u-boot/arch/arm/dts/zynqmp-zc1751-xm016-dc2.dts
Piyush Mehta d036f4f2c6 arm64: dts: zynqmp: Enable USB2.0 for zc1751-xm016-dc2
The board zynqmp-zc1751-xm016-dc2 support only USB2.0.
This patch removes USB3.0 DT configuration for DC2 board.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:18:45 +02:00

550 lines
9.3 KiB
Text

// SPDX-License-Identifier: GPL-2.0+
/*
* dts file for Xilinx ZynqMP zc1751-xm016-dc2
*
* (C) Copyright 2015 - 2021, Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
/ {
model = "ZynqMP zc1751-xm016-dc2 RevA";
compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
aliases {
ethernet0 = &gem2;
i2c0 = &i2c0;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
spi0 = &spi0;
spi1 = &spi1;
usb0 = &usb1;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
};
};
&can0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can0_default>;
};
&can1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_default>;
};
&fpd_dma_chan1 {
status = "okay";
};
&fpd_dma_chan2 {
status = "okay";
};
&fpd_dma_chan3 {
status = "okay";
};
&fpd_dma_chan4 {
status = "okay";
};
&fpd_dma_chan5 {
status = "okay";
};
&fpd_dma_chan6 {
status = "okay";
};
&fpd_dma_chan7 {
status = "okay";
};
&fpd_dma_chan8 {
status = "okay";
};
&gem2 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem2_default>;
phy0: ethernet-phy@5 {
reg = <5>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
ti,dp83867-rxctrl-strap-quirk;
};
};
&gpio {
status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
pinctrl-1 = <&pinctrl_i2c0_gpio>;
scl-gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
tca6416_u26: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
/* IRQ not connected */
};
rtc@68 {
compatible = "dallas,ds1339";
reg = <0x68>;
};
};
&nand0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand0_default>;
arasan,has-mdma;
nand@0 {
reg = <0x0>;
#address-cells = <0x2>;
#size-cells = <0x1>;
nand-ecc-mode = "soft";
nand-ecc-algo = "bch";
nand-rb = <0>;
label = "main-storage-0";
partition@0 { /* for testing purpose */
label = "nand-fsbl-uboot";
reg = <0x0 0x0 0x400000>;
};
partition@1 { /* for testing purpose */
label = "nand-linux";
reg = <0x0 0x400000 0x1400000>;
};
partition@2 { /* for testing purpose */
label = "nand-device-tree";
reg = <0x0 0x1800000 0x400000>;
};
partition@3 { /* for testing purpose */
label = "nand-rootfs";
reg = <0x0 0x1c00000 0x1400000>;
};
partition@4 { /* for testing purpose */
label = "nand-bitstream";
reg = <0x0 0x3000000 0x400000>;
};
partition@5 { /* for testing purpose */
label = "nand-misc";
reg = <0x0 0x3400000 0xfcc00000>;
};
};
nand@1 {
reg = <0x1>;
#address-cells = <0x2>;
#size-cells = <0x1>;
nand-ecc-mode = "soft";
nand-ecc-algo = "bch";
nand-rb = <0>;
label = "main-storage-1";
partition@0 { /* for testing purpose */
label = "nand1-fsbl-uboot";
reg = <0x0 0x0 0x400000>;
};
partition@1 { /* for testing purpose */
label = "nand1-linux";
reg = <0x0 0x400000 0x1400000>;
};
partition@2 { /* for testing purpose */
label = "nand1-device-tree";
reg = <0x0 0x1800000 0x400000>;
};
partition@3 { /* for testing purpose */
label = "nand1-rootfs";
reg = <0x0 0x1c00000 0x1400000>;
};
partition@4 { /* for testing purpose */
label = "nand1-bitstream";
reg = <0x0 0x3000000 0x400000>;
};
partition@5 { /* for testing purpose */
label = "nand1-misc";
reg = <0x0 0x3400000 0xfcc00000>;
};
};
};
&pinctrl0 {
status = "okay";
pinctrl_can0_default: can0-default {
mux {
function = "can0";
groups = "can0_9_grp";
};
conf {
groups = "can0_9_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO38";
bias-high-impedance;
};
conf-tx {
pins = "MIO39";
bias-disable;
};
};
pinctrl_can1_default: can1-default {
mux {
function = "can1";
groups = "can1_8_grp";
};
conf {
groups = "can1_8_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO33";
bias-high-impedance;
};
conf-tx {
pins = "MIO32";
bias-disable;
};
};
pinctrl_i2c0_default: i2c0-default {
