mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-25 14:10:43 +00:00
45964cbf3c
Migrate DH DRC02 device trees from Linux commit 42226c989789 (tag v5.18-rc7). No changes have been made, the DTs are exact copies. Furthermore add the DTB to dh_imx6_defconfig. Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Philip Oberfichtner <pro@denx.de>
143 lines
3.6 KiB
Text
143 lines
3.6 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2021 DH electronics GmbH
|
|
*/
|
|
|
|
/ {
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
};
|
|
|
|
/*
|
|
* Special SoM hardware required which uses the pins from micro SD card. The
|
|
* pins SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2
|
|
* Tx and Rx are routed to the DHCOM UART1 rts/cts pins. Therefore the micro SD
|
|
* card must be disabled and the uart1 rts/cts must be output on other DHCOM
|
|
* pins, see uart1 and usdhc3 node below.
|
|
*/
|
|
&can2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
/*
|
|
* NOTE: On DRC02, the RS485_RX_En is controlled by a separate
|
|
* GPIO line, however the i.MX6 UART driver assumes RX happens
|
|
* during TX anyway and that it only controls drive enable DE
|
|
* line. Hence, the RX is always enabled here.
|
|
*/
|
|
rs485-rx-en-hog {
|
|
gpio-hog;
|
|
gpios = <18 0>; /* GPIO Q */
|
|
line-name = "rs485-rx-en";
|
|
output-low;
|
|
};
|
|
};
|
|
|
|
&gpio3 {
|
|
gpio-line-names =
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "DRC02-In1", "", "", "", "";
|
|
};
|
|
|
|
&gpio4 {
|
|
gpio-line-names =
|
|
"", "", "", "", "", "DHCOM-E", "DRC02-In2", "DHCOM-H",
|
|
"DHCOM-I", "DRC02-HW0", "", "", "", "", "", "",
|
|
"", "", "", "", "DRC02-Out1", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&gpio6 {
|
|
gpio-line-names =
|
|
"", "", "", "DRC02-Out2", "", "", "SOM-HW1", "",
|
|
"", "", "", "", "", "", "DRC02-HW2", "DRC02-HW1",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&i2c1 {
|
|
eeprom@50 {
|
|
compatible = "atmel,24c04";
|
|
reg = <0x50>;
|
|
pagesize = <16>;
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
/*
|
|
* Due to the use of can2 the signals for can2 Tx and Rx are routed to
|
|
* DHCOM UART1 rts/cts pins. Therefore this UART have to use DHCOM GPIOs
|
|
* for rts/cts. So configure DHCOM GPIO I as rts and GPIO M as cts.
|
|
*/
|
|
/delete-property/ uart-has-rtscts;
|
|
cts-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; /* GPIO M */
|
|
pinctrl-0 = <&pinctrl_uart1 &pinctrl_dhcom_i &pinctrl_dhcom_m>;
|
|
pinctrl-names = "default";
|
|
rts-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
|
|
};
|
|
|
|
&uart5 {
|
|
/*
|
|
* On DRC02 this UART is used as RS485 interface and RS485_TX_En is
|
|
* controlled by DHCOM GPIO P. So remove rts/cts pins and the property
|
|
* uart-has-rtscts from this UART and add the DHCOM GPIO P pin via
|
|
* rts-gpios. The RS485_RX_En is controlled by DHCOM GPIO Q, see gpio1
|
|
* node above.
|
|
*/
|
|
/delete-property/ uart-has-rtscts;
|
|
linux,rs485-enabled-at-boot-time;
|
|
pinctrl-0 = <&pinctrl_uart5_core &pinctrl_dhcom_p &pinctrl_dhcom_q>;
|
|
pinctrl-names = "default";
|
|
rts-gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>; /* GPIO P */
|
|
};
|
|
|
|
&usbh1 {
|
|
disable-over-current;
|
|
};
|
|
|
|
&usdhc2 { /* SD card */
|
|
status = "okay";
|
|
};
|
|
|
|
&usdhc3 {
|
|
/*
|
|
* Due to the use of can2 the micro SD card on module have to be
|
|
* disabled, because the pins SD3_DAT0 and SD3_DAT1 are muxed as
|
|
* can2 Tx and Rx.
|
|
*/
|
|
status = "disabled";
|
|
};
|
|
|
|
&iomuxc {
|
|
pinctrl-0 = <
|
|
/*
|
|
* The following DHCOM GPIOs are used on this board.
|
|
* Therefore, they have been removed from the list below.
|
|
* I: uart1 rts
|
|
* M: uart1 cts
|
|
* P: uart5 rs485-tx-en
|
|
* Q: uart5 rs485-rx-en
|
|
*/
|
|
&pinctrl_hog_base
|
|
&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
|
|
&pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
|
|
&pinctrl_dhcom_g &pinctrl_dhcom_h
|
|
&pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
|
|
&pinctrl_dhcom_n &pinctrl_dhcom_o
|
|
&pinctrl_dhcom_r
|
|
&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
|
|
&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
|
|
>;
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl_uart5_core: uart5-core-grp {
|
|
fsl,pins = <
|
|
MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
|
|
MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
|
|
>;
|
|
};
|
|
};
|