u-boot/include/configs/omap3_beagle.h
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

239 lines
7.4 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2006-2008
* Texas Instruments.
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <x0khasim@ti.com>
*
* Configuration settings for the TI OMAP3530 Beagle board.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#include <configs/ti_omap3_common.h>
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
*/
#undef CONFIG_SPL_TEXT_BASE
#define CONFIG_SPL_TEXT_BASE 0x40200000
#define CONFIG_MISC_INIT_R
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
/* NAND */
#if defined(CONFIG_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_SYS_ENV_SECT_SIZE SZ_128K
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
#define CONFIG_ENV_OVERWRITE
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
/* NAND: SPL falcon mode configs */
#if defined(CONFIG_SPL_OS_BOOT)
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x2a0000
#endif /* CONFIG_SPL_OS_BOOT */
#endif /* CONFIG_NAND */
/* USB EHCI */
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
/* Enable Multi Bus support for I2C */
#define CONFIG_I2C_MULTI_BUS
/* DSS Support */
#define CONFIG_VIDEO_OMAP3
/* TWL4030 LED Support */
#define CONFIG_TWL4030_LED
/* Environment */
#define CONFIG_ENV_SIZE SZ_128K
#define CONFIG_PREBOOT "usb start"
#define MEM_LAYOUT_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV
#define BOOTENV_DEV_LEGACY_MMC(devtypeu, devtypel, instance) \
"bootcmd_" #devtypel #instance "=" \
"setenv mmcdev " #instance "; " \
"run mmcboot\0"
#define BOOTENV_DEV_NAME_LEGACY_MMC(devtypeu, devtypel, instance) \
#devtypel #instance " "
#if defined(CONFIG_NAND)
#define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
"bootcmd_" #devtypel #instance "=" \
"if test ${mtdids} = '' || test ${mtdparts} = '' ; then " \
"echo NAND boot disabled: No mtdids and/or mtdparts; " \
"else " \
"run nandboot; " \
"fi\0"
#define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
#devtypel #instance " "
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(LEGACY_MMC, legacy_mmc, 0) \
func(UBIFS, ubifs, 0) \
func(NAND, nand, 0)
#else /* !CONFIG_NAND */
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(LEGACY_MMC, legacy_mmc, 0)
#endif /* CONFIG_NAND */
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
MEM_LAYOUT_ENV_SETTINGS \
"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_high=0xffffffff\0" \
"console=ttyO2,115200n8\0" \
"bootdir=/boot\0" \
"bootenv=uEnv.txt\0" \
"bootfile=zImage\0" \
"bootpart=0:2\0" \
"bootubivol=rootfs\0" \
"bootubipart=rootfs\0" \
"usbtty=cdc_acm\0" \
"mpurate=auto\0" \
"buddy=none\0" \
"camera=none\0" \
"vram=12M\0" \
"dvimode=640x480MR-16@60\0" \
"defaultdisplay=dvi\0" \
"defaultargs=setenv defargs " \
"mpurate=${mpurate} " \
"buddy=${buddy} "\
"camera=${camera} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay}\0" \
"optargs=\0" \
"findfdt=" \
"if test $beaglerev = AxBx; then " \
"setenv fdtfile omap3-beagle.dtb; fi; " \
"if test $beaglerev = Cx; then " \
"setenv fdtfile omap3-beagle.dtb; fi; " \
"if test $beaglerev = C4; then " \
"setenv fdtfile omap3-beagle.dtb; fi; " \
"if test $beaglerev = xMAB; then " \
"setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
"if test $beaglerev = xMC; then " \
"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
"if test $fdtfile = undefined; then " \
"echo WARNING: Could not determine device tree to use; fi\0" \
"mmcdev=0\0" \
"mmcpart=2\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext4 rootwait\0" \
"mmcargs=run defaultargs; setenv bootargs console=${console} " \
"${mtdparts} " \
"${defargs} " \
"${optargs} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"userbutton_xm=gpio input 4;\0" \
"userbutton_nonxm=gpio input 7;\0" \
"userbutton=if gpio input 173; then " \
"run userbutton_xm; " \
"else " \
"run userbutton_nonxm; " \
"fi;\0" \
"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
"ext4bootenv=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootenv}\0" \
"importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
"env import -t ${loadaddr} ${filesize}\0" \
"mmcbootenv=setenv bootpart ${mmcdev}:${mmcpart}; " \
"mmc dev ${mmcdev}; " \
"if mmc rescan; then " \
"if run userbutton; then " \
"setenv bootenv uEnv.txt;" \
"else " \
"setenv bootenv user.txt;" \
"fi;" \
"run loadbootenv && run importbootenv; " \
"run ext4bootenv && run importbootenv; " \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...; " \
"run uenvcmd; " \
"fi; " \
"fi\0" \
"validatefdt=" \
"if test $beaglerev = xMAB; then " \
"if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
"setenv fdtfile omap3-beagle-xm.dtb; " \
"fi; " \
"fi; \0" \
"loadimage=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
"loaddtb=run validatefdt; ext4load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
"mmcboot=run mmcbootenv; " \
"if run loadimage && run loaddtb; then " \
"echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} ...; " \
"run mmcargs; " \
"if test ${bootfile} = uImage; then " \
"bootm ${loadaddr} - ${fdtaddr}; " \
"fi; " \
"if test ${bootfile} = zImage; then " \
"bootz ${loadaddr} - ${fdtaddr}; " \
"fi; " \
"fi\0" \
"nandroot=ubi0:rootfs ubi.mtd=rootfs rw\0" \
"nandrootfstype=ubifs rootwait\0" \
"nandargs=run defaultargs; setenv bootargs console=${console} " \
"${mtdparts} " \
"${defargs} " \
"${optargs} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"nandboot=if nand read ${loadaddr} kernel && nand read ${fdtaddr} dtb; then " \
"echo Booting uImage from NAND MTD 'kernel' partition ...; " \
"run nandargs; " \
"bootm ${loadaddr} - ${fdtaddr}; " \
"fi\0" \
"loadramdisk=ext4load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
"ramdisk=rootfs.ext2.gz.uboot\0" \
"ramdisk_size=16384\0" \
"ramroot=/dev/ram rw\0" \
"ramrootfstype=ext2\0" \
"ramargs=run defaultargs; setenv bootargs console=${console} " \
"${mtdparts} " \
"${defargs} " \
"${optargs} " \
"root=${ramroot} ramdisk_size=${ramdisk_size} " \
"rootfstype=${ramrootfstype}\0" \
"ramboot=run mmcbootenv; " \
"if run loadimage && run loaddtb && run loadramdisk; then " \
"echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} w/ramdisk ...; " \
"run ramargs; " \
"bootz ${loadaddr} ${rdaddr} ${fdtaddr}; " \
"fi\0" \
BOOTENV
#endif /* __CONFIG_H */