u-boot/board/ge/mx53ppd/ppd_gpio.h
Peter Senna Tschudin 6b0071c110 mx53: Add Board support for GE PPD
Create board support for GE PPD, based on mx53loco.

Use mx53ppd_defconfig make target to configure for this board.

Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:59:02 +01:00

96 lines
3 KiB
C

/*
* (C) Copyright 2015 General Electric Company
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __PPD_GPIO_H_
#define __PPD_GPIO_H_
#include <asm/arch/iomux-mx53.h>
#include <asm/gpio.h>
#define PPD_UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP)
static const iomux_v3_cfg_t ppd_pads[] = {
/* FEC */
MX53_PAD_EIM_A22__GPIO2_16,
/* UART */
NEW_PAD_CTRL(MX53_PAD_PATA_DMACK__UART1_RXD_MUX, PPD_UART_PAD_CTRL),
NEW_PAD_CTRL(MX53_PAD_PATA_DIOW__UART1_TXD_MUX, PPD_UART_PAD_CTRL),
/* Video */
MX53_PAD_CSI0_DATA_EN__GPIO5_20, /* LR_SCAN_CTRL */
MX53_PAD_CSI0_VSYNC__GPIO5_21, /* UD_SCAN_CTRL */
MX53_PAD_CSI0_DAT10__GPIO5_28, /* DATA_WIDTH_CTRL */
MX53_PAD_CSI0_PIXCLK__GPIO5_18, /* HOST_CONTROLLED_RESET_TO_LCD_N */
MX53_PAD_EIM_DA2__GPIO3_2, /* LVDS1_MUX_CTRL */
MX53_PAD_EIM_DA3__GPIO3_3, /* LVDS0_MUX_CTRL */
MX53_PAD_EIM_A21__GPIO2_17, /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
MX53_PAD_CSI0_DAT11__GPIO5_29, /* BACKLIGHT_ENABLE */
MX53_PAD_DISP0_DAT9__PWM2_PWMO, /* IMX535_PWM2_TO_LCD_CONNECTOR */
/* I2C */
MX53_PAD_EIM_A20__GPIO2_18, /* RESET_I2C1_BUS_SEGMENT_MUX_N */
/* SPI */
MX53_PAD_DISP0_DAT23__GPIO5_17,
MX53_PAD_KEY_COL2__GPIO4_10,
MX53_PAD_KEY_ROW2__GPIO4_11,
MX53_PAD_KEY_COL3__GPIO4_12,
};
struct gpio_cfg {
unsigned int gpio;
int value;
};
#define RESET_IMX535_ETHERNET_PHY_N IMX_GPIO_NR(2, 16)
#define UD_SCAN_CTRL IMX_GPIO_NR(5, 21)
#define LR_SCAN_CTRL IMX_GPIO_NR(5, 20)
#define LVDS0_MUX_CTRL IMX_GPIO_NR(3, 3)
#define LVDS1_MUX_CTRL IMX_GPIO_NR(3, 2)
#define HOST_CONTROLLED_RESET_TO_LCD_N IMX_GPIO_NR(5, 18)
#define DATA_WIDTH_CTRL IMX_GPIO_NR(5, 28)
#define RESET_DP0_TRANSMITTER_N IMX_GPIO_NR(2, 28)
#define RESET_DP1_TRANSMITTER_N IMX_GPIO_NR(2, 29)
#define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22)
#define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27)
#define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17)
#define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29)
#define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18)
#define ECSPI1_CS0 IMX_GPIO_NR(5, 17)
#define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
#define ECSPI1_CS2 IMX_GPIO_NR(4, 11)
#define ECSPI1_CS3 IMX_GPIO_NR(4, 12)
static const struct gpio_cfg ppd_gpios[] = {
/* FEC */
/* Drive Low as GPIO output for 25ms per Eth Phy IX spec */
/* Then Drive High as GPIO output to bring Eth Phy IC out of reset */
{ RESET_IMX535_ETHERNET_PHY_N, 0 },
{ RESET_IMX535_ETHERNET_PHY_N, 1 },
/* Video */
{ UD_SCAN_CTRL, 0 },
{ LR_SCAN_CTRL, 1 },
#ifdef PROPRIETARY_CHANGES
{ LVDS0_MUX_CTRL, 1 },
#else
{ LVDS0_MUX_CTRL, 0 },
#endif
{ LVDS1_MUX_CTRL, 1 },
{ HOST_CONTROLLED_RESET_TO_LCD_N, 1 },
{ DATA_WIDTH_CTRL, 0 },
{ RESET_DP0_TRANSMITTER_N, 1 },
{ RESET_DP1_TRANSMITTER_N, 1 },
{ POWER_DOWN_LVDS0_DESERIALIZER_N, 1 },
{ POWER_DOWN_LVDS1_DESERIALIZER_N, 1 },
{ ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 },
{ BACKLIGHT_ENABLE, 0 },
{ RESET_I2C1_BUS_SEGMENT_MUX_N, 1 },
{ ECSPI1_CS0, 1 },
{ ECSPI1_CS1, 1 },
{ ECSPI1_CS2, 1 },
{ ECSPI1_CS3, 1 },
};
#endif /* __PPD_GPIO_H_ */