mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-08 14:14:32 +00:00
bcee8d6764
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass is included in SPL/TPL without any control for boards. Some boards may want to disable this to reduce code size where GPIOs are not needed in SPL or TPL. Add a new Kconfig option to permit this. Default it to 'y' so that existing boards work correctly. Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to preserve the current behaviour. Also update the 74x164 GPIO driver since it cannot build with SPL. This allows us to remove the hacks in config_uncmd_spl.h and Makefile.uncmd_spl (eventually those files should be removed). Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> |
||
|---|---|---|
| .. | ||
| apalis-imx8.c | ||
| apalis-imx8qm-imximage.cfg | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
U-Boot for the Toradex Apalis iMX8QM V1.0B Module
Quick Start
===========
- Build the ARM trusted firmware binary
- Get scfw_tcm.bin and ahab-container.img
- Build U-Boot
- Load U-Boot binary using uuu
- Flash U-Boot binary into the eMMC
- Boot
Get and Build the ARM Trusted Firmware
======================================
$ git clone -b imx_4.14.78_1.0.0_ga https://source.codeaurora.org/external/imx/imx-atf
$ cd imx-atf/
$ make PLAT=imx8qm bl31
Get scfw_tcm.bin and ahab-container.img
=======================================
$ wget https://github.com/toradex/meta-fsl-bsp-release/blob/toradex-sumo-4.14.78-1.0.0_ga-bringup/imx/meta-bsp/recipes-bsp/imx-sc-firmware/files/mx8qm-apalis-scfw-tcm.bin?raw=true
$ mv mx8qm-apalis-scfw-tcm.bin\?raw\=true mx8qm-apalis-scfw-tcm.bin
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
$ chmod +x firmware-imx-8.0.bin
$ ./firmware-imx-8.0.bin
Copy the following binaries to the U-Boot folder:
$ cp imx-atf/build/imx8qm/release/bl31.bin .
$ cp u-boot/u-boot.bin .
Copy the following firmware to the U-Boot folder:
$ cp firmware-imx-8.0/firmware/seco/ahab-container.img .
Build U-Boot
============
$ make apalis-imx8qm_defconfig
$ make u-boot-dtb.imx
Load the U-Boot Binary Using UUU
================================
Get the latest version of the universal update utility (uuu) aka mfgtools 3.0:
https://community.nxp.com/external-link.jspa?url=https%3A%2F%2Fgithub.com%2FNXPmicro%2Fmfgtools%2Freleases
Put the module into USB recovery aka serial downloader mode, connect USB device
to your host and execute uuu:
sudo ./uuu u-boot/u-boot-dtb.imx
Flash the U-Boot Binary into the eMMC
=====================================
Burn the u-boot-dtb.imx binary to the primary eMMC hardware boot area partition:
load mmc 1:1 $loadaddr u-boot-dtb.imx
setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200
mmc dev 0 1
mmc write ${loadaddr} 0x0 ${blkcnt}
Boot