u-boot/include/configs/qemu-x86.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

50 lines
1.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <linux/sizes.h>
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(SCSI, scsi, 0) \
func(VIRTIO, virtio, 0) \
func(IDE, ide, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#include <configs/x86-common.h>
#define CONFIG_PREBOOT "pci enum"
#define CONFIG_SYS_MONITOR_LEN (1 << 20)
#define CONFIG_STD_DEVICES_SETTINGS "stdin=serial,i8042-kbd\0" \
"stdout=serial,vidconsole\0" \
"stderr=serial,vidconsole\0"
/*
* ATA/SATA support for QEMU x86 targets
* - Only legacy IDE controller is supported for QEMU '-M pc' target
* - AHCI controller is supported for QEMU '-M q35' target
*/
#define CONFIG_SYS_IDE_MAXBUS 2
#define CONFIG_SYS_IDE_MAXDEVICE 4
#define CONFIG_SYS_ATA_BASE_ADDR 0
#define CONFIG_SYS_ATA_DATA_OFFSET 0
#define CONFIG_SYS_ATA_REG_OFFSET 0
#define CONFIG_SYS_ATA_ALT_OFFSET 0
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x1f0
#define CONFIG_SYS_ATA_IDE1_OFFSET 0x170
#define CONFIG_ATAPI
#define CONFIG_SPL_BOARD_LOAD_IMAGE
#endif /* __CONFIG_H */