmfx_gpio_set(dev, offset, value);
if (ret < 0)
return ret;
return stmfx_write_reg(dev, STMFX_REG_GPIO_DIR, offset, 1);
}
static int stmfx_gpio_set_flags(struct udevice *dev, unsigned int offset,
ulong flags)
{
int ret = -ENOTSUPP;
if (flags & GPIOD_IS_OUT) {
bool value = flags & GPIOD_IS_OUT_ACTIVE;
if (flags & GPIOD_OPEN_SOURCE)
return -ENOTSUPP;
if (flags & GPIOD_OPEN_DRAIN)
ret = stmfx_conf_set_type(dev, offset, 0);
else /* PUSH-PULL */
ret = stmfx_conf_set_type(dev, offset, 1);
if (ret)
return ret;
ret = stmfx_gpio_direction_output(dev, offset, value);
} else if (flags & GPIOD_IS_IN) {
ret = stmfx_gpio_direction_input(dev, offset);
if (ret)
return ret;
if (flags & GPIOD_PULL_UP) {
ret = stmfx_conf_set_type(dev, offset, 1);
if (ret)
return ret;
ret = stmfx_conf_set_pupd(dev, offset, 1);
} else if (flags & GPIOD_PULL_DOWN) {
ret = stmfx_conf_set_type(dev, offset, 1);
if (ret)
return ret;
ret = stmfx_conf_set_pupd(dev, offset, 0);
}
}
return ret;
}
static int stmfx_gpio_get_flags(struct udevice *dev, unsigned int offset,
ulong *flagsp)
{
ulong dir_flags = 0;
int ret;
if (stmfx_gpio_get_function(dev, offset) == GPIOF_OUTPUT) {
dir_flags |= GPIOD_IS_OUT;
ret = stmfx_conf_get_type(dev, offset);
if (ret < 0)
return ret;
if (ret == 0)
dir_flags |= GPIOD_OPEN_DRAIN;
/* 1 = push-pull (default), open source not supported */
ret = stmfx_gpio_get(dev, offset);
if (ret < 0)
return ret;
if (ret)
dir_flags |= GPIOD_IS_OUT_ACTIVE;
} else {
dir_flags |= GPIOD_IS_IN;
ret = stmfx_conf_get_type(dev, offset);
if (ret < 0)
return ret;
if (ret == 1) {
ret = stmfx_conf_get_pupd(dev, offset);
if (ret < 0)
return ret;
if (ret == 1)
dir_flags |= GPIOD_PULL_UP;
else
dir_flags |= GPIOD_PULL_DOWN;
}
}
*flagsp = dir_flags;
return 0;
}
static int stmfx_gpio_probe(struct udevice *dev)
{
struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
struct ofnode_phandle_args args;
u8 sys_ctrl;
uc_priv->bank_name = "stmfx";
uc_priv->gpio_count = STMFX_MAX_GPIO + STMFX_MAX_AGPIO;
if (!dev_read_phandle_with_args(dev, "gpio-ranges",
NULL, 3, 0, &args)) {
uc_priv->gpio_count = args.args[2];
}
/* enable GPIO function */
sys_ctrl = STMFX_REG_SYS_CTRL_GPIO_EN;
if (uc_priv->gpio_count > STMFX_MAX_GPIO)
sys_ctrl |= STMFX_REG_SYS_CTRL_ALTGPIO_EN;
stmfx_write(dev, STMFX_REG_SYS_CTRL, sys_ctrl);
return 0;
}
static const struct dm_gpio_ops stmfx_gpio_ops = {
.set_value = stmfx_gpio_set,
.get_value = stmfx_gpio_get,
.get_function = stmfx_gpio_get_function,
.direction_input = stmfx_gpio_direction_input,
.direction_output = stmfx_gpio_direction_output,
.set_flags = stmfx_gpio_set_flags,
.get_flags = stmfx_gpio_get_flags,
};
U_BOOT_DRIVER(stmfx_gpio) = {
.name = "stmfx-gpio",
.id = UCLASS_GPIO,
.probe = stmfx_gpio_probe,
.ops = &stmfx_gpio_ops,
};
#if CONFIG_IS_ENABLED(PINCONF)
static const struct pinconf_param stmfx_pinctrl_conf_params[] = {
{ "bias-disable", PIN_CONFIG_BIAS_DISABLE, 0 },