mux {
groups = "i2c0_1_grp";
function = "i2c0";
};
conf {
groups = "i2c0_1_grp";
bias-pull-up;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_i2c0_gpio: i2c0-gpio {
mux {
groups = "gpio0_6_grp", "gpio0_7_grp";
function = "gpio0";
};
conf {
groups = "gpio0_6_grp", "gpio0_7_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
};
pinctrl_uart0_default: uart0-default {
mux {
groups = "uart0_10_grp";
function = "uart0";
};
conf {
groups = "uart0_10_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO42";
bias-high-impedance;
};
conf-tx {
pins = "MIO43";
bias-disable;
};
};
pinctrl_uart1_default: uart1-default {
mux {
groups = "uart1_10_grp";
function = "uart1";
};
conf {
groups = "uart1_10_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO41";
bias-high-impedance;
};
conf-tx {
pins = "MIO40";
bias-disable;
};
};
pinctrl_usb1_default: usb1-default {
mux {
groups = "usb1_0_grp";
function = "usb1";
};
conf {
groups = "usb1_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO64", "MIO65", "MIO67";
bias-high-impedance;
};
conf-tx {
pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
"MIO72", "MIO73", "MIO74", "MIO75";
bias-disable;
};
};
pinctrl_gem2_default: gem2-default {
mux {
function = "ethernet2";
groups = "ethernet2_0_grp";
};
conf {
groups = "ethernet2_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
conf-rx {
pins = "MIO58", "MIO59", "MIO60", "MIO61", "MIO62",
"MIO63";
bias-high-impedance;
low-power-disable;
};
conf-tx {
pins = "MIO52", "MIO53", "MIO54", "MIO55", "MIO56",
"MIO57";
bias-disable;
low-power-enable;
};
mux-mdio {
function = "mdio2";
groups = "mdio2_0_grp";
};
conf-mdio {
groups = "mdio2_0_grp";
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
bias-disable;
};
};
pinctrl_nand0_default: nand0-default {
mux {
groups = "nand0_0_grp";
function = "nand0";
};
conf {
groups = "nand0_0_grp";
bias-pull-up;
};
mux-ce {
groups = "nand0_ce_0_grp";
function = "nand0_ce";
};
conf-ce {
groups = "nand0_ce_0_grp";
bias-pull-up;
};
mux-rb {
groups = "nand0_rb_0_grp";
function = "nand0_rb";
};
conf-rb {
groups = "nand0_rb_0_grp";
bias-pull-up;
};
mux-dqs {
groups = "nand0_dqs_0_grp";
function = "nand0_dqs";
};
conf-dqs {
groups = "nand0_dqs_0_grp";
bias-pull-up;
};
};
pinctrl_spi0_default: spi0-default {
mux {
groups = "spi0_0_grp";
function = "spi0";
};
conf {
groups = "spi0_0_grp";
bias-disable;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux-cs {
groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
"spi0_ss_2_grp";
function = "spi0_ss";
};
conf-cs {
groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
"spi0_ss_2_grp";
bias-disable;
};
};
pinctrl_spi1_default: spi1-default {
mux {
groups = "spi1_3_grp";
function = "spi1";
};
conf {
groups = "spi1_3_grp";
bias-disable;
slew-rate = <SLEW_RATE_SLOW>;
power-source = <IO_STANDARD_LVCMOS18>;
};
mux-cs {
groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
"spi1_ss_11_grp";
function = "spi1_ss";
};
conf-cs {
groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
"spi1_ss_11_grp";
bias-disable;
};
};
};
&rtc {
status = "okay";
};
&spi0 {
status = "okay";
num-cs = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0_default>;
spi0_flash0: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "sst,sst25wf080", "jedec,spi-nor";
spi-max-frequency = <50000000>;
reg = <0>;
partition@0 {
label = "spi0-data";
reg = <0x0 0x100000>;
};
};
};
&spi1 {
status = "okay";
num-cs = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1_default>;
spi1_flash0: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at45db041e", "atmel,at45", "atmel,dataflash";
spi-max-frequency = <20000000>;
reg = <0>;
partition@0 {
label = "spi1-data";
reg = <0x0 0x84000>;
};
};
};
/* ULPI SMSC USB3320 */
&usb1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb1_default>;
};
&dwc3_1 {
status = "okay";
dr_mode = "host";
};
&uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
};