mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 13:56:30 +00:00
01e62c7f11
This patch adds basic support for the Marvell Armada 3700 DB-88F3720 development board. Supported are the following interfaces: - UART - SPI (incl. SPI NOR) - I2C - Ethernet Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Wilson Ding <dingwei@marvell.com> Cc: Victor Gu <xigu@marvell.com> Cc: Hua Jing <jinghua@marvell.com> Cc: Terry Zhou <bjzhou@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Cc: Haim Boot <hayim@marvell.com>
134 lines
3 KiB
C
134 lines
3 KiB
C
/*
|
|
* Copyright (C) 2016 Stefan Roese <sr@denx.de>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* IO expander I2C device */
|
|
#define I2C_IO_EXP_ADDR 0x22
|
|
#define I2C_IO_CFG_REG_0 0x6
|
|
#define I2C_IO_DATA_OUT_REG_0 0x2
|
|
#define I2C_IO_REG_0_SATA_OFF 2
|
|
#define I2C_IO_REG_0_USB_H_OFF 1
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* Nothing to do (yet), perhaps later some pin-muxing etc */
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Board specific AHCI / SATA enable code */
|
|
int board_ahci_enable(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
u8 buf[8];
|
|
|
|
/* Configure IO exander PCA9555: 7bit address 0x22 */
|
|
ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
|
|
if (ret) {
|
|
printf("Cannot find PCA9555: %d\n", ret);
|
|
return 0;
|
|
}
|
|
|
|
ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to read IO expander value via I2C\n");
|
|
return -EIO;
|
|
}
|
|
|
|
/*
|
|
* Enable SATA power via IO expander connected via I2C by setting
|
|
* the corresponding bit to output mode to enable power for SATA
|
|
*/
|
|
buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF);
|
|
ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to set IO expander via I2C\n");
|
|
return -EIO;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Board specific xHCI enable code */
|
|
int board_xhci_enable(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
u8 buf[8];
|
|
|
|
/* Configure IO exander PCA9555: 7bit address 0x22 */
|
|
ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
|
|
if (ret) {
|
|
printf("Cannot find PCA9555: %d\n", ret);
|
|
return 0;
|
|
}
|
|
|
|
printf("Enable USB VBUS\n");
|
|
|
|
/*
|
|
* Read configuration (direction) and set VBUS pin as output
|
|
* (reset pin = output)
|
|
*/
|
|
ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to read IO expander value via I2C\n");
|
|
return -EIO;
|
|
}
|
|
buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
|
|
ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to set IO expander via I2C\n");
|
|
return -EIO;
|
|
}
|
|
|
|
/* Read VBUS output value and disable it */
|
|
ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to read IO expander value via I2C\n");
|
|
return -EIO;
|
|
}
|
|
buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
|
|
ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to set IO expander via I2C\n");
|
|
return -EIO;
|
|
}
|
|
|
|
/*
|
|
* Required delay for configuration to settle - must wait for
|
|
* power on port is disabled in case VBUS signal was high,
|
|
* required 3 seconds delay to let VBUS signal fully settle down
|
|
*/
|
|
mdelay(3000);
|
|
|
|
/* Enable VBUS power: Set output value of VBUS pin as enabled */
|
|
buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF);
|
|
ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
|
|
if (ret) {
|
|
printf("Failed to set IO expander via I2C\n");
|
|
return -EIO;
|
|
}
|
|
|
|
mdelay(500); /* required delay to let output value settle */
|
|
|
|
return 0;
|
|
}
|