{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 0 },
{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 0 },
{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 0 },
{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
{ "output-high", PIN_CONFIG_OUTPUT, 1 },
{ "output-low", PIN_CONFIG_OUTPUT, 0 },
};
static int stmfx_pinctrl_conf_set(struct udevice *dev, unsigned int pin,
unsigned int param, unsigned int arg)
{
int ret, dir;
struct stmfx_pinctrl *plat = dev_get_plat(dev);
dir = stmfx_gpio_get_function(plat->gpio, pin);
if (dir < 0)
return dir;
switch (param) {
case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
case PIN_CONFIG_BIAS_DISABLE:
case PIN_CONFIG_DRIVE_PUSH_PULL:
ret = stmfx_conf_set_type(dev, pin, 0);
break;
case PIN_CONFIG_BIAS_PULL_DOWN:
ret = stmfx_conf_set_type(dev, pin, 1);
if (ret)
return ret;
ret = stmfx_conf_set_pupd(dev, pin, 0);
break;
case PIN_CONFIG_BIAS_PULL_UP:
ret = stmfx_conf_set_type(dev, pin, 1);
if (ret)
return ret;
ret = stmfx_conf_set_pupd(dev, pin, 1);
break;
case PIN_CONFIG_DRIVE_OPEN_DRAIN:
ret = stmfx_conf_set_type(dev, pin, 1);
break;
case PIN_CONFIG_OUTPUT:
ret = stmfx_gpio_direction_output(plat->gpio, pin, arg);
break;
default:
return -ENOTSUPP;
}
return ret;
}
#endif
static int stmfx_pinctrl_get_pins_count(struct udevice *dev)
{
struct stmfx_pinctrl *plat = dev_get_plat(dev);
struct gpio_dev_priv *uc_priv;
uc_priv = dev_get_uclass_priv(plat->gpio);
return uc_priv->gpio_count;
}
/*
* STMFX pins[15:0] are called "gpio[15:0]"
* and STMFX pins[23:16] are called "agpio[7:0]"
*/
static char pin_name[PINNAME_SIZE];
static const char *stmfx_pinctrl_get_pin_name(struct udevice *dev,
unsigned int selector)
{
if (selector < STMFX_MAX_GPIO)
snprintf(pin_name, PINNAME_SIZE, "gpio%u", selector);
else
snprintf(pin_name, PINNAME_SIZE, "agpio%u", selector - 16);
return pin_name;
}
static const char *stmfx_pinctrl_get_pin_conf(struct udevice *dev,
unsigned int pin, int func)
{
int pupd, type;
type = stmfx_conf_get_type(dev, pin);
if (type < 0)
return "";
if (func == GPIOF_OUTPUT) {
if (type)
return "drive-open-drain";
else
return ""; /* default: push-pull*/
}
if (!type)
return ""; /* default: bias-disable*/
pupd = stmfx_conf_get_pupd(dev, pin);
if (pupd < 0)
return "";
if (pupd)
return "bias-pull-up";
else
return "bias-pull-down";
}
static int stmfx_pinctrl_get_pin_muxing(struct udevice *dev,
unsigned int selector,
char *buf, int size)
{
struct stmfx_pinctrl *plat = dev_get_plat(dev);
int func;
func = stmfx_gpio_get_function(plat->gpio, selector);
if (func < 0)
return func;
snprintf(buf, size, "%s ", func == GPIOF_INPUT ? "input" : "output");
strncat(buf, stmfx_pinctrl_get_pin_conf(dev, selector, func), size);
return 0;
}
static int stmfx_pinctrl_bind(struct udevice *dev)
{
struct stmfx_pinctrl *plat = dev_get_plat(dev);
/* subnode name is not explicit: use father name */
device_set_name(dev, dev->parent->name);
