mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-09-24 00:12:13 +00:00
7c2d5d1642
After the discussion here: https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/ which resulted in this patch: https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/ and many other discussions before it, notably: https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/ it became apparent that nobody really knows what "SGMII 2500" is. Certainly, Freescale/NXP hardware engineers name this protocol "SGMII 2500" in the reference manuals, but the PCS devices do not support any "SGMII" specific features when operating at the speed of 2500 Mbps, no in-band autoneg and no speed change via symbol replication . So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without in-band autoneg and at a fixed speed" is indistinguishable from "2500base-x without in-band autoneg", which is precisely what these NXP devices support. So it just appears that "SGMII 2500" is an unclear name with no clear definition that stuck. As such, in the Linux kernel, the drivers which use this SERDES protocol use the 2500base-x phy-mode. This patch converts U-Boot to use 2500base-x too, or at least, as much as it can. Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500 completely, but the mvpp2 driver seems to even distinguish between SGMII 2500 and 2500base-X. Namely, it enables in-band autoneg for one but not the other, and forces flow control for one but not the other. This goes back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500 is an MII protocol (connects a MAC to a PHY such as Aquantia), but the two are practically indistinguishable through everything except use case. NXP devices can support both use cases through an identical configuration, for example RX flow control can be unconditionally enabled in order to support rate adaptation performed by an Aquantia PHY. At least I can find no indication in online documents published by Cisco which would point towards "SGMII-2500" being an actual standard with an actual definition, so I cannot say "yes, NXP devices support it". Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> |
||
|---|---|---|
| .. | ||
| ddr.c | ||
| ddr.h | ||
| eth.c | ||
| Kconfig | ||
| ls1043aqds.c | ||
| ls1043aqds_pbi.cfg | ||
| ls1043aqds_qixis.h | ||
| ls1043aqds_rcw_nand.cfg | ||
| ls1043aqds_rcw_sd_ifc.cfg | ||
| ls1043aqds_rcw_sd_qspi.cfg | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Overview
--------
The LS1043A Development System (QDS) is a high-performance computing,
evaluation, and development platform that supports the QorIQ LS1043A
LayerScape Architecture processor. The LS1043AQDS provides SW development
platform for the Freescale LS1043A processor series, with a complete
debugging environment.
LS1043A SoC Overview
--------------------
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1043A
SoC overview.
LS1043AQDS board Overview
-----------------------
- SERDES Connections, 4 lanes supporting:
- PCI Express - 3.0
- SGMII, SGMII 2.5
- QSGMII
- SATA 3.0
- 10GBase-R
- DDR Controller
- 2GB 40bits (8-bits ECC) DDR4 SDRAM. Support rates of up to 1600MT/s
-IFC/Local Bus
- One in-socket 128 MB NOR flash 16-bit data bus
- One 512 MB NAND flash with ECC support
- PromJet Port
- FPGA connection
- USB 3.0
- Three high speed USB 3.0 ports
- First USB 3.0 port configured as Host with Type-A connector
- The other two USB 3.0 ports configured as OTG with micro-AB connector
- SDHC port connects directly to an adapter card slot, featuring:
- Optional clock feedback paths, and optional high-speed voltage translation assistance
- SD slots for SD, SDHC (1x, 4x, 8x), and/or MMC
- eMMC memory devices
- DSPI: Onboard support for three SPI flash memory devices
- 4 I2C controllers
- One SATA onboard connectors
- UART
- Two 4-pin serial ports at up to 115.2 Kbit/s
- Two DB9 D-Type connectors supporting one Serial port each
- ARM JTAG support
Memory map from core's view
----------------------------
Start Address End Address Description Size
0x00_0000_0000 0x00_000F_FFFF Secure Boot ROM 1MB
0x00_0100_0000 0x00_0FFF_FFFF CCSRBAR 240MB
0x00_1000_0000 0x00_1000_FFFF OCRAM0 64KB
0x00_1001_0000 0x00_1001_FFFF OCRAM1 64KB
0x00_2000_0000 0x00_20FF_FFFF DCSR 16MB
0x00_6000_0000 0x00_67FF_FFFF IFC - NOR Flash 128MB
0x00_7E80_0000 0x00_7E80_FFFF IFC - NAND Flash 64KB
0x00_7FB0_0000 0x00_7FB0_0FFF IFC - FPGA 4KB
0x00_8000_0000 0x00_FFFF_FFFF DRAM1 2GB
Booting Options
---------------
a) Promjet Boot
b) NOR boot
c) NAND boot
d) SD boot
e) QSPI boot