mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 18:28:55 +00:00
2fe88d4522
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
580 lines
17 KiB
C
580 lines
17 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
|
|
*
|
|
* Dave Liu <daveliu@freescale.com>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
|
|
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
|
|
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
|
|
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
|
|
|
|
#ifndef CONFIG_SYS_MONITOR_BASE
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#endif
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1 /* E300 family */
|
|
#define CONFIG_MPC831x 1 /* MPC831x CPU family */
|
|
#define CONFIG_MPC8315 1 /* MPC8315 CPU specific */
|
|
#define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */
|
|
|
|
/*
|
|
* System Clock Setup
|
|
*/
|
|
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
|
|
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
|
|
|
|
/*
|
|
* Hardware Reset Configuration Word
|
|
* if CLKIN is 66.66MHz, then
|
|
* CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
|
|
*/
|
|
#define CONFIG_SYS_HRCW_LOW (\
|
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
|
HRCWL_DDR_TO_SCB_CLK_2X1 |\
|
|
HRCWL_SVCOD_DIV_2 |\
|
|
HRCWL_CSB_TO_CLKIN_2X1 |\
|
|
HRCWL_CORE_TO_CSB_3X1)
|
|
#define CONFIG_SYS_HRCW_HIGH_BASE (\
|
|
HRCWH_PCI_HOST |\
|
|
HRCWH_PCI1_ARBITER_ENABLE |\
|
|
HRCWH_CORE_ENABLE |\
|
|
HRCWH_BOOTSEQ_DISABLE |\
|
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
|
HRCWH_TSEC1M_IN_RGMII |\
|
|
HRCWH_TSEC2M_IN_RGMII |\
|
|
HRCWH_BIG_ENDIAN |\
|
|
HRCWH_LALE_NORMAL)
|
|
|
|
#ifdef CONFIG_NAND_SPL
|
|
#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
|
|
HRCWH_FROM_0XFFF00100 |\
|
|
HRCWH_ROM_LOC_NAND_SP_8BIT |\
|
|
HRCWH_RL_EXT_NAND)
|
|
#else
|
|
#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
|
|
HRCWH_FROM_0X00000100 |\
|
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
|
HRCWH_RL_EXT_LEGACY)
|
|
#endif
|
|
|
|
/*
|
|
* System IO Config
|
|
*/
|
|
#define CONFIG_SYS_SICRH 0x00000000
|
|
#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */
|
|
|
|
#define CONFIG_HWCONFIG
|
|
|
|
/*
|
|
* IMMR new address
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xE0000000
|
|
|
|
/*
|
|
* Arbiter Setup
|
|
*/
|
|
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
|
|
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
|
|
#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
|
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
|
|
| DDRCDR_PZ_LOZ \
|
|
| DDRCDR_NZ_LOZ \
|
|
| DDRCDR_ODT \
|
|
| DDRCDR_Q_DRN)
|
|
/* 0x7b880001 */
|
|
/*
|
|
* Manually set up DDR parameters
|
|
* consist of two chips HY5PS12621BFP-C4 from HYNIX
|
|
*/
|
|
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
|
|
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
|
|
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
|
|
| CSCONFIG_ODT_RD_NEVER \
|
|
| CSCONFIG_ODT_WR_ONLY_CURRENT \
|
|
| CSCONFIG_ROW_BIT_13 \
|
|
| CSCONFIG_COL_BIT_10)
|
|
/* 0x80010102 */
|
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
|
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
|
|
| (0 << TIMING_CFG0_WRT_SHIFT) \
|
|
| (0 << TIMING_CFG0_RRT_SHIFT) \
|
|
| (0 << TIMING_CFG0_WWT_SHIFT) \
|
|
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
|
|
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
|
|
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
|
|
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
|
|
/* 0x00220802 */
|
|
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
|
|
| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
|
|
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
|
|
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
|
|
| (6 << TIMING_CFG1_REFREC_SHIFT) \
|
|
| (2 << TIMING_CFG1_WRREC_SHIFT) \
|
|
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
|
|
| (2 << TIMING_CFG1_WRTORD_SHIFT))
|
|
/* 0x27256222 */
|
|
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
|
|
| (4 << TIMING_CFG2_CPO_SHIFT) \
|
|
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
|
|
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
|
|
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
|
|
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
|
|
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
|
|
/* 0x121048c5 */
|
|
#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
|
|
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
|
|
/* 0x03600100 */
|
|
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
|
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
|
| SDRAM_CFG_DBW_32)
|
|
/* 0x43080000 */
|
|
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
|
|
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
|
|
| (0x0232 << SDRAM_MODE_SD_SHIFT))
|
|
/* ODT 150ohm CL=3, AL=1 on SDRAM */
|
|
#define CONFIG_SYS_DDR_MODE2 0x00000000