return device_bind_driver_to_node(dev->parent,
"stmfx-gpio", dev->parent->name,
dev_ofnode(dev), &plat->gpio);
};
static int stmfx_pinctrl_probe(struct udevice *dev)
{
struct stmfx_pinctrl *plat = dev_get_plat(dev);
return device_probe(plat->gpio);
};
const struct pinctrl_ops stmfx_pinctrl_ops = {
.get_pins_count = stmfx_pinctrl_get_pins_count,
.get_pin_name = stmfx_pinctrl_get_pin_name,
.set_state = pinctrl_generic_set_state,
.get_pin_muxing = stmfx_pinctrl_get_pin_muxing,
#if CONFIG_IS_ENABLED(PINCONF)
.pinconf_set = stmfx_pinctrl_conf_set,
.pinconf_num_params = ARRAY_SIZE(stmfx_pinctrl_conf_params),
.pinconf_params = stmfx_pinctrl_conf_params,
#endif
};
static const struct udevice_id stmfx_pinctrl_match[] = {
{ .compatible = "st,stmfx-0300-pinctrl", },
};
U_BOOT_DRIVER(stmfx_pinctrl) = {
.name = "stmfx-pinctrl",
.id = UCLASS_PINCTRL,
.of_match = of_match_ptr(stmfx_pinctrl_match),
.bind = stmfx_pinctrl_bind,
.probe = stmfx_pinctrl_probe,
.ops = &stmfx_pinctrl_ops,
.plat_auto = sizeof(struct stmfx_pinctrl),
};
static int stmfx_chip_init(struct udevice *dev)
{
u8 id;
u8 version[2];
int ret;
struct dm_i2c_chip *chip = dev_get_parent_plat(dev);
ret = dm_i2c_reg_read(dev, STMFX_REG_CHIP_ID);
if (ret < 0) {
dev_err(dev, "error reading chip id: %d\n", ret);
return ret;
}
id = (u8)ret;
/*
* Check that ID is the complement of the I2C address:
* STMFX I2C address follows the 7-bit format (MSB), that's why
* client->addr is shifted.
*
* STMFX_I2C_ADDR| STMFX | Linux
* input pin | I2C device address | I2C device address
*---------------------------------------------------------
* 0 | b: 1000 010x h:0x84 | 0x42
* 1 | b: 1000 011x h:0x86 | 0x43
*/
if (FIELD_GET(STMFX_REG_CHIP_ID_MASK, ~id) != (chip->chip_addr << 1)) {
dev_err(dev, "unknown chip id: %#x\n", id);
return -EINVAL;
}
ret = dm_i2c_read(dev, STMFX_REG_FW_VERSION_MSB,
version, sizeof(version));
if (ret) {
dev_err(dev, "error reading fw version: %d\n", ret);
return ret;
}
dev_info(dev, "STMFX id: %#x, fw version: %x.%02x\n",
id, version[0], version[1]);
ret = dm_i2c_reg_read(dev, STMFX_REG_SYS_CTRL);
if (ret < 0)
return ret;
ret = dm_i2c_reg_write(dev, STMFX_REG_SYS_CTRL,
ret | STMFX_REG_SYS_CTRL_SWRST);
if (ret)
return ret;
mdelay(STMFX_BOOT_TIME_MS);
return ret;
}
static int stmfx_probe(struct udevice *dev)
{
struct udevice *vdd;
int ret;
ret = device_get_supply_regulator(dev, "vdd-supply", &vdd);
if (ret && ret != -ENOENT) {
dev_err(dev, "vdd regulator error:%d\n", ret);
return ret;
}
if (!ret) {
ret = regulator_set_enable(vdd, true);
if (ret) {
dev_err(dev, "vdd enable failed: %d\n", ret);
return ret;
}
}
return stmfx_chip_init(dev);
}
static const struct udevice_id stmfx_match[] = {
{ .compatible = "st,stmfx-0300", },
};
U_BOOT_DRIVER(stmfx) = {
.name = "stmfx",
.id = UCLASS_I2C_GENERIC,
.of_match = of_match_ptr(stmfx_match),
.probe = stmfx_probe,
.bind = dm_scan_fdt_dev,
};