u-boot/include/configs/ls1028a_common.h
Tom Rini 7cfbba36e9 Convert CONFIG_SYS_MALLOC_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31 17:47:49 -04:00

111 lines
2.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2019-2021 NXP
*/
#ifndef __L1028A_COMMON_H
#define __L1028A_COMMON_H
#define CONFIG_REMAKE_ELF
#define CONFIG_MP
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 1
/*
* SMP Definitinos
*/
#define CPU_RELEASE_ADDR secondary_boot_addr
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* GPIO */
#ifdef CONFIG_DM_GPIO
#ifndef CONFIG_MPC8XXX_GPIO
#define CONFIG_MPC8XXX_GPIO
#endif
#endif
/* I2C */
/* Serial Port */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* Miscellaneous configurable options */
/* Physical Memory Map */
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(MMC, mmc, 1) \
func(USB, usb, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#undef CONFIG_BOOTCOMMAND
#define XSPI_NOR_BOOTCOMMAND \
"run xspi_hdploadcmd; run distro_bootcmd; run xspi_bootcmd; " \
"env exists secureboot && esbc_halt;;"
#define SD_BOOTCOMMAND \
"run sd_hdploadcmd; run distro_bootcmd;run sd_bootcmd; " \
"env exists secureboot && esbc_halt;"
#define SD2_BOOTCOMMAND \
"run emmc_hdploadcmd; run distro_bootcmd;run emmc_bootcmd; " \
"env exists secureboot && esbc_halt;"
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#define OCRAM_NONSECURE_SIZE 0x00010000
#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
#define I2C_MUX_CH_DEFAULT 0x8
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
/* DisplayPort */
#define DP_PWD_EN_DEFAULT_MASK 0x8
#ifdef CONFIG_NXP_ESBC
#include <asm/fsl_secure_boot.h>
#endif
/* Ethernet */
/* smallest ENETC BD ring has 8 entries */
#define CONFIG_SYS_RX_ETH_BUFFER 8
#endif /* __L1028A_COMMON_H */