|
|
|
|
/*
|
|
* Memory test
|
|
*/
|
|
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
|
|
#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00140000
|
|
|
|
/*
|
|
* The reserved memory
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Initial RAM Base Address Setup
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
|
|
/*
|
|
* Local Bus Configuration & Clock Setup
|
|
*/
|
|
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
|
|
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
|
|
#define CONFIG_SYS_LBC_LBCR 0x00040000
|
|
#define CONFIG_FSL_ELBC 1
|
|
|
|
/*
|
|
* FLASH on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
|
|
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
|
|
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
|
|
|
|
/* Window base at flash base */
|
|
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
|
|
|
|
#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \
|
|
| BR_PS_16 /* 16 bit port */ \
|
|
| BR_MS_GPCM /* MSEL = GPCM */ \
|
|
| BR_V) /* valid */
|
|
#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
|
|
| OR_UPM_XAM \
|
|
| OR_GPCM_CSNT \
|
|
| OR_GPCM_ACS_DIV2 \
|
|
| OR_GPCM_XACS \
|
|
| OR_GPCM_SCY_15 \
|
|
| OR_GPCM_TRLX_SET \
|
|
| OR_GPCM_EHTR_SET \
|
|
| OR_GPCM_EAD)
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
/* 127 64KB sectors and 8 8KB top sectors per device */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 135
|
|
|
|
#undef CONFIG_SYS_FLASH_CHECKSUM
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
/*
|
|
* NAND Flash on the Local Bus
|
|
*/
|
|
|
|
#ifdef CONFIG_NAND_SPL
|
|
#define CONFIG_SYS_NAND_BASE 0xFFF00000
|
|
#else
|
|
#define CONFIG_SYS_NAND_BASE 0xE0600000
|
|
#endif
|
|
|
|
#define CONFIG_MTD_PARTITION
|
|
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_NAND_FSL_ELBC 1
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
|
|
#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
|
|
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
|
|
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
|
|
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
|
|
|
|
#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
|
|
| BR_DECC_CHK_GEN /* Use HW ECC */ \
|
|
| BR_PS_8 /* 8 bit port */ \
|
|
| BR_MS_FCM /* MSEL = FCM */ \
|
|
| BR_V) /* valid */
|
|
#define CONFIG_SYS_NAND_OR_PRELIM \
|
|
(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
|
|
| OR_FCM_CSCT \
|
|
| OR_FCM_CST \
|
|
| OR_FCM_CHT \
|
|
| OR_FCM_SCY_1 \
|
|
| OR_FCM_TRLX \
|
|
| OR_FCM_EHTR)
|
|
/* 0xFFFF8396 */
|
|
|
|
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
|
|
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
|
|
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
|
|
|
|
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
|
|
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
|
|
|
|
#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
|
|
#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
|
|
|
|
#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
|
|
!defined(CONFIG_NAND_SPL)
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#else
|
|
#undef CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_FSL
|
|
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
|
|
|
|
/*
|
|
* Board info - revision and where boot from
|
|
*/
|
|
#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
|
|
|
|
/*
|
|
* Config on-board RTC
|
|
*/
|
|
#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
|
|
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
|
|
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
|
|
#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
|
|
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
|
|
#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
|
|
#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
|
|
|
|
#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
|
|
#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
|
|
|
|
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
|
|
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
|
|
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
|
|
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
|
|
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
|
|
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
|
|
|
|
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
|
|
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
|
|
#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
|
|
#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
|
|
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
|
|
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
|
|
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE
|
|
#define CONFIG_PCIE
|
|
|
|
#define CONFIG_EEPRO100
|
|
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
|
|
|
#define CONFIG_HAS_FSL_DR_USB
|
|
#define CONFIG_SYS_SCCR_USBDRCM 3
|
|
|
