mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 10:18:38 +00:00
877bfe37dc
This patch introduces the support for Keymile's kmp204x reference design. This design is based on Freescale's P2040/P2041 SoC. The peripherals used by this design are: - DDR3 RAM with SPD support - SPI NOR Flash as boot medium - NAND Flash - 2 PCIe busses (hosts 1 and 3) - 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5) - 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt FPGA - 2 HW I2C busses - last but not least, the mandatory serial port The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb support and was changed according to our design (that means essentially removing what is not present on the designs and a few adaptations). There is currently only one prototype board that is based on this design and this patch also introduces it. The board is called kmlion1. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> kmp204x: update the ENV #define The comments had to be refined as well as the total size Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix ddr.c] Acked-by: York Sun <yorksun@freescale.com>
71 lines
1.7 KiB
C
71 lines
1.7 KiB
C
/*
|
|
* (C) Copyright 2013 Keymile AG
|
|
* Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <netdev.h>
|
|
#include <fm_eth.h>
|
|
#include <fsl_mdio.h>
|
|
#include <phy.h>
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int ret = 0;
|
|
#ifdef CONFIG_FMAN_ENET
|
|
struct fsl_pq_mdio_info dtsec_mdio_info;
|
|
|
|
printf("Initializing Fman\n");
|
|
|
|
dtsec_mdio_info.regs =
|
|
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
|
|
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
|
|
|
|
/* Register the real 1G MDIO bus */
|
|
fsl_pq_mdio_init(bis, &dtsec_mdio_info);
|
|
|
|
/* DTESC1/2 don't have a PHY, they are temporarily disabled
|
|
* so that u-boot doesn't try to unsuccessfuly enable them */
|
|
fm_disable_port(FM1_DTSEC1);
|
|
fm_disable_port(FM1_DTSEC2);
|
|
|
|
/*
|
|
* Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf
|
|
* This is the debug interface, the only one used in u-boot
|
|
*/
|
|
fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
|
|
fm_info_set_mdio(FM1_DTSEC5,
|
|
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
|
|
|
|
ret = cpu_eth_init(bis);
|
|
|
|
/* reenable DTSEC1/2 for later (kernel) */
|
|
fm_enable_port(FM1_DTSEC1);
|
|
fm_enable_port(FM1_DTSEC2);
|
|
#endif
|
|
|
|
return ret;
|
|
}
|
|
|
|
#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL)
|
|
|
|
#define mv88E1118_PAGE_REG 22
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) {
|
|
/* driver config is good */
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
/* but we still need to fix the LEDs */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|