|
#define CONFIG_USB_EHCI_FSL
|
|
#define CONFIG_USB_PHY_TYPE "utmi"
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
|
|
/*
|
|
* TSEC
|
|
*/
|
|
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
|
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
|
|
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
|
|
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
|
|
|
|
/*
|
|
* TSEC ethernet configuration
|
|
*/
|
|
#define CONFIG_TSEC1 1
|
|
#define CONFIG_TSEC1_NAME "eTSEC0"
|
|
#define CONFIG_TSEC2 1
|
|
#define CONFIG_TSEC2_NAME "eTSEC1"
|
|
#define TSEC1_PHY_ADDR 0
|
|
#define TSEC2_PHY_ADDR 1
|
|
#define TSEC1_PHYIDX 0
|
|
#define TSEC2_PHYIDX 0
|
|
#define TSEC1_FLAGS TSEC_GIGABIT
|
|
#define TSEC2_FLAGS TSEC_GIGABIT
|
|
|
|
/* Options are: eTSEC[0-1] */
|
|
#define CONFIG_ETHPRIME "eTSEC1"
|
|
|
|
/*
|
|
* SATA
|
|
*/
|
|
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
|
#define CONFIG_SATA1
|
|
#define CONFIG_SYS_SATA1_OFFSET 0x18000
|
|
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
|
|
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
|
#define CONFIG_SATA2
|
|
#define CONFIG_SYS_SATA2_OFFSET 0x19000
|
|
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
|
|
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
|
|
|
#ifdef CONFIG_FSL_SATA
|
|
#define CONFIG_LBA48
|
|
#endif
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#if !defined(CONFIG_SYS_RAMBOOT)
|
|
#define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#else
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 256 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
|
|
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
|
|
|
/*
|
|
* Core HID Setup
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT 0x000000000
|
|
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
|
|
HID0_ENABLE_INSTRUCTION_CACHE | \
|
|
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
|
|
#define CONFIG_SYS_HID2 HID2_HBE
|
|
|
|
/*
|
|
* MMU Setup
|
|
*/
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
/* DDR: cache cacheable */
|
|
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
|
|
| BATL_PP_RW \
|
|
| BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
|
|
| BATU_BL_128M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
|
|
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
|
|
|
|
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
|
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
|
|
| BATL_PP_RW \
|
|
| BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
|
|
| BATU_BL_8M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
|
|
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
|
|
|
|
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
|
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \
|
|
| BATL_PP_RW \
|
|
| BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \
|
|
| BATU_BL_32M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \
|
|
| BATL_PP_RW \
|
|
| BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
|
|
|
|
/* Stack in dcache: cacheable, no memory coherence */
|
|
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
|
|
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \
|
|
| BATU_BL_128K \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
|
|
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
|
|
|
|
/* PCI MEM space: cacheable */
|
|
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS \
|
|
| BATL_PP_RW \
|
|
| BATL_MEMCOHERENCE)
|
|
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS \
|
|
| BATU_BL_256M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
|
|
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
|
|
|
|
/* PCI MMIO space: cache-inhibit and guarded */
|
|
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS \
|
|
| BATL_PP_RW \
|
|
| BATL_CACHEINHIBIT \
|
|
| BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS \
|
|
| BATU_BL_256M \
|
|
| BATU_VS \
|
|
| BATU_VP)
|
|
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
|
|
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
|
|
|
|
#define CONFIG_SYS_IBAT6L 0
|
|
#define CONFIG_SYS_IBAT6U 0
|
|
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
|
|
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
|
|
|
|
#define CONFIG_SYS_IBAT7L 0
|
|
#define CONFIG_SYS_IBAT7U 0
|
|
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
|
|
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#if defined(CONFIG_TSEC_ENET)
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_HAS_ETH1
|
|
#endif
|
|
|
|
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"consoledev=ttyS0\0" \
|
|
"ramdiskaddr=1000000\0" \
|
|
"ramdiskfile=ramfs.83xx\0" \
|
|
"fdtaddr=780000\0" \
|
|
"fdtfile=mpc8315erdb.dtb\0" \
|
|
"usb_phy_type=utmi\0" \
|
|
""
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
|
|
"$netdev:off " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
|
|
|
|
#endif /* __CONFIG_H */
|